Outline of “Assessment Guideline for the Local Failure of Structures Subjected to Impact Actions” and “Safety Assessment of Concrete Structures Subjected to Explosion” by JSDFE

2018 ◽  
Vol 56 (10) ◽  
pp. 839-844
Author(s):  
M. Beppu ◽  
T. Morita ◽  
M. Nagata
Keyword(s):  
Safety Assessment ◽  
Concrete Structures ◽  
Local Failure

Crack Propagation and Local Failure Simulation of Reinforced Concrete Subjected to Projectile Impact Using RBSM

2016 ◽  
Author(s):  
Yoshihito Yamamoto ◽  
Soichiro Okazaki ◽  
Hikaru Nakamura ◽  
Masuhiro Beppu ◽  
Taiki Shibata
Keyword(s):  
Reinforced Concrete ◽  
Crack Propagation ◽  
High Velocity ◽  
Failure Modes ◽  
Concrete Structures ◽  
Constitutive Models ◽  
Local Failure ◽  
High Velocity Impact ◽  
Velocity Impact ◽  
Projectile Impact

In this paper, numerical simulations of reinforced mortar beams subjected to projectile impact are conducted by using the proposed 3-D Rigid-Body-Spring Model (RBSM) in order to investigate mechanisms of crack propagation and scabbing mode of concrete members under high-velocity impact. The RBSM is one of the discrete-type numerical methods, which represents a continuum material as an assemblage of rigid particle interconnected by springs. The RBSM have advantages in modeling localized and oriented phenomena, such as cracking, its propagation, frictional slip and so on, in concrete structures. The authors have already developed constitutive models for the 3D RBSM with random geometry generated Voronoi diagram in order to quantitatively evaluate the mechanical responses of concrete including softening and localization fractures, and have shown that the model can simulate cracking and various failure modes of reinforced concrete structures. In the target tests, projectile velocity is set 200m/s. The reinforced mortar beams with or without the shear reinforcing steel plates were used to investigate the effects of shear reinforcement on the crack propagation and the local failure modes. By comparing the numerical results with the test results, it is confirmed that the proposed model can reproduce well the crack propagation and the local failure behaviors. In addition, effects of the reinforcing plates on the stress wave and the crack propagation behaviors are discussed from the observation of the numerical simulation results. As a result, it was found that scabbing of reinforced mortar beams subjected to high velocity impact which is in the range of the tests is caused by mainly shear deformation of a beam.

Evolution of Sorption Properties in Large-Scale Concrete Structures Accounting for Long-Term Physical-Chemical Concrete Degradation

2011 ◽  
Author(s):  
Janez Perko ◽  
Diederik Jacques ◽  
Dirk Mallants ◽  
Suresh Seetharam
Keyword(s):  
Safety Assessment ◽  
Large Scale ◽  
Concrete Structures ◽  
Sorption Properties ◽  
Sorption Behaviour ◽  
Near Surface ◽  
Degradation Processes ◽  
Concrete Degradation ◽  
Engineered Barriers

Long-term safety of radioactive waste disposal facilities relies on the longevity of natural or engineered barriers designed to minimize the migration of contaminants from the facility into the environment. Especially near surface disposal facilities, such as planned by ONDRAF/NIRAS for the Dessel site in Belgium, long-term safety relies almost exclusively on the containment ability of the engineered barriers (EB) with concrete being the most important EB material used. Concrete is preferred over other materials mainly due to its favourable chemical properties resulting in a high chemical retention capacity, and owing to its good hydraulic isolation properties. However, due to the long time frames typically involved in safety assessment, the chemical, physical and mechanical properties of concrete evolve in time. The alterations in concrete mineralogy also cause changes in pH and sorption behaviour for many radionuclides during chemical degradation processes. Application of dynamic sorption of concrete requires an adequate knowledge of long-term concrete degradation processes, knowledge of the effect of changing mineralogy to sorption of radionuclides and knowledge of large-scale system behaviour over time. Moreover, when applied to safety assessment models, special attention is required to assure robustness and transparency of the implementation. The discussion in this paper focuses on the sorption properties of concrete; selection of data, rescaling issues and on the hypotheses used to build a robust and yet transparent dynamic model for large-scale concrete structures for assessing the long-term performance.

scholarly journals Concrete structures. Contribution to the safety assessment of existing structures

2015 ◽  
Vol 8 (3) ◽  
pp. 365-389
Author(s):  
D. COUTO ◽  
M. CARVALHO ◽  
A. CINTRA ◽  
P. HELENE
Keyword(s):  
Safety Assessment ◽  
Structural Engineering ◽  
Concrete Structures ◽  
Safety Evaluation ◽  
Design Stage ◽  
Design Phase ◽  
Safety Factors ◽  
Existing Structures ◽  
Partial Safety Factors ◽  
Existing Structure

The safety evaluation of an existing concrete structure differs from the design of new structures. The partial safety factors for actions and resistances adopted in the design phase consider uncertainties and inaccuracies related to the building processes of structures, variability of materials strength and numerical approximations of the calculation and design processes. However, when analyzing a finished structure, a large number of unknown factors during the design stage are already defined and can be measured, which justifies a change in the increasing factors of the actions or reduction factors of resistances. Therefore, it is understood that safety assessment in existing structures is more complex than introducing security when designing a new structure, because it requires inspection, testing, analysis and careful diagnose. Strong knowledge and security concepts in structural engineering are needed, as well as knowledge about the materials of construction employed, in order to identify, control and properly consider the variability of actions and resistances in the structure. With the intention of discussing this topic considered complex and diffuse, this paper presents an introduction to the safety of concrete structures, a synthesis of the recommended procedures by Brazilian standards and another codes, associated with the topic, as well a realistic example of the safety assessment of an existing structure.

Sign in / Sign up

Export Citation Format

Share Document