Live-Load Test Results of Missouri’s First High-Performance Concrete Superstructure Bridge

2003 ◽  
Vol 1845 (1) ◽  
pp. 96-103 ◽  
Author(s):  
Yumin Yang ◽  
John J. Myers
Keyword(s):  
Load Distribution ◽  
High Performance ◽  
High Performance Concrete ◽  
Large Diameter ◽  
Load Test ◽  
Strain Gauges ◽  
Live Load ◽  
Test Results ◽  
Live Load Distribution ◽  
Live Load Test

For its significant economical savings and greater design flexibility, high-performance concrete (HPC) is becoming more widely used in highway bridge structures. High-performance bridges with HPC and large-diameter prestressed strands are becoming attractive to designers. Bridge A6130 is the first fully HPC superstructure bridge in Missouri. The bridge has HPC cast-in-place deck and high-strength concrete girders reinforced with 15.2-mm (0.6-in.) diameter strands. The bridge was instrumented with embedded strain gauges and thermocouples to monitor the early-age and later-age behavior of the structures from construction through service. To investigate the overall behavior of the bridge under live load, a static live-load test was developed and carried out. During the live-load test, 64 embedded vibrating wire strain gauges and 14 embedded electrical-resistance strain gauges were used to acquire the changing strain rate in the bridge caused by the varying live-load conditions. Girder deflections and rotations were also recorded with external sensors and a data acquisition system. Based on the test results, the load distribution to the girders was studied. The AASHTO specifications live-load distribution factor recommended for design was compared with the measured value and found to be overly conservative. The AASHTO load and resistance factor design live-load distribution factors recommended for design were found to be comparable to measured values. Two finite element models were developed with ANSYS and compared with measured values to investigate the continuity level of the Missouri Department of Transportation interior bent detail.

scholarly journals Live Load Distribution Factors for Skew Stringer Bridges with High-Performance-Steel Girders under Truck Loads

2018 ◽  
Vol 8 (10) ◽  
pp. 1717 ◽  
Author(s):  
Iman Mohseni ◽  
Yong Cho ◽  
Junsuk Kang
Keyword(s):  
Load Distribution ◽  
Shear Force ◽  
High Performance ◽  
Structural Parameters ◽  
Highway Bridges ◽  
Live Load ◽  
High Performance Steel ◽  
Live Load Distribution Factors ◽  
Live Load Distribution ◽  
Load Distribution Factors

Because the methods used to compute the live load distribution for moment and shear force in modern highway bridges subjected to vehicle loading are generally constrained by their range of applicability, refined analysis methods are necessary when this range is exceeded or new materials are used. This study developed a simplified method to calculate the live load distribution factors for skewed composite slab-on-girder bridges with high-performance-steel (HPS) girders whose parameters exceed the range of applicability defined by the American Association of State Highway and Transportation Officials (AASHTO)’s Load and Resistance Factor Design (LRFD) specifications. Bridge databases containing information on actual bridges and prototype bridges constructed from three different types of steel and structural parameters that exceeded the range of applicability were developed and the bridge modeling verified using results reported for field tests of actual bridges. The resulting simplified equations for the live load distribution factors of shear force and bending moment were based on a rigorous statistical analysis of the data. The proposed equations provided comparable results to those obtained using finite element analysis, giving bridge engineers greater flexibility when designing bridges with structural parameters that are outside the range of applicability defined by AASHTO in terms of span length, skewness, and bridge width.

Loading Tests of Thin Plates Made of Ultra-High Performance Concrete Reinforced by PVA Fibers and 2D Textile Glass Reinforcement

2015 ◽  
Vol 1095 ◽  
pp. 569-572 ◽  
Author(s):  
Petr Tej ◽  
Jiří Kolísko ◽  
Petr Bouška ◽  
Tomáš Bittner ◽  
Veronika Mušutová
Keyword(s):  
High Performance ◽  
High Performance Concrete ◽  
Load Test ◽  
Thin Plates ◽  
Test Results ◽  
Ultra High Performance Concrete ◽  
Four Point Bending ◽  
Computer Analyses ◽  
Loading Tests ◽  
Glass Reinforcement

This paper focuses on the research carried out on thin plates made of white ultra-high performance concrete reinforced by PVA fibers and 2D textile glass reinforcement. These boards should be used for facades or roof panels. The paper presents a computer and experimental analysis of the loading of thin UHPC plates. For the purpose of the experiments, three specimens of a size of 750 x 125 x 15 mm were made. The specimens were subsequently tested in the laboratory in four-point bending tests. The paper presents the process and results of the experiments. Simultaneously with the experiments, computer analyses were created in which optimization of the material and geometric parameters of the beams were carried out. The paper demonstrates the correspondence of the experimental and computer-simulated load test results.

