scholarly journals Stress distribution in prosthetic abutments: a finite element analysis comparison of conical and UCLA abutments

2021 ◽  
Vol 10 (13) ◽  
pp. e445101321461
Author(s):  
Cristiano Garcia Araújo ◽  
Milton Edson Miranda ◽  
Caroline Dini ◽  
Gabrielle Alencar Ferreira Silva ◽  
Karina Andrea Novaes Olivieri
Keyword(s):  
Finite Element ◽  
Stress Distribution ◽  
Principal Stress ◽  
Qualitative Description ◽  
Von Mises Stress ◽  
Medullary Bone ◽  
Retention System ◽  
Single Crown ◽  
Mandibular Molar ◽  
Monolithic Zirconia

The effect of prosthetic abutment type on single-screwed prostheses in posterior mandibular molar rehabilitations is not yet known. Thus, the aim of this study was to evaluate the distribution of stresses in the crowns, prosthetic components, implant and bone in implant-supported restorations with or without a prosthetic abutment, maintaining an equal total height of the implant-crown set. Virtual 3-dimensional (3D) finite element models were constructed, the models were designed to represent a posterior single crown rehabilitation with a screwed retention system and external hexagon implants placed in the lower first molar region. Two rehabilitation methods were designed to simulate a monolithic zirconia crown screwed onto a conical abutment, which was screwed onto an external hexagon implant (M1); and a monolithic zirconia crown screwed directly onto the external hexagon implant using an UCLA abutment (M2). An axial load of 200 N was simulated and applied axially in the occlusal region of the restoration divided into 5 points. The quantitative and qualitative description of the maximum principal stress for crowns, von Mises stress for screws, conical abutment and implant; and minimal principal stress for cortical and medullary bone were evaluated. M1 presented similar stress distribution for crowns, cortical and medullary bone compared to M2. Conversely, the stress values were considerably higher for crowns screw and implants in the M2 group. In conclusion, single implant-supported rehabilitations of mandibular first molars using external hexagon implants presented better stress distribution on the crown screw and implants for the M1 group compared to M2.

scholarly journals THREE-DIMENSIONAL FINITE ELEMENT ANALYSIS OF CLASS 2 INLAY ON MANDIBULAR MOLAR USING VARIOUS MATERIALS

2018 ◽  
Vol 6 (7) ◽  
pp. 272-277
Author(s):  
Maj Pankaj Awasthi ◽  
Lt Col Sonali Sharma ◽  
Maj Summerdeep Kaur
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Distribution ◽  
Stress Analysis ◽  
Von Mises Stress ◽  
Element Analysis ◽  
Tooth Structure ◽  
Mandibular Molar ◽  
Von Mises ◽  
Mandibular First Molar

Aim: To study the stress distribution in Class 2 Inlay of various materials on Mandibular Molar. Background: Inlays are fabricated using different materials like gold, porcelain or a cast metal alloy. Difference in the modulus of elasticity of the material and tooth structure would lead to generation of stresses leading to failure of the restoration or loss of tooth structure. Finite Element Analysis (FEA) is a mathematical tool for stress analysis in a structure. Von Mises stress being the combination of normal and shear stresses which occur in all directions. This stress has to be given diligent importance while considering the type and material of restoration to achieve long-term success. Methodology: In our study, stress analysis was performed on the mandibular first molar using a stress analysis software (ANSYS). A computer model of mandibular first molar was generated along with generation of an inlay volume using a FEA software preprocessor. The models with the class 2 inlays of different materials were subjected to 350N and 800N load simulating normal masticatory force and bruxism respectively. Maximum and minimum stresses were calculated for each model separately. Results: Von Mises stress distribution for different materials for normal masticatory forces and bruxism were studied and evaluated. Conclusion: The study revealed the maximum and minimum stresses imposed over the tooth and the restoration and provides insight into the areas which are more prone to fracture under the occlusal load.

scholarly journals Different bone anchorages for Morse taper implants with different lengths in maxilla anterior: An in silico analysis

