scholarly journals Optimal Harmonic Mitigation in Distribution Systems with Inverter Based Distributed Generation

2021 ◽  
Vol 11 (2) ◽  
pp. 774 ◽  
Author(s):  
Ahmed S. Abbas ◽  
Ragab A. El-Sehiemy ◽  
Adel Abou El-Ela ◽  
Eman Salah Ali ◽  
Karar Mahmoud ◽  
...  
Keyword(s):  
Power Quality ◽  
Distributed Generation ◽  
Distribution System ◽  
Distribution Systems ◽  
Renewable Energy Sources ◽  
Harmonic Distortion ◽  
Planning Problem ◽  
Voltage Profile ◽  
Harmonic Mitigation ◽  
The Impact

In recent years, with the widespread use of non-linear loads power electronic devices associated with the penetration of various renewable energy sources, the distribution system is highly affected by harmonic distortion caused by these sources. Moreover, the inverter-based distributed generation units (DGs) (e.g., photovoltaic (PV) and wind turbine) that are integrated into the distribution systems, are considered as significant harmonic sources of severe harmful effects on the system power quality. To solve these issues, this paper proposes a harmonic mitigation method for improving the power quality problems in distribution systems. Specifically, the proposed optimal planning of the single tuned harmonic filters (STFs) in the presence of inverter-based DGs is developed by the recent Water Cycle Algorithm (WCA). The objectives of this planning problem aim to minimize the total harmonic distortion (THD), power loss, filter investment cost, and improvement of voltage profile considering different constraints to meet the IEEE 519 standard. Further, the impact of the inverter-based DGs on the system harmonics is studied. Two cases are considered to find the effect of the DGs harmonic spectrum on the system distortion and filter planning. The proposed method is tested on the IEEE 69-bus distribution system. The effectiveness of the proposed planning model is demonstrated where significant reductions in the harmonic distortion are accomplished.

scholarly journals The Impact of Connecting Distributed Generation to the Distribution System

10.14311/986 ◽  
2007 ◽  
Vol 47 (4-5) ◽  
Author(s):  
E. V. Mgaya ◽  
Z. Müller
Keyword(s):  
Renewable Energy ◽  
Distributed Generation ◽  
Distribution System ◽  
Renewable Energy Sources ◽  
Electric Energy ◽  
Reducing Power ◽  
Effective Capacity ◽  
Voltage Profile ◽  
The Impact

This paper deals with the general problem of utilizing of renewable energy sources to generate electric energy. Recent advances in renewable energy power generation technologies, e.g., wind and photovoltaic (PV) technologies, have led to increased interest in the application of these generation devices as distributed generation (DG) units. This paper presents the results of an investigation into possible improvements in the system voltage profile and reduction of system losses when adding wind power DG (wind-DG) to a distribution system. Simulation results are given for a case study, and these show that properly sized wind DGs, placed at carefully selected sites near key distribution substations, could be very effective in improving the distribution system voltage profile and reducing power losses, and hence could  improve the effective capacity of the system. 

Impact of Distributed Generation on Voltage Profile in Radial Feeder

2017 ◽  
Vol 6 (3) ◽  
pp. 583 ◽  
Author(s):  
Charles R. Sarimuthu ◽  
Vigna K. Ramachandaramurthy ◽  
H. Mokhlis ◽  
K.R. Agileswari
Keyword(s):  
Distributed Generation ◽  
Radial Distribution ◽  
Distribution System ◽  
Distribution Systems ◽  
Voltage Drop ◽  
Green Energy ◽  
Simulation Software ◽  
Voltage Profile ◽  
Distribution Feeder ◽  
The Impact

