scholarly journals Simplified 2D Finite Element Model for Calculation of the Bearing Capacity of Eccentrically Compressed Concrete-Filled Steel Tubular Columns

2021 ◽  
Vol 11 (24) ◽  
pp. 11645
Author(s):  
Anton Chepurnenko ◽  
Batyr Yazyev ◽  
Besarion Meskhi ◽  
Alexey Beskopylny ◽  
Kazbek Khashkhozhev ◽  
...  
Keyword(s):  
Finite Element ◽  
Bearing Capacity ◽  
Cross Sections ◽  
Three Dimensional ◽  
Element Model ◽  
Longitudinal Force ◽  
Effective Area ◽  
Element Analysis ◽  
Tubular Columns ◽  
Cfst Columns

Concrete-filled steel tubular (CFST) columns are widely used in construction due to effective resistance to compression and bending joint action. However, currently, there is no generally accepted effective calculation method considering both nonlinearities of the materials and lateral compression. The article proposes the finite element analysis method of concrete-filled steel tubular columns in a physically nonlinear formulation by reducing a three-dimensional problem to a two-dimensional one based on the hypothesis of plane sections. The equations of Geniev’s concrete theory of plasticity are used as relations establishing the relationship between stresses and strains. The technique was tested by comparing the solution with the calculation in a three-dimensional formulation in the LIRA-SAPR software package and with the experimental data of A.L. Krishan and A.I. Sagadatov. It has been established that the effective area of operation of circular-section columns are small eccentricities of the longitudinal force. The proposed approach can be applied to analyzing the stress–strain state and bearing capacity of pipe-concrete columns of arbitrary cross-sections. There are no restrictions on the composition of concrete, and the shell material can be steel and fiberglass.

scholarly journals Fire resistance of circulat steel tubes infilled with ultra-high strength concrete with external fire protection

2019 ◽  
Vol 39 (1) ◽  
pp. 71-80
Author(s):  
Xiao Lyu ◽  
Erfeng Du ◽  
Ran Li
Keyword(s):  
Finite Element ◽  
High Strength Concrete ◽  
Three Dimensional ◽  
High Strength ◽  
Element Model ◽  
Test Results ◽  
Element Analysis ◽  
Strength Concrete ◽  
Tubular Columns ◽  
Axially Loaded

In this paper, a non-linear three-dimensional finite element model is presented in order to study the behaviour of axially loaded ultra-high strength concrete filled circular hollow tubular columns exposed to fire. Ultra-high strength concrete with compressive strength greater than 180 N/mm2 has been developed for concrete filled tubes for use in high–rise buildings. This paper studies the structural performance of fire protected ultra-high strength concrete filled tubular columns exposed to the standard ISO fire. The aim of this work is to understand and represent the behaviour of axially loaded ultra-high strength concrete filled circular hollow tubular columns in fire situations and to compare calculation results with experiment. The numerical analyses are carried out using a general finite element analysis package ABAQUS and the results are validated against the test results in terms of heat distribution and mechanical behavior. Comparison with the test results showed a reasonable agreement with finite element results in terms of temperature prediction and load displacement behavior during the fire.

FEM Analysis of Concrete Filled Square Steel Tubular Columns with Energy Dissipation Plate

2012 ◽  
Vol 256-259 ◽  
pp. 666-669
Author(s):  
Cun Hui ◽  
Wan Lin Cao
Keyword(s):  
Finite Element ◽  
Energy Dissipation ◽  
Bearing Capacity ◽  
Fem Analysis ◽  
Seismic Energy ◽  
Element Model ◽  
Additional Energy ◽  
Tubular Columns ◽  
Structural Measure ◽  
Cfst Columns

In order to improve the seismic energy dissipation performance of concrete filled square steel tubular (CFST) columns, the structural measure about puting the additional energy dissipation plat at the bottom of the CFST columns where bears more stress, was proposed. Finite element anylsis of 10 CFST columns with different structural measure were performed under the same axial compression, selecting the thickness and height of the energy dissipation plate as parameters. On the basis of finite element anylasis, this paper, which obtained load-displacement curves of each finite element model, analyzed and compared the bearing capacity of each model. The results show that: comparing to the ordinary CFST columns, the columns with energy dissipation plat show better about bearing capacity and seismic performance, the height of the energy dissipation has a significant effect on bearing capacity but the thickness has less impact.