2021 ◽  
Vol 10 (9) ◽  
pp. e57010917729
Author(s):  
Hiskell Fernandes Fernandes e Oliveira ◽  
Cleidiel Araujo Lemos ◽  
Ronaldo Silva Cruz ◽  
Victor Eduardo de Souza Batista ◽  
Rodrigo Capalbo da Silva ◽  
...  
Keyword(s):  
Finite Element ◽  
Stress Distribution ◽  
Bone Tissue ◽  
3D Models ◽  
Von Mises Stress ◽  
Bone Block ◽  
Apical Region ◽  
Biomechanical Behavior ◽  
Single Crown ◽  
Nasal Floor

This study aimed to evaluate the stress distribution in bone tissue, in Morse tapper implants and components supporting a single crown in the maxillary anterior area, under different bone anchorages (conventional, bicortical and bicortical with nasal floor elevation) and implant lengths (8.5 mm, 10 mm and 11.5 mm) using 3D finite element analyses. Three 3D models including element #11 were simulated using software InVesalius, Rhinoceros 3D and SolidWorks. Bone block models were reconstructed from computed tomography and simulated the placement of one implant of 4 mm of diameter and lengths above mentioned, supporting cemented zirconia crown. The 3D models were processed by the finite element FEMAP and NeiNastran software, using a load of 178N were applied at 0º, 30º and 60º, considering the implant long axis. Results were visualized as the von Mises stress, maximum principal stress and microstrain maps. Bicortical bone anchorages showed lower stress and microstrain bone tissue when compared to conventional bone anchorage. However, no differences were observed between bicortical and nasal floor elevation. Regarding implants and components, the stress distribution was similar between models with little stress relief in the apical region of the implants for implants with conventional anchorage. The conclusion drawn from this study is that non-axial loading showed worse biomechanical behavior for bone tissue and implants/components. The bicortical techniques (bicortical and nasal floor elevation) should be preferred during the implant placement to reduce the stress and microstrain in the bone tissue.

Effect of supporting implants inclination on stability of fixed partial denture: A finite element study

2020 ◽  
Vol 234 (10) ◽  
pp. 1162-1171
Author(s):  
Amel Boukhlif ◽  
Ali Merdji ◽  
Sandipan Roy ◽  
Hashem Alkhaldi ◽  
Ibrahim Abu-Alshaikh ◽  
...  
Keyword(s):  
Finite Element ◽  
Stress Distribution ◽  
Peak Stress ◽  
Von Mises Stress ◽  
Favorable Effect ◽  
Partial Denture ◽  
Finite Element Study ◽  
Fixed Partial Denture ◽  
Mandibular Molar ◽  
Element Study

The aim of this finite element study was to analyze effect of supporting implants inclination on stress distribution in the bone for a four-unit fixed partial denture. A three-dimensional finite element model of mandibular molar section of the bone to receive implants was constructed. Three implant-supported fixed partial dentures, with null, moderate and wide tilting, of 0°, 15° and 30° implant inclinations, respectively, were modeled. A mechanical load of 10 MPa was applied in coronal–apical direction on bridge framework at the regions of crowns positions. The finite element analysis was performed, and von Mises stress levels were calculated. Peak stress concentration in the cortical bone was observed mostly around the implant necks, in inter-implants line. There was favorable stress distribution during loading, with peak stress being 90.04 MPa for 0°, which decreased to 54.33 MPa for 15° and 46.36 MPa for 30° inclination. The supporting implants inclination in fixed partial denture plays an important role in stress distribution and may be helpful in preventing bone loss and implant failure. This phenomenon is likely to be more pronounced in bones of poor quality. Within the limitation of this study, it seems that the inclination of implants in fixed partial denture has a favorable effect on stress distribution pattern values around the supporting implants.

scholarly journals Biomechanical assessment of different fixation methods in mandibular high sagittal oblique osteotomy using a three-dimensional finite element analysis model

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Charles Savoldelli ◽  
Elodie Ehrmann ◽  
Yannick Tillier
Keyword(s):  
Finite Element ◽  
Stress Distribution ◽  
Three Dimensional ◽  
Von Mises Stress ◽  
Analysis Model ◽  
Element Analysis ◽  
Fixation Methods ◽  
Oblique Osteotomy ◽  
Von Mises

