scholarly journals ELASTO-PLASTIC BUCKLING MODEL OF H-SECTION STEEL COLUMNS SUBJECTED TO CYCLIC BENDING MOMENT UNDER HIGH AXIAL FORCE

2016 ◽  
Vol 81 (728) ◽  
pp. 1723-1732 ◽  
Author(s):  
Toru TAKEUCHI ◽  
Ryota MATSUI ◽  
Hidetaka NAGAJI ◽  
Kunihiro MORISHITA
Keyword(s):  
Axial Force ◽  
Bending Moment ◽  
Plastic Buckling ◽  
Cyclic Bending ◽  
Steel Columns ◽  
Cyclic Bending Moment

Load Regime Diagram of a Pipe With Cyclically Plastic Bending

2002 ◽  
Author(s):  
Yanping Yao ◽  
Ming-Wan Lu
Keyword(s):  
Axial Force ◽  
Bending Moment ◽  
Boundary Curve ◽  
Plastic Behavior ◽  
Cyclic Bending ◽  
Elastic Plastic ◽  
Linear Elastic ◽  
Load Regime ◽  
Reversed Cyclic ◽  
Cyclic Bending Moment

The criteria of piping seismic design based on linear elastic analysis has been proved to be conservative, which is mainly because the influence of plastic deformation on piping dynamic response is neglected. In the present paper, a pipe under seismic excitation is simplified as an beam with tubular cross section subjected to steady axial force and fully reversed cyclic bending moment, and the elastic-plastic behavior of the pipe is studied. Various behavior of the pipe under different combinations of axial force and cyclic bending moment is discussed and the boundary curve equations between them are obtained. Also the load regime diagram for a pipe which is formed by the boundary curve equations in the loading plane is given, from which the elastic-plastic behavior of the pipe can be determined directly.

EXPERIMENTAL STUDY ON DEEP‐COLUMN SUBJECT TO COMPRESSIVE AXIAL FORCE WITH ONE END CYCLIC BENDING MOMENT

ce/papers ◽  
2019 ◽  
Vol 3 (5-6) ◽  
pp. 203-212
Author(s):  
Shimpei Yoshioka ◽  
Atsushi Sato ◽  
Takeshi Onogi
Keyword(s):  
Experimental Study ◽  
Axial Force ◽  
Bending Moment ◽  
Cyclic Bending ◽  
Compressive Axial Force ◽  
Cyclic Bending Moment

Finite Element Modeling of Self-Loosening of Bolted Joints

2004 ◽  
Author(s):  
Ming Zhang ◽  
Yanyao Jiang ◽  
Chu-Hwa Lee
Keyword(s):  
Finite Element ◽  
Contact Pressure ◽  
Bending Moment ◽  
Shear Loading ◽  
Transverse Load ◽  
Fe Model ◽  
Bolted Joint ◽  
Cyclic Bending ◽  
Second Stage ◽  
Cyclic Bending Moment

A three-dimensional finite element (FE) model with the consideration of the helix angle of the threads was developed to simulate the second stage self-loosening of a bolted joint. The second stage self-loosening refers to the graduate reduction in clamping force due to the back-off of the nut. The simulations were conducted for two plates jointed by a bolt and a nut and the joint was subjected to transverse or shear loading. An M12×1.75 bolt was used. The application of the preload was simulated by using an orthogonal temperature expansion method. FE simulations were conducted for several loading conditions with different preloads and relative displacements between the two clamped plates. It was found that due to the application of the cyclic transverse load, micro-slip occurred between the contacting surfaces of the engaged threads of the bolt and the nut. In addition, a cyclic bending moment was introduced on the bolted joint. The cyclic bending moment resulted in an oscillation of the contact pressure on the contacting surfaces of the engaged threads. The micro-slip between the engaged threads and the variation of the contact pressure were identified to be the major mechanisms responsible for the self-loosening of a bolted joint. Simplified finite element models were developed that confirmed the mechanisms discovered. The major self-loosening behavior of a bolted joint can be properly reproduced with the FE model developed. The results obtained agree quantitatively with the experimental observations.

Ratcheting assessment of corroded elbow pipes subjected to internal pressure and cyclic bending moment

2021 ◽  
pp. 030932472198989
Author(s):  
Ali Salehi ◽  
Armin Rahmatfam ◽  
Mohammad Zehsaz
Keyword(s):  
Growth Rate ◽  
Stainless Steel ◽  
Internal Pressure ◽  
Bending Moment ◽  
Axial Direction ◽  
Hoop Strain ◽  
Cyclic Bending ◽  
High Fatigue ◽  
The Impact ◽  
Cyclic Bending Moment

The present study aimed to study ratcheting strains of corroded stainless steel 304LN elbow pipes subjected to internal pressure and cyclic bending moment. To this aim, spherical and cubical shapes corrosion are applied at two depths of 1 mm and 2 mm in the critical points of elbow pipe such as symmetry sites at intrados, extrados, and crown positions. Then, a Duplex 2205 stainless steel elbow pipe is considered as an alternative to studying the impact of the pipe materials, due to its high corrosion resistance and strength, toughness, and most importantly, the high fatigue strength and other mechanical properties than stainless steel 304LN. In order to perform numerical analyzes, the hardening coefficients of the materials were calculated. The results highlight a significant relationship between the destructive effects of corrosion and the depth and shape of corrosion, so that as corrosion increases, the resulting destructive effects increases as well, also, the ratcheting strains in cubic corrosions have a higher growth rate than spherical corrosions. In addition, the growth rate of the ratcheting strains in the hoop direction is much higher across the studied sample than the axial direction. The highest growth rate of hoop strain was observed at crown and the highest growth rate of axial strains occurred at intrados position. Altogether, Duplex 2205 material has a better performance than SS 304LN.

Finite Element Modeling of Self-Loosening of Bolted Joints

2006 ◽  
Vol 129 (2) ◽  
pp. 218-226 ◽  
Author(s):  
Ming Zhang ◽  
Yanyao Jiang ◽  
Chu-Hwa Lee
Keyword(s):  
Finite Element ◽  
Contact Pressure ◽  
Bending Moment ◽  
Shear Loading ◽  
Transverse Load ◽  
Fe Model ◽  
Bolted Joint ◽  
Cyclic Bending ◽  
Second Stage ◽  
Cyclic Bending Moment

A three-dimensional finite element (FE) model with the consideration of the helix angle of the threads was developed to simulate the second stage self-loosening of a bolted joint. The second stage self-loosening refers to the gradual reduction in clamping force due to the back-off of the nut. The simulations were conducted for two plates jointed by a bolt and a nut and the joint was subjected to transverse or shear loading. An M12×1.75 bolt was used. The application of the preload was simulated by using an orthogonal temperature expansion method. FE simulations were conducted for several loading conditions with different preloads and relative displacements between the two clamped plates. It was found that due to the application of the cyclic transverse load, microslip occurred between the contacting surfaces of the engaged threads of the bolt and the nut. In addition, a cyclic bending moment was introduced on the bolted joint. The cyclic bending moment resulted in an oscillation of the contact pressure on the contacting surfaces of the engaged threads. The microslip between the engaged threads and the variation of the contact pressure were identified to be the major mechanisms responsible for the self-loosening of a bolted joint. Simplified finite element models were developed that confirmed the mechanisms discovered. The major self-loosening behavior of a bolted joint can be properly reproduced with the FE model developed. The results obtained agree quantitatively with the experimental observations.

Sign in / Sign up

Export Citation Format

Share Document