Preliminary Field Validation of Simple Performance Tests for Permanent Deformation: Case Study

2003 ◽  
Vol 1832 (1) ◽  
pp. 209-216 ◽  
Author(s):  
Fujie Zhou ◽  
Tom Scullion
Keyword(s):  
Dynamic Modulus ◽  
Permanent Deformation ◽  
Mixture Design ◽  
Asphalt Mixtures ◽  
Load Test ◽  
Performance Tests ◽  
Field Validation ◽  
Dynamic Modulus Test ◽  
Repeated Load

Simple performance tests (SPTs) to be used with the Superpave® volumetric mixture design procedure were recently recommended by NCHRP Project 9-19 (Simple Performance Test for Superpave Mix Design). Field validation of the SPTs is critical to their final acceptance and implementation in Superpave mixture design practice. Special Pavement Studies-1 (SPS-1) prematurely rutted sections on US-281 in Texas were used to validate the SPTs for permanent deformation, including the dynamic modulus test and repeated-load test and associated rutting indicators E*/sin δ and flow number ( F n), respectively. The results of this case study clearly show that both the dynamic modulus test and E*/sin δ and the repeated-load test and F n can effectively distinguish the good mixtures from the bad. Compared with E*/sin δ, F n can better differentiate the performance of asphalt mixtures. These results preliminarily validated both SPTs for permanent deformation. In addition, the location of the tertiary point in the plot of permanent strain versus number of load repetitions is clarified; a simple linear model needs to be added in order to determine the F n. Furthermore, the possibility of using the number of load repetitions ( Nps) corresponding to the initial point of the secondary stage to characterize the rutting resistance of asphalt mixtures is discussed. The new indicator proposed is supported by the limited data presented in this paper and can be easily determined and can reduce test duration significantly.

Permanent deformation response parameters of asphalt mixtures for a new mix-confined repeated load test

2013 ◽  
Vol 20 (5) ◽  
pp. 1434-1442 ◽  
Author(s):  
Gong-yun Liao ◽  
Yi-wen Yang ◽  
Xiao-ming Huang ◽  
Jin-yuan Xiang
Keyword(s):  
Permanent Deformation ◽  
Asphalt Mixtures ◽  
Load Test ◽  
Deformation Response ◽  
Repeated Load

Performance of Virginia’s Early Foamed Warm Mix Asphalt Mixtures

2018 ◽  
Vol 2672 (28) ◽  
pp. 178-189 ◽  
Author(s):  
Stacey D. Diefenderfer
Keyword(s):  
Dynamic Modulus ◽  
Permanent Deformation ◽  
Warm Mix Asphalt ◽  
Department Of Transportation ◽  
High Dynamic ◽  
Repeated Load ◽  
And Performance ◽  
Virginia Department ◽  
Performance Grading ◽  
Air Void

The Virginia Department of Transportation began allowing the use of warm mix asphalt (WMA) in 2008. Although several WMA technologies were investigated prior to implementation, foamed WMA was not. This study evaluated the properties and performance of foamed WMA placed during the initial implementation of the technology to determine whether the technology had performed as expected. Six mixtures produced using plant foaming technologies and placed between 2008 and 2010 were identified and subjected to field coring and laboratory testing. Coring was performed in 2014, resulting in pavement ages from 4 to 6 years. Three comparable hot mix asphalt (HMA) mixtures were cored at 5 years for comparison. Cores were evaluated for air-void contents and permeability and were subjected to dynamic modulus, repeated load permanent deformation, and overlay testing. In addition, binder was extracted and recovered for performance grading. Similar properties were found for the WMA and HMA mixtures. One WMA mixture had high dynamic modulus and binder stiffness, but overlay testing did not indicate any tendency for premature cracking. All binders had aged between two and three performance grades above that specified at construction. WMA binders and one HMA binder aged two grades higher, and the remaining two HMA binders aged three grades higher, indicating a likely influence on aging of the reduced temperatures at which the early foamed mixtures were typically produced. Overall results indicated that foamed WMA and HMA mixtures should be expected to perform similarly.