AbstractWith modern-day technical advances, high sagittal oblique osteotomy (HSOO) of the mandible was recently described as an alternative to bilateral sagittal split osteotomy for the correction of mandibular skeletal deformities. However, neither in vitro nor numerical biomechanical assessments have evaluated the performance of fixation methods in HSOO. The aim of this study was to compare the biomechanical characteristics and stress distribution in bone and osteosynthesis fixations when using different designs and placing configurations, in order to determine a favourable plating method. We established two finite element models of HSOO with advancement (T1) and set-back (T2) movements of the mandible. Six different configurations of fixation of the ramus, progressively loaded by a constant force, were assessed for each model. The von Mises stress distribution in fixations and in bone, and bony segment displacement, were analysed. The lowest mechanical stresses and minimal gradient of displacement between the proximal and distal bony segments were detected in the combined one-third anterior- and posterior-positioned double mini-plate T1 and T2 models. This suggests that the appropriate method to correct mandibular deformities in HSOO surgery is with use of double mini-plates positioned in the anterior one-third and posterior one-third between the bony segments of the ramus.

scholarly journals Influence of fibromucosa height and loading on the stress distribution of a total prosthesis: a finite element analysis

2021 ◽  
Vol 24 (2) ◽  
Author(s):  
Tarcisio José de Arruda Paes Junior ◽  
João Paulo Mendes Tribst ◽  
Amanda Maria de Oliveira Dal Piva ◽  
Viviane Maria Gonçalves de Figueiredo ◽  
Alexandre Luiz Souto Borges ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Distribution ◽  
Cortical Bone ◽  
Principal Stress ◽  
Maximum Principal Stress ◽  
Element Analysis ◽  
Total Displacement ◽  
Anterior Guidance ◽  
Mandibular Movements

Purpose: To evaluate the effect of fibromucosa height on the stress distribution and displacement of mandibular total prostheses during posterior unilateral load, posterior bilateral load and anterior guidance using the finite element analysis (FEA). Material and methods: 3D virtual models were made to simulate the stress generated during different mandibular movements in a total prosthesis. The contacts were simulated according to the physiology, being considered perfectly bonded between cortical and medullar bones; and between cortical bone and mucosa. Non-linear frictional contact was used for the total prosthesis base and fibromucosa, allowing the prosthesis to slide over the tissue. The cortical bone base was fixed and the 100 N load was applied as unilateral load, posterior bilateral load and anterior guidance simulation. The required results were for maximum principal stress (MPa), microstrain (mm/mm) and total displacement (mm). The numerical results were converted into colorimetric maps and arranged according to corresponding scales. Results: The stress generated in all situations was directly proportional to the fibromucosa height. The maximum principal stress results demonstrated greater magnitude for anterior guidance, posterior unilateral and posterior bilateral, respectively. Only posterior unilateral load demonstrated an increase in bone microstrain, regardless of the fibromucosa height. Prosthesis displacement was lower under posterior bilateral loading. Conclusion: Posterior bilateral loading is indicated for total prosthesis because it allows lower prosthesis displacement, lower stress concentration at the base of the prosthesis and less bone microstrain.   Keywords Finite element analysis; Occlusion; Total prosthesis.

scholarly journals Force Transfer and Stress Distribution in an Implant-Supported Overdenture Retained with a Hader Bar Attachment: A Finite Element Analysis

2013 ◽  
Vol 2013 ◽  
pp. 1-12 ◽  
Author(s):  
Preeti Satheesh Kumar ◽  
Kumar K. S. Satheesh ◽  
Jins John ◽  
Geetha Patil ◽  
Ruchi Patel
Keyword(s):  
Finite Element ◽  
Stress Concentration ◽  
Stress Distribution ◽  
Maximum Stress ◽  
Alveolar Bone ◽  
Von Mises Stress ◽  
Element Analysis ◽  
Finite Element Software ◽  
Force Transfer ◽  
Edentulous Mandible

Background and Objectives. A key factor for the long-term function of a dental implant is the manner in which stresses are transferred to the surrounding bone. The effect of adding a stiffener to the tissue side of the Hader bar helps to reduce the transmission of the stresses to the alveolar bone. But the ideal thickness of the stiffener to be attached to the bar is a subject of much debate. This study aims to analyze the force transfer and stress distribution of an implant-supported overdenture with a Hader bar attachment. The stiffener of the bar attachments was varied and the stress distribution to the bone around the implant was studied. Methods. A CT scan of edentulous mandible was used and three models with 1, 2, and 3 mm thick stiffeners were created and subjected to loads of emulating the masticatory forces. These different models were analyzed by the Finite Element Software (Ansys, Version 8.0) using von Mises stress analysis. Results. The results showed that the maximum stress concentration was seen in the neck of the implant for models A and B. In model C the maximum stress concentration was in the bar attachment making it the model with the best stress distribution, as far as implant failures are concerned. Conclusion. The implant with Hader bar attachment with a 3 mm stiffener is the best in terms of stress distribution, where the stress is concentrated at the bar and stiffener regions.