Development of Some Performance-Based Material Specifications for High-Performance Concrete Pavement

2003 ◽  
Vol 1834 (1) ◽  
pp. 69-76 ◽  
Author(s):  
Prasada Rao Rangaraju
Keyword(s):  
High Performance ◽  
High Performance Concrete ◽  
Concrete Pavement ◽  
Performance Criteria ◽  
Test Results ◽  
Department Of Transportation ◽  
Performance Specifications ◽  
Concrete Materials ◽  
Practical Feasibility

In collaboration with FHWA, the Minnesota Department of Transportation (Mn/DOT) has successfully completed its first experimental high-performance concrete pavement (HPCP) project under the Testing and Evaluation Program (TE-30). This project is one of the 22 projects funded under the TE-30 Program. With a structural design life of 60 years, this HPCP is unique in that it incorporates significant changes to the existing Mn/DOT specifications on concrete materials. Some of the new materials-related specifications developed as a part of this project are based on performance criteria that influence long-term durability of the pavement structure. The background and considerations for selecting the new performance measures are discussed, and test results are presented that evaluate the practical feasibility of establishing and achieving the performance specifications.

The Fatigue Performance of High Performance Concrete Composite Girder

2019 ◽  
Author(s):  
C. Xu ◽  
B. Y. Zhang ◽  
Z. H. Hou
Keyword(s):  
High Performance ◽  
High Performance Concrete ◽  
Test Results ◽  
Normal Concrete ◽  
Bending Tests ◽  
Composite Girder ◽  
Tensile Performance ◽  
Negative Bending ◽  
The One ◽  
Push Out

<p>The application of high performance concrete has been increasingly concerned in the negative flexural region of steel‐concrete continuous composite girder because of its favorable tensile performance. However, the unclear cyclic and ultimate performance of a high performance concrete composite girder results to the problems which hinder the further application. In this case, a series of fatigue negative bending tests on HPC composite girders and fatigue push‐out tests on stud connectors in HPC were executed. The test results showed that the fatigue slip in the HPC composite girder was smaller than the normal concrete composite girder, and the fatigue life of stud in HPC was longer than the one in normal concrete. Meanwhile, according to the comparison between the stud fatigue live evaluations and test results, the AASHTO‐based evaluations were comparatively with larger safety redundancy, and JSCE was close to the test results but had smaller safety redundancy.</p>

scholarly journals On Flexural Performance of Girder-To-Girder Wet Joint for Lightweight Steel-UHPC Composite Bridge

2020 ◽  
Vol 10 (4) ◽  
pp. 1335 ◽  
Author(s):  
Shuwen Deng ◽  
Xudong Shao ◽  
Banfu Yan ◽  
Yan Wang ◽  
Huihui Li
Keyword(s):  
High Performance ◽  
High Performance Concrete ◽  
Bending Moment ◽  
Inhibitory Effect ◽  
Careful Consideration ◽  
Joint Interface ◽  
Test Results ◽  
Negative Moment ◽  
Composite Bridge ◽  
Negative Bending

Joints are always the focus of the precast structure for accelerated bridge construction. In this paper, a girder-to-girder joint suitable for steel-ultra-high-performance concrete (UHPC) lightweight composite bridge (LWCB) is proposed. Two flexural tests were conducted to verify the effectiveness of the proposed T-shaped girder-to-girder joint. The test results indicated that: (1) The T-shaped joint has a better cracking resistance than the traditional I-shaped joint; (2) The weak interfaces of the T-shaped joint are set in the areas with relatively lower negative bending moment, and thus the cracking risk could be decreased drastically; (3) The natural curing scheme for the joint is feasible, and the reinforcement has a very large inhibitory effect on the UHPC material shrinkage; The joint interface is the weak region of the LWCB, which requires careful consideration in future designs. Based on the experimental test results, the design and calculation methods for the deflection, crack width, and ultimate flexural capacity in the negative moment region of LWCB were presented.

Sign in / Sign up

Export Citation Format

Share Document