scholarly journals Optimization of HPLC Using Central Composite Design for Determination of Curcumin and Demethoxycurcumin in Tablet Dosage Form

2018 ◽  
Vol 16 (2) ◽  
pp. 137-145
Author(s):  
Chairany Siregar ◽  
Niken K Prabaningdyah ◽  
Syaiful Choiri ◽  
Sugeng Riyanto ◽  
Abdul Rohman

In this study, central composite design (CCD) was used for optimization of high performance liquid chromatographic (HPLC) method for simultaneous analysis of curcumin (CUR) and demethoxycurcumin (DMC) in tablets containing Curcuma extract. Separation of CUR and DMC was performed using X-Bridge C18 column (250 x 4.6 mm i.d; 5 μm). Four factors that were investigated include the concentration of acetic acid (X1), ratio of acetic acid (X2), flow rate of mobile phase (X3) and column temperature (X4). Based on responses obtained (retention time, peak area, resolution and tailing factor), the optimum condition selected was X1 = 3.00%, X2 = 51%, X3 = 1.05 mL/min and X4 = 45oC. This HPLC condition was validated by assessing several validation parameters including system suitability test, selectivity, linearity, precision, accuracy and robustness according to International Conference Harmonization (ICH). All validation parameters meet the acceptance criteria set by ICH. The validated method was successfully used for analysis of CUR and DMC in tablets containing Curcuma extract. CCD was effective means in optimization of HPLC for analysis of CUR and DMC in pharmaceutical formulation.Dhaka Univ. J. Pharm. Sci. 16(2): 137-145, 2017 (December)

INDIAN DRUGS ◽  
2015 ◽  
Vol 52 (11) ◽  
pp. 42-49
Author(s):  
C Dhal ◽  
◽  
F. J. Ahmad ◽  
M. Singhal ◽  
A. Kukrety ◽  
...  

An accurate, sensitive, precise, economic and rapid isocratic Reverse Phase High Performance Liquid Chromatography method was developed complying Quality by Design (QbD) trends and validated for determining doxycycline hyclate in bulk drug, tablet and capsule dosage form. The method was optimized using Minitab software with 3 factors (pH of the buffer, flow rate and percentage of buffer in the mobile phase), 2 level (higher limit and lower limit) Central Composite Design (CCD). The results of randomized 20 runs were analyzed for optimum composite desirability to give optimum conditions such as, pH 6.5, flow rate 0.9 mLmin-1 and 30:70 V/V 0.05M potassium dihydrogen orthophosphate buffer adjusted to pH 6.5 using orthophosphoric acid and methanol using C8 column 250 X 4.6 mm X 5.0 μm, injection volume of 10uL, ambient column temperature and ultraviolet detection using photo diode array detector at 360nm as constants. The method was validated as per ICH guidelines and was found linear over a concentration range of 10-100 μg/mL (r2 = 0.999) with the limits of detection and quantification being 2.45 μg/mL and 7.55 μg/mL respectively.


2012 ◽  
Vol 1 (8) ◽  
pp. 193-198 ◽  
Author(s):  
Chusena Narasimharaju Bhimanadhuni ◽  
Devala Rao Garikapati ◽  
Pasupuleti Usha

A Simple, efficient and reproducible reverse phase high performance liquid chromatographic method was developed and validated for the Simultaneous determination of Escitalopram oxalate and Clonazepam in combined dosage form. The separation was effected on a Hypersil ODS C18 column (250mm X 4.6mm; 5µ) using a mobile phase mixture of buffer and acetonitrile in a ratio of 50:50 v/v at a flow rate of 1.0ml/min. The detection was made at 240nm. The retention time of Escitalopram oxalate and Clonazepam was found to be 2.840± 0.007min and 4.007±0.006 min. Calibration curve was linear over the concentration range of 20-120µg/ml and 1-6µg/ml for Escitalopram oxalate and Clonazepam. All the analytical validation parameters were determined and found in the limit as per ICH guidelines, which indicates the validity of the method. The developed method is also found to be precise, accurate, specific, robust and rapid for the simultaneous determination of Escitalopram oxalate and Clonazepam in tablet dosage forms.DOI: http://dx.doi.org/10.3329/icpj.v1i8.11249 International Current Pharmaceutical Journal 2012, 1(8): 193-198 