The use of distributed generation (DG) within distribution systems has increased for the last two decades due to worldwide increase in demand for electricity and governmental policy change from “conventional” energy to “green” energy. High levels of penetration of DG have many significant benefits but also come with many drawbacks such as voltage drop and power losses. This study presents the impact of DG at different locations in a distribution feeder in terms of the feeder voltage profile. A radial distribution system is simulated using PSCAD/EMTDC simulation software while changing the size and location of DG in the system. The obtained results are used for better understanding on the impact of DG on voltage profile in radial distribution feeder.

scholarly journals A new meta-heuristic pathfinder algorithm for solving optimal allocation of solar photovoltaic system in multi-lateral distribution system for improving resilience

2021 ◽  
Vol 3 (1) ◽  
Author(s):  
Varaprasad Janamala
Keyword(s):  
Distribution System ◽  
Distribution Systems ◽  
Voltage Stability ◽  
Optimal Allocation ◽  
Photovoltaic System ◽  
Solar Photovoltaic ◽  
Voltage Profile ◽  
Pv System ◽  
Solar Photovoltaic System ◽  
The Impact

AbstractA new meta-heuristic Pathfinder Algorithm (PFA) is adopted in this paper for optimal allocation and simultaneous integration of a solar photovoltaic system among multi-laterals, called interline-photovoltaic (I-PV) system. At first, the performance of PFA is evaluated by solving the optimal allocation of distribution generation problem in IEEE 33- and 69-bus systems for loss minimization. The obtained results show that the performance of proposed PFA is superior to PSO, TLBO, CSA, and GOA and other approaches cited in literature. The comparison of different performance measures of 50 independent trail runs predominantly shows the effectiveness of PFA and its efficiency for global optima. Subsequently, PFA is implemented for determining the optimal I-PV configuration considering the resilience without compromising the various operational and radiality constraints. Different case studies are simulated and the impact of the I-PV system is analyzed in terms of voltage profile and voltage stability. The proposed optimal I-PV configuration resulted in loss reduction of 77.87% and 98.33% in IEEE 33- and 69-bus systems, respectively. Further, the reduced average voltage deviation index and increased voltage stability index result in an improved voltage profile and enhanced voltage stability margin in radial distribution systems and its suitability for practical applications.

The Impact of Synchronous Distributed Generation (DG) on Distribution System

2015 ◽  
Vol 785 ◽  
pp. 388-392 ◽  
Author(s):  
Hasmaini Mohamad ◽  
Shahrani Shahbudin ◽  
Nofri Yenita Dahlan
Keyword(s):  
Distributed Generation ◽  
Distribution System ◽  
System Performance ◽  
Power Flow ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Voltage Profile ◽  
Before And After ◽  
Potential Benefits ◽  
The Impact

Interconnection of Distributed Generation (DG) in distribution system presents many potential benefits as well as drawbacks. The impacts of DG might vary with the types of generator. This paper presents a study on the impacts of synchronous DG's interconnection in distribution system. Steady state analysis is carried out to analyze the impact of DG on voltage profile and short circuit current considering before and after DG interconnection. Dynamic analysis is also performed for investigating the performance of DG when a part of distribution system is being islanded. Results show that the penetration of DG contributes to the changes of power flow in the system, hence give impacts to the overall system performance.

scholarly journals Impact of Harmonics on Power Quality and Losses in Power Distribution Systems

2015 ◽  
Vol 5 (1) ◽  
pp. 166 ◽  
Author(s):  
M. Jawad Ghorbani ◽  
Hossein Mokhtari
Keyword(s):  
Power Quality ◽  
Power Distribution ◽  
Distribution Systems ◽  
Harmonic Distortion ◽  
Equivalent Model ◽  
Power Distribution Systems ◽  
Nonlinear Loads ◽  
Distribution Feeder ◽  
The Impact

