scholarly journals Nanoindentation-Based Micro-Mechanical and Electrochemical Properties of Quench-Hardened, Tempered Low-Carbon Steel

Crystals ◽  
2020 ◽  
Vol 10 (6) ◽  
pp. 508 ◽  
Author(s):  
Muhammad ArslanHafeez ◽  
Muhammad Usman ◽  
Muhammad Adnan Arshad ◽  
Malik AdeelUmer
Keyword(s):  
Corrosion Resistance ◽  
Carbon Steel ◽  
Electrochemical Properties ◽  
Lath Martensite ◽  
Low Carbon Steel ◽  
Martensite Phase ◽  
Indentation Hardness ◽  
Low Carbon ◽  
Hno3 Solution ◽  
Quench Hardening

The nanoindentation technique is widely used to measure the micro-scale mechanical properties of various materials. Herein, the nanoindentation-based micro-mechanical and electrochemical properties of low-carbon steel were investigated after quench hardening and tempering processes. The steel was produced on a laboratory scale and subjected to quench hardening separately in two different media-water and brine (10 wt% NaCl)-and subsequent moderate temperature tempering. Microstructure analysis revealed that the lath martensite phase formed after all heat treatments, having different carbon percentages ranging from 0.26% to 0.58%. A ferrite phase was also observed in the microstructure in three different morphologies, i.e., allotriomorphic ferrite, idiomorphic ferrite, and Widmanstätten ferrite. Nanoindentation analysis showed that the brine quench hardening process provided a maximum twofold improvement in indentation hardness and a 51% improvement in stiffness with a 30% reduction in reduced elastic modulus compared with as-received steel. Electrochemical performance was also evaluated in a 1% HNO3 solution. The water quench-hardened and tempered sample exhibited the highest corrosion resistance, whereas the brine quench-hardened sample exhibited the lowest corrosion resistance among all heat-treated samples.

B&W IRON

Alloy Digest ◽  
1968 ◽  
Vol 17 (8) ◽  
Keyword(s):  
Corrosion Resistance ◽  
Carbon Steel ◽  
Physical Properties ◽  
Magnetic Permeability ◽  
Electric Motor ◽  
Low Carbon Steel ◽  
Heat Treating ◽  
Magnetic Characteristics ◽  
Low Carbon ◽  
High Magnetic Permeability

Abstract B and W IRON is a thoroughly killed, low carbon steel having a combination of ductility, toughness and high magnetic permeability. It is recommended for applications where good magnetic characteristics are of primary significance, such as in the manufacture of electric motor and generator housings. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on corrosion resistance as well as forming, heat treating, machining, and joining. Filing Code: Fe-35. Producer or source: Babcock & Wilcox Company.

SAE 1020

Alloy Digest ◽  
1987 ◽  
Vol 36 (2) ◽  
Keyword(s):  
Fracture Toughness ◽  
Corrosion Resistance ◽  
Carbon Steel ◽  
Low Carbon Steel ◽  
Heat Treating ◽  
Low Carbon ◽  
Steel Mills ◽  
Temperature Performance ◽  
Wide Range ◽  
Cold Worked

Abstract SAE 1020 is a low-carbon steel combining good machinability, workability and weldability. It is carburized for use in case-hardened components and it is used for a wide range of applications in the hot-worked, cold-worked, normalized or quenched-and-tempered conditions. Its many uses include bolts, rods, plate applications, machinery components, case-hardened parts, spinning tools and trimming dies. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fracture toughness. It also includes information on low temperature performance and corrosion resistance as well as heat treating, machining, joining, and surface treatment. Filing Code: CS-113. Producer or source: Carbon steel mills.

WEIRKOTE PLUS

Alloy Digest ◽  
1987 ◽  
Vol 36 (6) ◽  
Keyword(s):  
Corrosion Resistance ◽  
Aluminum Alloy ◽  
Carbon Steel ◽  
Physical Properties ◽  
Deep Drawing ◽  
Sheet Steel ◽  
Low Carbon Steel ◽  
Low Carbon ◽  
Steel Corp ◽  
Coated Sheet

Abstract WEIRKOTE PLUS is a Galfan-coated sheet steel. The sheet is conventional low-carbon steel normally used for galvanized sheets and strip. This digest will concentrate on the characteristics and properties of the Galfan coating which is nominally a 95% zinc-5% aluminum alloy. The coating on Weirkote Plus is ideal for a variety of tough applications. It is excellent for products that require deep drawing and it combines extra corrosion resistance with superior formability. This datasheet provides information on composition and physical properties. It also includes information on corrosion resistance as well as forming, joining, and surface treatment. Filing Code: Zn-41. Producer or source: Weirton Steel Corp.

