Effect of mechanical stress on electrochemical corrosion of X65 carbon steel in CO2 saturated brine

2020 ◽  
Vol 62 (8) ◽  
pp. 803-808
Author(s):  
Wei Yan
Keyword(s):  
Carbon Steel ◽  
Mechanical Stress ◽  
Electrochemical Corrosion

scholarly journals Electrochemical Corrosion of Ultra-high Strength Carbon Steel in Alkaline Brines Containing Hydrogen Sulfide

2016 ◽  
Vol 212 ◽  
pp. 998-1009 ◽  
Author(s):  
Ruishu Feng ◽  
Justin Beck ◽  
Margaret Ziomek-Moroz ◽  
Serguei N. Lvov
Keyword(s):  
Hydrogen Sulfide ◽  
Carbon Steel ◽  
Electrochemical Corrosion ◽  
High Strength

Effect of Nanoparticle Addition in Hybrid Sol-Gel Silane Coating on Corrosion Resistance of Low Carbon Steel

2013 ◽  
Vol 686 ◽  
pp. 244-249 ◽  
Author(s):  
Poovarasi Balan ◽  
Aaron Ng ◽  
Chee Beng Siang ◽  
R.K. Singh Raman ◽  
Eng Seng Chan
Keyword(s):  
Corrosion Resistance ◽  
Carbon Steel ◽  
Electrochemical Impedance ◽  
Sol Gel ◽  
Low Carbon Steel ◽  
Electrochemical Corrosion ◽  
Alumina Nanoparticles ◽  
Low Carbon ◽  
Silane Coating ◽  
Sol Gel Films

Chromium pre-treatments of metal have been replaced by silane pre-treatments as more environmental friendly option. Nanoparticles can be added in the silane sol-gel network have been reported to improve corrosion resistance. In this work, the electrochemical corrosion resistance of low carbon steel coated with hybrid organic-inorganic sol-gel film filled with nanoparticles was evaluated. The sol-gel films have been synthesized from 3-glycidoxy-propyl-trimethoxy-silane (3-GPTMS) and tetra-ethyl-ortho-silicate (TEOS) precursors. These films have been impregnated with 300 ppm of silica or alumina nanoparticles. The electrochemical behavior of the coated steel was evaluated by means of electrochemical impedance spectroscopy (EIS) and scanning electron microscopy (SEM). Equivalent circuit modeling, used for quantifying the EIS measurements showed that sol-gel films containing silica nanoparticles improved the barrier properties of the silane coating. The silica nanoparticle-containing films showed highest initial pore resistance over the five days of immersion in 0.05M NaCl.

Localized Electrochemical Corrosion Characteristics of Carbon Steel in Seawater

2013 ◽  
Vol 842 ◽  
pp. 104-109
Author(s):  
Yan Zou ◽  
Qiang Bai ◽  
Jia Wang ◽  
Wei Wang ◽  
Xiang Feng Kong
Keyword(s):  
Carbon Steel ◽  
Water Surface ◽  
Immersion Time ◽  
Electrochemical Corrosion ◽  
Corrosion Products ◽  
Local Corrosion ◽  
Immersion Period ◽  
Wire Beam Electrode

The galvanic and potential distributions of carbon steel immersed in seawater were studied by wire beam electrode (WBE) technique. Results indicated that the corrosion of carbon steel in seawater tended to local corrosion. With immersion time increasing, local corrosion was more and more serious. During the initial immersion period, the top of the coupon near the water surface was main cathode. With the corrosion extended, corrosion products gradually gathered on the surface of the carbon steel. Potential differences between cathode and anode gradually became small. Cathode and anode redistributed on the surface of carbon steel. At last, the top and the bottom were cathode while the middle was anode. The areas of anode first increased and then decreased. The areas of cathode were in contrast.

Apparent Inversion of the Effect of Alloyed Molybdenum for Corrosion of Ordinary and Enhanced 316L Stainless Steel in Sulfuric Acid

2008 ◽  
Vol 1107 ◽  
Author(s):  
Gloria Kwong ◽  
Anatolie Carcea ◽  
Roger C. Newman
Keyword(s):  
Stainless Steel ◽  
Carbon Steel ◽  
Corrosion Test ◽  
316L Stainless Steel ◽  
Storage System ◽  
Electrochemical Corrosion ◽  
Premature Failure ◽  
316L Steel ◽  
Electrochemical Corrosion Test ◽  
Spent Resin

AbstractAn aging assessment of the OPG waste resin storage system predicted the potential for premature failure of the carbon steel resin liners. Consequently, resin liners made of 316L stainless steel with a minimum content of 2.5% molybdenum were selected to replace the carbon steel liners. The 2.5% Mo 316L stainless steel was specified to enhance pitting resistance in the spent resin environment. With the additional Mo, one would expect that a brief electrochemical corrosion test will reveal the superiority of such alloy over conventional 316L steel. This study reports a contrary experience

Sign in / Sign up

Export Citation Format

Share Document