This paper investigates the harmonic distortion and losses in power distribution systems due to the dramatic increase of nonlinear loads. This paper tries to determine the amount of the harmonics generated by nonlinear loads in residential, commercial and office loads in distribution feeders and estimates the energy losses due to these harmonics. Norton equivalent modeling technique has been used to model the nonlinear loads. The presented harmonic Norton equivalent models of the end user appliances are accurately obtained based on the experimental data taken from the laboratory measurements. A 20 kV/400V distribution feeder is simulated to analyze the impact of nonlinear loads on feeder harmonic distortion level and losses. The model follows a “bottom-up” approach, starting from end users appliances Norton equivalent model and then modeling residential, commercial and office loads. Two new indices are introduced by the authors to quantize the effect of each nonlinear appliance on the power quality of a distribution feeder and loads are ranked based on these new defined indices. The simulation results show that harmonic distortion in distribution systems can increase power losses up to 20%.

scholarly journals Reliability worth Assessment of Active Distribution System Considering Protective Devices and Multiple Distributed Generation Units

2018 ◽  
Vol 7 (2) ◽  
pp. 111
Author(s):  
Subramanya Sarma S ◽  
V. Madhusudhan ◽  
V. Ganesh
Keyword(s):  
Distributed Generation ◽  
Distribution System ◽  
Distribution Systems ◽  
Renewable Energy Sources ◽  
Distribution Networks ◽  
Research Area ◽  
Test System ◽  
Primary Concern ◽  
Reliability Indices ◽  
New Research

<p>Reliability worth assessment is a primary concern in planning and designing of electrical distribution systems those operate in an economic manner with minimal interruption of electric supply to customer loads. Renewable energy sources (RES) based Distributed Generation (DG) units can be forecasted to penetrate in distribution networks due to advancement in their technology. The assessment of reliability worth of DG enhanced distribution networks is a relatively new research area. This paper proposes a methodology that can be used to analyze the reliability of active distribution systems (DG enhanced distribution system) and can be applied in preliminary planning studies to compute the reliability indices and statistics. The reliability assessment in this work is carried out with analytical approach applied on a test system and simulated results validate that installation of distributed generators can improve the distribution system reliability considerably.</p>

scholarly journals The Impact of Location and Size of the Wind Technology on Power Quality in a Distribution System with Different Loads

2019 ◽  
Vol 9 (1) ◽  
pp. 1909-1914
Keyword(s):  
Power Quality ◽  
Distribution System ◽  
Quality Parameters ◽  
Loss Reduction ◽  
Voltage Profile ◽  
Current Harmonics ◽  
Voltage Unbalance ◽  
The Impact ◽  
Voltage Profile Improvement

The impact of wind technology on power quality for a distribution system is emphasized in this paper. The Power Quality of a Distribution system depends on voltage and Frequency quality. The pros of integrating the wind turbine to the system are loss reduction and voltage profile improvement but the cons of adding renewable energy to the distribution system are represented in this paper. such as voltage unbalance, flicker, power factor, and the impact of voltage and current harmonics are measured. The performed analysis results indicated the importance of the integration of DG based on Power quality Parameters.

scholarly journals Power Quality and Performance Assessment of Grid-connected Photovoltaic Distributed Generation with Compliance to Stipulated Grid Integration Requirements

2021 ◽  
Vol 6 (7) ◽  
pp. 1-10
Author(s):  
Fredrick Nkado ◽  
Franklin Nkado
Keyword(s):  
Power Quality ◽  
Distribution System ◽  
Negative Impact ◽  
Flow Analysis ◽  
High Harmonic ◽  
Harmonic Distortion ◽  
Test System ◽  
Load Flow ◽  
Harmonic Load ◽  
The Impact