One-step plasma deposited thin SiO x C y films for corrosion resistance of low carbon steel

2020 ◽  
pp. 1-19
Author(s):  
Alaa Fahmy ◽  
Mansour El Sabbagh ◽  
Mahmoud Bedair ◽  
Amr Gangan ◽  
Mohsen El-Sabbah ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Carbon Steel ◽  
Low Carbon Steel ◽  
Low Carbon ◽  
One Step

scholarly journals Effects of H2SO4 and HCL Concentration on the Corrosion Resistance of Protected Low Carbon Steel

2012 ◽  
Vol 20 (6) ◽  
pp. 70-76 ◽  
Author(s):  
Dr.Sami Abualnoun Ajeel ◽  
Haitham Mohammed Waadulah ◽  
Dehia AbdAlkader Sultan
Keyword(s):  
Corrosion Resistance ◽  
Carbon Steel ◽  
Low Carbon Steel ◽  
Low Carbon ◽  
Hcl Concentration

Effect of Nanoparticle Addition in Hybrid Sol-Gel Silane Coating on Corrosion Resistance of Low Carbon Steel

2013 ◽  
Vol 686 ◽  
pp. 244-249 ◽  
Author(s):  
Poovarasi Balan ◽  
Aaron Ng ◽  
Chee Beng Siang ◽  
R.K. Singh Raman ◽  
Eng Seng Chan
Keyword(s):  
Corrosion Resistance ◽  
Carbon Steel ◽  
Electrochemical Impedance ◽  
Sol Gel ◽  
Low Carbon Steel ◽  
Electrochemical Corrosion ◽  
Alumina Nanoparticles ◽  
Low Carbon ◽  
Silane Coating ◽  
Sol Gel Films

Chromium pre-treatments of metal have been replaced by silane pre-treatments as more environmental friendly option. Nanoparticles can be added in the silane sol-gel network have been reported to improve corrosion resistance. In this work, the electrochemical corrosion resistance of low carbon steel coated with hybrid organic-inorganic sol-gel film filled with nanoparticles was evaluated. The sol-gel films have been synthesized from 3-glycidoxy-propyl-trimethoxy-silane (3-GPTMS) and tetra-ethyl-ortho-silicate (TEOS) precursors. These films have been impregnated with 300 ppm of silica or alumina nanoparticles. The electrochemical behavior of the coated steel was evaluated by means of electrochemical impedance spectroscopy (EIS) and scanning electron microscopy (SEM). Equivalent circuit modeling, used for quantifying the EIS measurements showed that sol-gel films containing silica nanoparticles improved the barrier properties of the silane coating. The silica nanoparticle-containing films showed highest initial pore resistance over the five days of immersion in 0.05M NaCl.

Effect of Sol-Gel Film on the Corrosion Resistance of Low Carbon Steel Plate

2020 ◽  
Vol 984 ◽  
pp. 43-50
Author(s):  
Hua Yuan Zhang ◽  
Can Wang ◽  
Bing Xue ◽  
Jing Luo
Keyword(s):  
Corrosion Resistance ◽  
Carbon Steel ◽  
Steel Plate ◽  
Salt Spray ◽  
Sol Gel ◽  
Low Carbon Steel ◽  
Corrosion Current ◽  
Neutral Salt ◽  
Low Carbon ◽  
Gel Film

To improve the corrosion resistance on Q235 low carbon steel, in this paper, tetraethyl orthosilicate (TEOS), N-dodecyl trimethoxysilane and γ-(2,3-epoxypropoxy) propytrimethoxysilane (KH560) were used to make organic-inorganic hybrid sol-gel film. Cross cut test adhesion method, neutral salt spray test, electrochemical test and film protective efficiency were taken to value the corrosion resistance property. The corrosion topography was studied by optical microscope. In addition, potentiodynamic polarization, electrochemical impedance spectroscopy (EIS) curves and equivalent electric circuit fitting were used to analyze the corrosion mechanism. The cross cut adhesion of sol-gel film can reach 1 class and the protection class can attain 5 class after 72 hours neutral salt spray test. According to the potentiodynamic polarization curve analysis, the corrosion potential of sol-gel film coating sample after 0.5 hours immersion was -0.46 V (vs. SCE) on the 0.1 Hz, and its corrosion current density was 4.74×10-7 A·cm-2. The corrosion potential of bare Q235 low carbon steel plate after 0.5 hours immersion was -0.78 V (vs. SCE) on the 0.1 Hz, and its corrosion current density was 4.75×10-6 A·cm-2. The impedance value on 0.1 Hz (|Z|0.1Hz) (1.27×106 Ω·cm2) of sol-gel film coating sample was more than three orders of magnitude higher than the value of the low carbon steel plate. Even dipping in 3.5 wt. % NaCl for 72 hours, the |Z|0.1Hz value of sol-gel coating sample was still one order of magnitude higher than the low carbon steel plate with 0.5 hours immersion. Sol-gel film with excellent adhesion can significantly improve the corrosion resistance of low carbon steel plate. Sol-gel film can increase the protection efficiency of low carbon steel plate by 90%.