scholarly journals Effect of Fiber Posts on Stress Distribution of Endodontically Treated Upper Premolars: Finite Element Analysis

Nanomaterials ◽  
2020 ◽  
Vol 10 (9) ◽  
pp. 1708 ◽  
Author(s):  
Maciej Zarow ◽  
Mirco Vadini ◽  
Agnieszka Chojnacka-Brozek ◽  
Katarzyna Szczeklik ◽  
Grzegorz Milewski ◽  
...  
Keyword(s):  
Finite Element ◽  
Stress Distribution ◽  
Resin Composite ◽  
Von Mises Stress ◽  
Stress Distributions ◽  
Stress Concentrations ◽  
Element Analysis ◽  
Endodontically Treated Tooth ◽  
Maxillary Premolars ◽  
Von Mises

By means of a finite element method (FEM), the present study evaluated the effect of fiber post (FP) placement on the stress distribution occurring in endodontically treated upper first premolars (UFPs) with mesial–occlusal–distal (MOD) nanohybrid composite restorations under subcritical static load. FEM models were created to simulate four different clinical situations involving endodontically treated UFPs with MOD cavities restored with one of the following: composite resin; composite and one FP in the palatal root; composite and one FP in the buccal root; or composite and two FPs. As control, the model of an intact UFP was included. A simulated load of 150 N was applied. Stress distribution was observed on each model surface, on the mid buccal–palatal plane, and on two horizontal planes (at cervical and root-furcation levels); the maximum Von Mises stress values were calculated. All analyses were replicated three times, using the mechanical parameters from three different nanohybrid resin composite restorative materials. In the presence of FPs, the maximum stress values recorded on dentin (in cervical and root-furcation areas) appeared slightly reduced, compared to the endodontically treated tooth restored with no post; in the same areas, the overall Von Mises maps revealed more favorable stress distributions. FPs in maxillary premolars with MOD cavities can lead to a positive redistribution of potentially dangerous stress concentrations away from the cervical and the root-furcation dentin.

scholarly journals A Comparative Three-Dimensional Finite Element Study of Two Space Regainers in the Mixed Dentition Stage

2020 ◽  
Vol 14 (01) ◽  
pp. 107-114
Author(s):  
Mohamed Ahmed Abdel Hakim ◽  
Nagwa Mohamed Ali Khatab ◽  
Kareem Maher Gaber Mohamed ◽  
Ahmad Abdel Hamid Elheeny
Keyword(s):  
Finite Element ◽  
Stress Distribution ◽  
Three Dimensional ◽  
The Other ◽  
Mixed Dentition ◽  
Von Mises Stress ◽  
Stress Concentrations ◽  
Permanent Molar ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element

Abstract Objectives This study aims to compare the stress distribution and displacement that resulted from the use of a Gerber space regainer and sagittal distalizer using three-dimensional finite element analysis. Materials and Methods Three-dimensional simulated models of the appliances were developed using a software. The forces applied by the two appliances were 3N (tipping) and 15N (bodily), respectively. Displacement and von Mises stress on the compact and cancellous bone, periodontal ligament (PDL), crowns of the mandibular first, second permanent molars, and deciduous canines were calculated. Stress distribution and displacement values were measured via linear static analysis. Results Gerber space regainer showed greater displacement than that produced by the sagittal distalizer at the first permanent molar. However, such displacement was less at the other tested points when compared with that delivered by sagittal distalizer. The stresses created by Gerber appliance were higher in the crown and PDL of the deciduous canine than the crown of the first permanent molar crown. Conclusions Gerber appliance generates more distal force and less stress concentration on the crown of the mandibular first permanent molar than that created by the sagittal distalizer. On the other hand, stress concentrations produced by Gerber space regainer are found to be more on the crown and PDL of the deciduous canine. Therefore, it can be concluded that the use of Gerber appliance needs more anchorage.