Expedited Testing Program for Performance Characterization of Asphalt Mixtures

2019 ◽  
Vol 2673 (12) ◽  
pp. 225-233
Author(s):  
Intikhab Haidar ◽  
Charles W. Schwartz ◽  
Sadaf Khosravifar
Keyword(s):  
Permanent Deformation ◽  
Performance Testing ◽  
Testing Procedure ◽  
Test Methods ◽  
Asphalt Mixtures ◽  
Test Specifications ◽  
Research Grade ◽  
Repeated Load ◽  
Lengthy Process

The past two decades have seen significant efforts to standardize a series of simplified test methods to characterize the dynamic modulus (DM) and repeated load permanent deformation (RLPD) performance characteristics of asphalt mixtures using the asphalt mixtures performance tester (AMPT). While the current AASHTO T 79 test specifications for the AMPT are faster and easier to perform than their preceding research grade test protocols, there is still reluctance among highway agencies and industry to conduct performance testing using the AMPT. One significant reason is the lengthy process of sample preparation and testing for the DM and RLPD tests. Two studies to expedite this process are reported here. First, the potential for abbreviating the DM testing procedure was examined. It provides the option to fully exclude testing at 40°C by adding an additional frequency of 0.01 Hz at 20°C. This approach reduces time for testing as well as for sample conditioning at high temperature. Second, the possibility of reducing the total number of required specimens was evaluated. The variation of the DM under repetitive testing and the appropriateness of performing the RLPD test on samples already tested for DM were evaluated. The results showed that specimen damage or densification because of DM testing is insignificant. As a consequence, DM test specimens can be re-used for RLPD testing, reducing the required number of samples from 12 to 9.

Rheological Properties of High Grade Asphalt and its Mixture

2014 ◽  
Vol 599 ◽  
pp. 244-247 ◽  
Author(s):  
Qun Shan Ye ◽  
Chang Jian Ye ◽  
Zhi Lin Sun
Keyword(s):  
Rheological Properties ◽  
Dynamic Modulus ◽  
Permanent Deformation ◽  
Asphalt Binder ◽  
Asphalt Mixture ◽  
Asphalt Binders ◽  
Test Results ◽  
Complex Shear Modulus ◽  
Complex Shear ◽  
Dynamic Modulus Test

Viscosity test, dynamic shear test, dynamic modulus test and creep test were conducted to investigate the rheological properties of high modulus asphalt and its mixture. Test results indicated that the viscosity of hard grade asphalt could be increased when compared with the ordinary asphalt, especially at high temperatures. The complex shear modulus and dynamic modulus of hard-grade asphalt binder and its mixture were increased, which implied that the stiffness of them was enhanced. Furthermore, the elastically portions for viscoelastic property of asphalt binders were increased, which resulted in the reduction of phase angle for hard grade asphalt binders and mixtures. The rutting parameter for hard-grade asphalt mixture was increased remarkably, which revealed that the resistance to permanent deformation could be significantly improved for hard grade asphalt mixture.

Numerical and Graphical Method to Assess Permanent Deformation Potential for Repeated Compressive Loading of Asphalt Mixtures

2000 ◽  
Vol 1723 (1) ◽  
pp. 150-158 ◽  
Author(s):  
Rajesh K. Bhairampally ◽  
Robert L. Lytton ◽  
Dallas N. Little
Keyword(s):  
Strain Energy ◽  
Graphical Method ◽  
Permanent Deformation ◽  
Compressive Loading ◽  
Hydrated Lime ◽  
Numerical Approach ◽  
Empirical Models ◽  
Asphalt Mixtures ◽  
Deformation Potential ◽  
Repeated Load

Repeated-load permanent deformation testing has long been a popular way to characterize the performance of asphalt mixtures and to account for damage that leads to rutting. A number of empirical models have been used to fit repeated-load permanent deformation data. One such model, developed by Tseng and Lytton in 1989, fits permanent deformation data of most asphalt mixtures well. However, some mixtures exhibit a rate of damage that is in excess of that predicted by the 1989 Tseng and Lytton model. A numerical adaptation of the Tseng and Lytton empirical model is presented that readily characterizes such damage-susceptible mixtures. The excessive rate of damage is explained and reconciled in terms of plastic work theory and dissipated strain energy. The numerical approach is used to demonstrate the corrective effects of two types of additives to the mixtures: a recycled coproduct and hydrated lime.

Characteristic Analysis of Dynamic Modulus for High Modulus Asphalt Concrete

2014 ◽  
Vol 505-506 ◽  
pp. 15-18 ◽  
Author(s):  
Xiao Long Zou ◽  
Ai Min Sha ◽  
Wei Jiang ◽  
Xin Yan Huang
Keyword(s):  
Dynamic Modulus ◽  
Testing Machine ◽  
Asphalt Mixture ◽  
Asphalt Mixtures ◽  
High Modulus ◽  
Characteristic Analysis ◽  
Modified Asphalt ◽  
Universal Testing ◽  
Different Temperatures ◽  
Dynamic Modulus Test