scholarly journals Environmental Behavior of Low Carbon Steel Produced by a Wire Arc Additive Manufacturing Process

Metals ◽  
2019 ◽  
Vol 9 (8) ◽  
pp. 888 ◽  
Author(s):  
Ron ◽  
Levy ◽  
Dolev ◽  
Leon ◽  
Shirizly ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Additive Manufacturing ◽  
Carbon Steel ◽  
Stress Corrosion ◽  
Environmental Behavior ◽  
Low Carbon Steel ◽  
General Corrosion ◽  
Low Carbon ◽  
Corrosion Performance ◽  
Wire Arc Additive Manufacturing

: Current additive manufacturing (AM) processes are mainly focused on powder bed technologies, such as electron beam melting (EBM) and selective laser melting (SLM). However, the main disadvantages of such techniques are related to the high cost of metal powder, the degree of energy consumption, and the sizes of the components, that are limited by the size of the printing cell. The aim of the present study was to evaluate the environmental behavior of low carbon steel (ER70S-6) produced by a relatively inexpensive AM process using wire feed arc welding. The mechanical properties were examined by tension testing and hardness measurements, while microstructure was assessed by scanning electron microscopy and X-ray diffraction analysis. General corrosion performance was evaluated by salt spray testing, immersion testing, potentiodynamic polarization analysis, and electrochemical impedance spectroscopy. Stress corrosion performance was characterized in terms of slow strain rate testing (SSRT). All corrosion tests were carried out in 3.5% NaCl solution at room temperature. The results indicated that the general corrosion resistance of wire arc additive manufacturing (WAAM) samples were quite similar to those of the counterpart ST-37 steel and the stress corrosion resistance of both alloys was adequate. Altogether, it was clearly evident that the WAAM process did not encounter any deterioration in corrosion performance compared to its conventional wrought alloy counterpart.

scholarly journals Characterization of Microstructure in High-Hardness Surface Layer of Low-Carbon Steel

Metals ◽  
2020 ◽  
Vol 10 (8) ◽  
pp. 995
Author(s):  
Haitao Xiao ◽  
Shaobo Zheng ◽  
Yan Xin ◽  
Jiali Xu ◽  
Ke Han ◽  
...  
Keyword(s):  
Surface Layer ◽  
Carbon Steel ◽  
Yield Strength ◽  
Carbon Content ◽  
Acicular Ferrite ◽  
Lath Martensite ◽  
Low Carbon Steel ◽  
Low Carbon ◽  
Upper Bainite ◽  
Mixed Microstructure

Surface hardening improves the strength of low-carbon steel without interfering with the toughness of its core. In this study, we focused on the microstructure in the surface layer (0–200 μm) of our low-carbon steel, where we discovered an unexpectedly high level of hardness. We confirmed the presence of not only upper bainite and acicular ferrite but also lath martensite in the hard surface layer. In area of 0–50 μm, a mixed microstructure of lath martensite and B1 upper bainite was formed as a result of high cooling rate (about 50–100 K/s). In area of 50–200 μm, a mixed microstructure of acicular ferrite and B2 upper bainite was formed. The average nanohardness of the martensite was as high as 9.87 ± 0.51 GPa, which was equivalent to the level reported for steel with twenty times the carbon content. The ultrafine laths with an average width of 128 nm was considered to be a key cause of high nanohardness. The average nanohardness of the ferrites was much lower than for martensite: 4.18 ± 0.39 GPa for upper bainite and 2.93 ± 0.30 GPa for acicular ferrite. Yield strength, likewise, was much higher for martensite (2378 ± 123 MPa) than for upper bainite (1007 ± 94 MPa) or acicular ferrite (706 ± 72 MPa). The high yield strength value of martensite gave the surface layer an exceptional resistance to abrasion to a degree that would be unachievable without additional heat treatment in other steels with similar carbon content.

Sign in / Sign up

Export Citation Format

Share Document