Recently, the demand for electrical energy has increased more than energy production due to the growing population and industrialization. Therefore, the distributed generators integration (DGs) into the distribution system has been widely adopted. This work examines the effect of photovoltaic-based distributed generator (PV-DG) integration on power quality effect of a radial distribution system. Firstly, the capacity and optimum placement of the PV-DG units in the distribution network are determined by employing the particle swarm optimization (PSO) algorithm. Then, the impact of PV-DG integration on voltage harmonic distortion is analyzed by performing harmonic load flow analysis. Also, the P-V curve method is used to evaluate the effects of higher PV-DG penetration levels on loading margin and voltage magnitude. The simulation results show that as the PV-DG units’ penetration level increases, a greater level of harmonic distortion is injected, implying that the PV-DG units should only be integrated up to the network’s maximum capacity. Therefore, high harmonic distortion is produced when the PV-DG units are penetrated beyond this maximum penetration level, which has a negative impact on the system’s performance. The total voltage harmonic distortion is 4.17 % and 4.24 % at PCC1 and PCC2 at the highest penetration level, allowing the acceptable harmonic distortion limit. Also, grid-connected PV-DG units improve loading margin and voltage magnitude, according to the P-V curve results. The standard IEEE-33 bus distribution system is modelled in ETAP software and is used as a test system for this study.

scholarly journals Recloser-Fuse settings in distribution systems with optimizing multiple distributed generation considering technical aspects

2020 ◽  
Vol 17 (3) ◽  
pp. 1135
Author(s):  
Ahmed Mohamed Abdelbaset ◽  
AboulFotouh A. Mohamed ◽  
Essam Abou El-Zahab ◽  
M. A. Moustafa Hassan
Keyword(s):  
Distributed Generation ◽  
Distribution System ◽  
Power Loss ◽  
Distribution Systems ◽  
Test System ◽  
Optimal Size ◽  
Loss Reduction ◽  
Voltage Profile ◽  
Power Loss Reduction ◽  
System Power

<p><span>With the widespread of using distributed generation, the connection of DGs in the distribution system causes miscoordination between protective devices. This paper introduces the problems associated with recloser fuse miscoordination (RFM) in the presence of single and multiple DG in a radial distribution system. Two Multi objective optimization problems are presented. The first is based on technical impacts to determine the optimal size and location of DG considering system power loss reduction and enhancement the voltage profile with a certain constraints and the second is used for minimizing the operating time of all fuses and recloser with obtaining the optimum settings of fuse recloser coordination characteristics. Whale Optimizer algorithm (WOA) emulated RFM as an optimization problem. The performance of the proposed methodology is applied to the standard IEEE 33 node test system. The results show the robustness of the proposed algorithm for solving the RFM problem with achieving system power loss reduction and voltage profile enhancement.</span></p>

Meta-Heuristic BPSO Based Voltage Profile Enhancement in Radial Distribution System Through Network Reconfiguration

2019 ◽  
Vol 20 (6) ◽  
Author(s):  
Mounika Kannan ◽  
Kirithikaa Sampath ◽  
Srividhya Pattabiraman ◽  
K Narayanan ◽  
Tomonobu Senjyu
Keyword(s):  
Radial Distribution ◽  
Distribution System ◽  
Power Loss ◽  
Distribution Systems ◽  
Heuristic Method ◽  
Binary Particle Swarm Optimization ◽  
Voltage Profile ◽  
Voltage Deviation ◽  
Node Voltage ◽  
The Impact

Abstract Abnormal Voltages in electrical distribution system is a threat to power system security and may cause equipment damages. Reconfiguration aids in the proper distribution of load and thus improving the voltage profile. The multi objective framework including node voltage deviation as primary objective and power loss and reliability as secondary objectives is formulated. The novel meta heuristic method based on binary particle swarm optimization (BPSO) is employed to find the optimal radial distribution network configuration for an assortment of objective function. The effect of inertia weight, position and population of swarm is deeply investigated. The proposed method has been verified on IEEE 33 and 69 bus radial distribution systems and found to be effective in minimizing node voltage deviation. The impact of the reconfigured system on voltage deviation, power loss and reliability has been studied extensively. BPSO calculations are found to be simple and has good Convergence characteristics in comparison with other meta heuristic techniques.

Sign in / Sign up

Export Citation Format

Share Document