The function(s) of bone ornamentation in the crocodylomorph osteoderms: a biomechanical model based on a finite element analysis

Paleobiology ◽  
2019 ◽  
Vol 45 (1) ◽  
pp. 182-200 ◽  
Author(s):  
François Clarac ◽  
Florent Goussard ◽  
Vivian de Buffrénil ◽  
Vittorio Sansalone
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Distribution ◽  
Von Mises Stress ◽  
Late Triassic ◽  
Mechanical Resistance ◽  
Apical Surface ◽  
Element Analysis ◽  
Physiological Functions ◽  
Von Mises

AbstractThis paper aims at assessing the influence of the bone ornamentation and, specifically, the associated loss of bone mass on the mechanical response of the crocodylomorph osteoderms. To this end, we have performed three-dimensional (3D) modeling and a finite element analysis on a sample that includes both extant dry bones and well-preserved fossils tracing back to the Late Triassic. We simulated an external attack under various angles on the apical surface of each osteoderm and further repeated the simulation on an equivalent set of smoothed 3D-modeled osteoderms. The comparative results indicated that the presence of an apical sculpture has no significant influence on the von Mises stress distribution in the osteoderm volume, although it produces a slight increase in its numerical score. Moreover, performing parametric analyses, we showed that the Young's modulus of the osteoderm, which may vary depending on the bone porosity, the collagen fiber orientation, or the calcification density, has no impact on the von Mises stress distribution inside the osteoderm volume. As the crocodylomorph bone ornamentation is continuously remodeled by pit resorption and secondary bone deposition, we assume that the apical sculpture may be the outcome of a trade-off between the bone mechanical resistance and the involvement in physiological functions. These physiological functions are indeed based on the setup of a bone superficial vessel network and/or the recurrent release of mineral elements into the plasma: heat transfers during basking and respiratory acidosis buffering during prolonged apnea in neosuchians and teleosaurids; compensatory homeostasis in response to general calcium deficiencies. On a general morphological basis, the osteoderm geometric variability within our sample leads us to assess that the global osteoderm geometry (whether square or rectangular) does not influence the von Mises stress, whereas the presence of a dorsal keel would somewhat reduce the stress along the vertical axis.

scholarly journals A three - dimensional finite element study on the stress distribution pattern of two prosthetic abutments for external hexagon implants

2013 ◽  
Vol 07 (04) ◽  
pp. 484-491 ◽  
Author(s):  
Wagner Moreira ◽  
Caio Hermann ◽  
Jucélio Tomás Pereira ◽  
Jean Anacleto Balbinoti ◽  
Rodrigo Tiossi
Keyword(s):  
Finite Element ◽  
Stress Distribution ◽  
Three Dimensional ◽  
Von Mises Stress ◽  
Element Analysis ◽  
Dimensional Finite Element ◽  
3D Fea ◽  
The One ◽  
Von Mises ◽  
Three Dimensional Finite Element

ABSTRACT Objective: The purpose of this study was to evaluate the mechanical behavior of two different straight prosthetic abutments (one- and two-piece) for external hex butt-joint connection implants using three-dimensional finite element analysis (3D-FEA). Materials and Methods: Two 3D-FEA models were designed, one for the two-piece prosthetic abutment (2 mm in height, two-piece mini-conical abutment, Neodent) and another one for the one-piece abutment (2 mm in height, Slim Fit one-piece mini-conical abutment, Neodent), with their corresponding screws and implants (Titamax Ti, 3.75 diameter by 13 mm in length, Neodent). The model simulated the single restoration of a lower premolar using data from a computerized tomography of a mandible. The preload (20 N) after torque application for installation of the abutment and an occlusal loading were simulated. The occlusal load was simulated using average physiological bite force and direction (114.6 N in the axial direction, 17.1 N in the lingual direction and 23.4 N toward the mesial at an angle of 75° to the occlusal plan). Results: The regions with the highest von Mises stress results were at the bottom of the initial two threads of both prosthetic abutments that were tested. The one-piece prosthetic abutment presented a more homogeneous behavior of stress distribution when compared with the two-piece abutment. Conclusions: Under the simulated chewing loads, the von Mises stresses for both tested prosthetic-abutments were within the tensile strength values of the materials analyzed which thus supports the clinical use of both prosthetic abutments.

Sign in / Sign up

Export Citation Format

Share Document