Author(s):  
R Vijay Amirtharaj ◽  
S Lavanya

A simple, sensitive, precise, selective reverse phase high performance liquid chromatographic method was developed and validated for erlotinib hydrochloride in tablet dosage form.(0.02M)The separation was achieved on C18 column (150mm×4.6mm.i.d.,5.0μm) using potassium dihydrogen phosphate: acetonitrile in the ratio 50:50v/v as mobile phase having pH 4.5 was adjusted with methanol and flow rate 1ml/min. Detection was carried out using a UV detector at 248nm. The column temperature was adjusted at 30ᵒC. The method was validated for precision, linearity and range, stability and robustness. The developed and validated method was successfully applied for the quantitative analysis of ERLONAT tablets. The total chromatographic analysis time per sample was about 7min with Erlotinib eluting at 6.547min.Validation studies demonstrated that this HPLC method is simple, specific, rapid, reliable and reproducible. The standard curves were linear over the concentration ranges, 88.32- 132.48μg/ml for erlotinib. The high recovery confirms the suitability of the proposed method for the determination of Erlotinib in ERLONAT tablets. The results of analysis have been validated according to ICH guideline requirements. The method can be applied for Erlotinib hydrochloride tablets.


INDIAN DRUGS ◽  
2019 ◽  
Vol 56 (03) ◽  
pp. 39-45
Author(s):  
A Sherje ◽  
A. Sonalkar ◽  

A reversed-phase high-performance liquid chromatographic method was developed for the simultaneous determination of olmesartan medoxomil (OLME) and chlorthalidone (CHLOR) in tablet dosage form. The analysis was performed on Inertsil ODS C18 (250 x 4.6 mm, 5 μ) using KH2PO4 phosphate buffer (pH) and acetonitrile as mobile phase in the proportion of 60: 40 v/v at flow rate of 1.0 mL/min. Detection of drugs was carried out in isocratic mode using UV detector at 275 nm. The retention time of OLME and CHLOR was 13.9 ± 0.1 min. and 4.4 ± 0.5 min., respectively and the total run time was 20 min. The method was validated according to the requirements of the United States Pharmacopeia. The percentage recoveries was found to be in the range of 98.9 - 100.7%. The method was successfully applied to the assay of OLME and CHLOR in tablet dosage form.


2021 ◽  
Vol 23 (06) ◽  
pp. 992-1000
Author(s):  
Sneha S. Ghule ◽  
◽  
Ashpak M. Tamboli ◽  
Snehal D. Patil ◽  
◽  
...  

A reverse-phase high-performance liquid chromatography (RP-HPLC) method for the simultaneous estimation of Pyridoxamine dihydrochloride and Acetylcysteine in the marketed formulation is developed. Chromatography carried out at 30oc temperature on Agilent Zorbax Bonus-RP (250 x 4.6 mm, 5 µ) coloum. Coloum using a mobile phase 0.1% trifluroacetic acid in water: acetonitrile (80:20v/v) with flow rate 1ml/min (DAD scan at 210nm). Validation parameters such as system suitability, linearity, precision, accuracy are considered as reported International Conference on Harmonization guidelines. The retention times for Pyridoxamine dihydrochloride and Acetylcysteine are 2 min and 3.4 min. The linearity range for Pyridoxamine dihydrochloride and Acetylcysteine is 30-70 µg/ml and 180-420 µg/ml. The %RSD for accuracy was found to be less than 2%. Hence the proposed method was found to be accurate, precise, reproducible, and specific and can be used for simultaneous analysis of these drugs in tablet formulation.


INDIAN DRUGS ◽  
2018 ◽  
Vol 55 (06) ◽  
pp. 63-68
Author(s):  
R. Raut ◽  
◽  
A. Patil ◽  
V. K Munipalli ◽  
M. Patel ◽  
...  

A simple precise and rapid Reverse Phase High Performance Liquid Chromatographic (RP-HPLC) method has been developed for quantitative determination of Regorafenib in tablet dosage form. In this method Hypersil Gold (C18, 150mm× 4.6mm id, 3μ) column with mobile phase consisting of Trifluoroacetic acid (0.2% v/v) and Acetonitrile in the ratio of (50: 50 v/v) at 400C in an isocratic mode was used. The detection was carried out at 260 nm and 20μL injection volume was selected with the flow rate 1mL/min. The linearity range of Regorafenib shows concentration between 5-200 μg/mL. The regression coefficient obtained was 0.999. Retention time of Regorafenib was found to be 6.49 minutes. Acetonitrile and Water in the ratio of (3:1) was used as a diluent. The method was validated as per ICH guidelines and is simple, fast, accurate, precise and can be applied for routine quality control analysis of Regorafenib in tablet dosage form.