Torsional Analysis of a Steel Cord-Rubber Tire Belt Structure

1996 ◽  
Vol 24 (4) ◽  
pp. 339-348 ◽  
Author(s):  
R. M. V. Pidaparti
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Composite Structures ◽  
Three Dimensional ◽  
Element Model ◽  
Torsional Stiffness ◽  
Element Analysis ◽  
Rubber Belt ◽  
Steel Cord ◽  
Torsional Analysis

Abstract A three-dimensional (3D) beam finite element model was developed to investigate the torsional stiffness of a twisted steel-reinforced cord-rubber belt structure. The present 3D beam element takes into account the coupled extension, bending, and twisting deformations characteristic of the complex behavior of cord-rubber composite structures. The extension-twisting coupling due to the twisted nature of the cords was also considered in the finite element model. The results of torsional stiffness obtained from the finite element analysis for twisted cords and the two-ply steel cord-rubber belt structure are compared to the experimental data and other alternate solutions available in the literature. The effects of cord orientation, anisotropy, and rubber core surrounding the twisted cords on the torsional stiffness properties are presented and discussed.

Finite Element Analysis of Nonuniformity of Tires with Imperfections5

2007 ◽  
Vol 35 (3) ◽  
pp. 226-238 ◽  
Author(s):  
K. M. Jeong ◽  
K. W. Kim ◽  
H. G. Beom ◽  
J. U. Park
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Radial Force ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Dimensional Finite Element ◽  
Force Variation ◽  
Three Dimensional Finite Element

Abstract The effects of variations in stiffness and geometry on the nonuniformity of tires are investigated by using the finite element analysis. In order to evaluate tire uniformity, a three-dimensional finite element model of the tire with imperfections is developed. This paper considers how imperfections, such as variations in stiffness or geometry and run-out, contribute to detrimental effects on tire nonuniformity. It is found that the radial force variation of a tire with imperfections depends strongly on the geometrical variations of the tire.

scholarly journals Comparison of Tooth- and Bone-Borne Appliances on the Stress Distributions and Displacement Patterns in the Facial Skeleton in Surgically Assisted Rapid Maxillary Expansion—A Finite Element Analysis (FEA) Study

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1152
Author(s):  
Rafał Nowak ◽  
Anna Olejnik ◽  
Hanna Gerber ◽  
Roman Frątczak ◽  
Ewa Zawiślak
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Rapid Maxillary Expansion ◽  
Stress Distributions ◽  
Maxillary Expansion ◽  
Facial Skeleton ◽  
Element Analysis ◽  
Maxillary Constriction

The aim of this study was to compare the reduced stresses according to Huber’s hypothesis and the displacement pattern in the region of the facial skeleton using a tooth- or bone-borne appliance in surgically assisted rapid maxillary expansion (SARME). In the current literature, the lack of updated reports about biomechanical effects in bone-borne appliances used in SARME is noticeable. Finite element analysis (FEA) was used for this study. Six facial skeleton models were created, five with various variants of osteotomy and one without osteotomy. Two different appliances for maxillary expansion were used for each model. The three-dimensional (3D) model of the facial skeleton was created on the basis of spiral computed tomography (CT) scans of a 32-year-old patient with maxillary constriction. The finite element model was built using ANSYS 15.0 software, in which the computations were carried out. Stress distributions and displacement values along the 3D axes were found for each osteotomy variant with the expansion of the tooth- and the bone-borne devices at a level of 0.5 mm. The investigation showed that in the case of a full osteotomy of the maxilla, as described by Bell and Epker in 1976, the method of fixing the appliance for maxillary expansion had no impact on the distribution of the reduced stresses according to Huber’s hypothesis in the facial skeleton. In the case of the bone-borne appliance, the load on the teeth, which may lead to periodontal and orthodontic complications, was eliminated. In the case of a full osteotomy of the maxilla, displacements in the buccolingual direction for all the variables of the bone-borne appliance were slightly bigger than for the tooth-borne appliance.

Experimental Investigation of Stiffened Square CFST Columns under Axial Load

2014 ◽  
Vol 919-921 ◽  
pp. 1794-1800
Author(s):  
Xin Zhi Zheng ◽  
Xin Hua Zheng
Keyword(s):  
Experimental Investigation ◽  
Bearing Capacity ◽  
Cross Sections ◽  
Axial Load ◽  
Local Buckling ◽  
Test Results ◽  
Tubular Columns ◽  
Economical Benefit ◽  
Steel Consumption ◽  
Cfst Columns

Abstract: 7 square steel tubular columns were tested to discuss the ultimate axial bearing capacity, ductility performance and the steel consumption under stiffened by steel belts and binding bars of different cross-sections. Test results indicate that only by increasing fewer amounts of steel usage, stiffened square CFST columns with binding bars can not only improve the overall effects of restraint and alleviate regional local buckling between the binding bars, but also improve the bearing capacity of concrete filled square steel tubular columns. The utility benefits and the economical benefit is considerable, deserving extensive use.