In order to analyze the characteristics of high modulus asphalt mixture dynamic modulus, Universal Testing Machine (UTM-25) was used for dynamic modulus test of three kinds of mixtures, which were PR Module modified asphalt mixture and PR PLAST.S modified asphalt mixture and virgin asphalt mixture, to investigate dynamic modulus and phase angle at different temperatures and frequencies. The results indicate that: the dynamic modulus order of the three asphalt mixtures is PR MODULE > PR PLAST.S > Virgin. PR MODULE asphalt mixture dynamic modulus is much larger than the other two.

scholarly journals Comparative Study on Complex Modulus and Dynamic Modulus of High-Modulus Asphalt Mixture

Coatings ◽  
2021 ◽  
Vol 11 (12) ◽  
pp. 1502
Author(s):  
Licheng Guo ◽  
Qinsheng Xu ◽  
Guodong Zeng ◽  
Wenjuan Wu ◽  
Min Zhou ◽  
...  
Keyword(s):  
Dynamic Modulus ◽  
Complex Modulus ◽  
Asphalt Mixture ◽  
Asphalt Mixtures ◽  
Design System ◽  
High Modulus ◽  
Stiffness Modulus ◽  
Two Systems ◽  
Value Range ◽  
Dynamic Modulus Test

In the French high-modulus asphalt mixture design system, the complex modulus of the mixture under the conditions of 15 °C and 10 Hz is taken as the design index. However, in China, the dynamic modulus under the conditions of 15 °C, 10 Hz, 20 °C, 10 Hz and 45 °C, 10 Hz was taken as the stiffness modulus index of high-modulus asphalt mixture. The difference in modulus values between the two systems caused the pavement structure layer to be thicker and the construction cost to be higher in China. In order to find out the appropriate modulus value of high-modulus asphalt mixture suitable for China’s modulus parameter conditions to better carry out the reasonable design and evaluation of high-modulus asphalt mixture in China, the modulus of four types of high-modulus asphalt mixtures under the two systems through the two-point bending complex modulus test of the CRT-2PT trapezoidal beam and the SPT uniaxial compression dynamic modulus test were analyzed in this paper. Under the premise of meeting the stiffness modulus index of the French high-modulus asphalt mixture, the relationship conversion models between the dynamic modulus and complex modulus of high-modulus asphalt mixture under different temperatures were established. According to the conversion models, the design evaluation value range of dynamic modulus suitable for China’s condition was recommended. It is recommended that the dynamic modulus of China’s high-modulus asphalt mixture at 15 °C and 10 Hz is not less than 16,000 MPa, the dynamic modulus at 20 °C and 10 Hz is not less than 14,000 MPa, and the dynamic modulus at 45 °C and 10 Hz is not less than 2500 MPa. Five kinds of high-modulus asphalt mixtures used in actual road engineering were tested to verify the reliability of the recommended dynamic modulus values based on the modulus conversion model, and the results are consistent with the recommended value range of the model.

scholarly journals Effectiveness of Micro- and Nanomaterials in Asphalt Mixtures through Dynamic Modulus and Rutting Tests

2016 ◽  
Vol 2016 ◽  
pp. 1-14 ◽  
Author(s):  
Hui Yao ◽  
Zhanping You
Keyword(s):  
Dynamic Modulus ◽  
Mechanical Performance ◽  
Permanent Deformation ◽  
Asphalt Mixture ◽  
Asphalt Mixtures ◽  
Asphalt Binders ◽  
Test Results ◽  
Modified Asphalt ◽  
Overall Performance ◽  
Carbon Microfiber

The objectives of this research are to use micro- and nanomaterials to modify the asphalt mixture and to evaluate the mechanical performance of asphalt mixtures. These micro- and nanomaterials, including carbon microfiber, Nanomer material, nanosilica, nonmodified nanoclay, and polymer modified nanoclay, were selected to blend with the control asphalt to improve the overall performance of the modified asphalt binders and mixtures. The microstructures of original materials and asphalt binders were observed by the field emission scanning electron microscope (FE-SEM). The mixture performance tests were employed to evaluate the resistance to rutting and permanent deformation of the modified asphalt mixtures. Test results indicate that(1)the dynamic modulus of micro- and nanomodified asphalt mixtures improved significantly;(2)the rutting susceptibility of the modified asphalt mixtures was reduced significantly compared to that of the control asphalt mixture;(3)the microstructures of modified asphalt binders were different from the control asphalt, and the structures determine the improvement in the performance of modified asphalt mixtures. These results indicate that the addition of micro- and nanomaterials enhanced the rutting performance and strength of asphalt mixtures. In addition, the analysis of variance (ANOVA) was used to analyze the modifying effects of micro- and nanomaterials on the performance.

Sign in / Sign up

Export Citation Format

Share Document