INDIAN DRUGS ◽  
2015 ◽  
Vol 52 (08) ◽  
pp. 12-16
Author(s):  
S Vidyadhara ◽  
◽  
L. S Reddyvalam ◽  
T. Koduri ◽  
P. K. Borra ◽  
...  

A simple, accurate, precise high-performance liquid chromatographic (HPLC) method has been developed and validated for the simultaneous determination of abacavir sulphate (ABA) and lamivudine (LAM) in combined dosage form. Separation was performed on a C18 column [Agilent ODS UG 5 column, 250 mm x 4.5 mm], with methanol: water (50:50 V/V) isocratic elution using a flow rate of 1mL/min. Good sensitivity was observed with UV detection at 277 nm. After method development, the interference of other active compounds and excipients, repeatability and linearity, were investigated. Retention times of LAM and ABA were found to be 3.3 and 6.3 min, respectively. The method was validated over the range from 2.5-12.5 μg/mL for LAM and 5-25 μg/mL for ABA with correlation coefficients of 0.9997 and 0.9996, respectively. This method was shown to be accurate, robust, selective, linear, and repeatable and can be successfully employed in routine quality control for the simultaneous analysis of ABA and LAM in tablets.


2008 ◽  
Vol 91 (4) ◽  
pp. 739-743 ◽  
Author(s):  
Andréia de Haro Moreno ◽  
Hérida Regina Nunes Salgado

Abstract A rapid, accurate, and sensitive high-performance liquid chromatographic (HPLC) method was developed and validated for the determination of ceftazidime in pharmaceuticals. The method validation parameters yielded good results and included range, linearity, precision, accuracy, specificity, and recovery. The excipients in the commercial powder for injection did not interfere with the assay. Reversed-phase chromatography was used for the HPLC separation on a Waters C18 (WAT 054275; Milford, MA) column with methanolwater (70 + 30, v/v) as the mobile phase pumped isocratically at a flow rate of 1.0 mL/min. The effluent was monitored at 245 nm. The calibration graph for ceftazidime was linear from 50.0 to 300.0 g/mL. The values for interday and intraday precision (relative standard deviation) were <1. The results obtained by the HPLC method were calculated statistically by analysis of variance. We concluded that the HPLC method is satisfactory for the determination of ceftazidime in the raw material and pharmaceuticals.


2008 ◽  
Vol 91 (2) ◽  
pp. 387-391 ◽  
Author(s):  
Jaeho Ha ◽  
Kyu-Jai Han ◽  
Ki-Jin Kim ◽  
Seung-Weon Jeong

Abstract A sensitive, precise, and specific gas chromatographic (GC) method was developed for the analysis of capsaicin in Gochujang and validated by comparing with a column high-performance liquid chromatographic (HPLC) method (AOAC 995.03). The method validation parameters yielded good results, including linearity, precision, accuracy, and recovery. The GC separation was performed on a (5 phenyl)-methylpolysiloxane column [length 30 m, internal diameter (id) 250 μm, film thickness 0.25 μm] followed by flame ionization detection. The conditions of temperature programming were initially 220Cfor 1min, rampat5C/minto270C, and hold for 10 min. The recovery of capsaicin in Gochujang was more than 92, and the detection limit and lower determination limit of the GC analysis were 1.0 and 5.0 μg/g, respectively. The calibration graph for capsaicin was linear from 1 to 250 μg/mL for GC and 0.5 to 50 μg/mL for HPLC. The interday and intraday precisions (relative standard deviations) were <4.02.


2013 ◽  
Vol 57 (2) ◽  
pp. 37-44 ◽  
Author(s):  
Ghasem Haghi ◽  
Alireza Hatami ◽  
Mehdi Mehran

Abstract A reverse-phase high-performance liquid chromatographic (RP -HPLC ) method was developed and validated for the analysis of honeybee venom samples and drug products containing honeybee venom. The validation parameters were linearity, sensitivity, precision, and recovery. Melittin is the main component of honeybee venom was extracted with pure water, and then evaluated by RP -HPLC with a photodiode array (PDA ) detector. Separation of the samples was achieved on a Europa Protein C18 column with linear gradient elution of acetonitrile and 0.4% phosphoric acid at 25°C. There was a flow rate of 1 mL/min. Detection was set at 220 nm. Limits of detection (LOD ) and quantification (LO Q) for melittin were 1.1 and 3.2 μg/mL, respectively. The amount of melittin in honeybee venom samples ranged from 21.9 to 66.4 %.


Sign in / Sign up

Export Citation Format

Share Document