The Optimum Cage Position and Orientation on the ALIF with Facet Screw Fixation: A Finite Element Analysis and the Taguchi Method

2011 ◽  
Vol 27 (3) ◽  
pp. 309-320 ◽  
Author(s):  
C.-Y. Fan ◽  
C.-K. Chao ◽  
C.-C. Hsu ◽  
K.-H. Chao
Keyword(s):  
Finite Element ◽  
Taguchi Method ◽  
Screw Fixation ◽  
Three Dimensional ◽  
Element Model ◽  
Lateral Position ◽  
Element Analysis ◽  
Control Factors ◽  
Position And Orientation ◽  
Noise Factors

ABSTRACTAnterior Lumbar Interbody Fusion (ALIF) has been widely used to treat internal disc degeneration. However, different cage positions and their orientations may affect the initial stability leading to different fusion results. The purpose of the present study is to investigate the optimum cage position and orientation for aiding an ALIF having a transfacet pedicle screw fixation (TFPS). A three-dimensional finite element model (ALIF with TFPS) has been developed to simulate the stability of the L4/L5 fusion segment under five different loading conditions. The Taguchi method was used to evaluate the optimized placement of the cages. Three control factors and two noise factors were included in the parameter design. The control factors included the anterior-posterior position, the medio-lateral position, and the convergent-divergent angle between the two cages. The compressive preload and the strengths of the cancellous bone were set as noise factors. From the results of the FEA and the Taguchi method, we suggest that the optimal cage positioning has a wide anterior placement, and a diverging angle between the two cages. The results show that the optimum cage position simultaneously contributes to a stronger support of the anterior column and lowers the risk of TFPS loosening.

Finite Element Analysis of the Effect of Surface Hardening Depth in Port Crane Wheel

2011 ◽  
Vol 291-294 ◽  
pp. 3282-3286 ◽  
Author(s):  
Jiang Wei Wu ◽  
Peng Wang
Keyword(s):  
Finite Element ◽  
Surface Hardening ◽  
Three Dimensional ◽  
Element Model ◽  
Contact Stresses ◽  
Numerical Results ◽  
Element Analysis ◽  
Finite Element Software ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element

In port crane industry, the surface hardening technique is widely used in order to improve the strength of wheel. But the hardening depth is chosen only by according to the experience, and the effect of different hardened depths is not studied theoretically. In this paper, the contact stresses in wheel with different hardening depth have been analyzed by applying three-dimensional finite element model. Based on this model, the ANSYS10.0 finite element software is used. The elastic wheel is used to verify the numerical results with the Hertz’s theory. Three different hardening depths, namely 10mm, 25mm and whole hardened wheel, under three different vertical loads were applied. The effect of hardening depth of a surface hardened wheel is discussed by comparing the contact stresses and contact areas from the numerical results.

Nonlinear Finite Element Analysis of Super-Long Pile and Soil Interaction in Soft Soil

2011 ◽  
Vol 201-203 ◽  
pp. 1601-1605 ◽  
Author(s):  
Shang Ping Chen ◽  
Wen Juan Yao ◽  
Sheng Qing Zhu
Keyword(s):  
Finite Element ◽  
Constitutive Model ◽  
Soft Soil ◽  
Three Dimensional ◽  
Nonlinear Behavior ◽  
Element Model ◽  
Element Analysis ◽  
Friction Resistance ◽  
Tip Resistance ◽  
Side Friction

In this paper, a nonlinear three-dimensional finite element model for super-long pile and soil interaction is established. In this model, contact elements are applied to simulate the nonlinear behavior of interaction of super-long pile and soil. A nonlinear elastic constitutive model for concrete is employed to analyze stress-strain relation of pile shaft under the axial load and the Duncan-Chang’s nonlinear constitutive model is used to reflect nonlinear and inelastic properties of soil. The side friction resistance, axial force, pile-tip resistance, and developing trend of soil plastic deformation are obtained and compared with measured results from static load tests. It is demonstrated that a super-long pile has the properties of degradation of side friction resistance and asynchronous action between side and pile-tip resistance, which is different from piles with a short to medium length.

Finite Element Analysis of Top-Hat–Stiffened Panels of Fiber-Reinforced–Plastic Boat Structures

2007 ◽  
Vol 44 (01) ◽  
pp. 16-26
Author(s):  
Ömer Eksik ◽  
R. Ajit Shenoi ◽  
Stuart S. J. Moy ◽  
Han Koo Jeong
Keyword(s):  
Finite Element ◽  
Lateral Pressure ◽  
Three Dimensional ◽  
Element Model ◽  
Stiffened Panel ◽  
Element Analysis ◽  
Stiffened Panels ◽  
Fiber Reinforced Plastic ◽  
Reinforced Plastic ◽  
Experimental Findings

This paper describes the development of a finite element model in order to assess the static response of a top-hat-stiffened panel under uniform lateral pressure. Systematic calculations were performed for deflection, strain, and stress using the developed model based on the ANSYS three-dimensional solid element (SOLID45). The numerical modeling results were compared to the experimental findings for validation and to further understand an internal stress pattern within the different constituents of the panel for explaining the likely causes of the panel failure. Good correlation between experimental and numerical strains and displacements was achieved.

Sign in / Sign up

Export Citation Format

Share Document