scholarly journals Numerical Study on the Dynamic Behavior of a Francis Turbine Runner Model with a Crack

Energies ◽  
2018 ◽  
Vol 11 (7) ◽  
pp. 1630 ◽  
Author(s):  
Ming Zhang ◽  
David Valentin ◽  
Carme Valero ◽  
Mònica Egusquiza ◽  
Weiqiang Zhao
Keyword(s):  
Dynamic Behavior ◽  
Numerical Study ◽  
Francis Turbine ◽  
Turbine Runner

scholarly journals Numerical Study on the Dynamic Behavior of a Francis Turbine Runner Model with a Crack

2018 ◽  
Author(s):  
Ming Zhang ◽  
Xingfang Zhang ◽  
Weiqiang Zhao
Keyword(s):  
Dynamic Behavior ◽  
Numerical Study ◽  
Forced Response ◽  
Francis Turbine ◽  
Vibration Localization ◽  
Localization Theory ◽  
Turbine Runner ◽  
Intersection Line ◽  
Monitoring Technologies ◽  
Current Monitoring

The crack in the blade is the most common type of fatigue damage for Francis turbines. However, the crack sometimes is difficult to be detected in time using the current monitoring system even when the crack is very large. To better monitor the crack, it is imperative to research the effect of a crack on the dynamic behavior of a Francis turbine. In this paper, the dynamic behavior of a Francis turbine runner model with a crack was researched numerically. The intact numerical model was first validated by the experimental data available. Then, a crack was created at the intersection line between one blade and the crown. The change in dynamic behavior with increasing crack length was investigated. Crack-induced vibration localization theory was used to explain the dynamic behavior changes due to the crack. Modal analysis showed that the adopted theory could basically explain the modal behavior change due to the crack. The FFT results of the modal shapes and the localization factors (LF) were used to explain the forced response changes due to the crack. Based on the above analysis, the challenge of crack monitoring was analyzed. This research can also provide some references for more advanced monitoring technologies.

scholarly journals Numerical study on unidirectional fluid–solid coupling of Francis turbine runner

2015 ◽  
Vol 7 (3) ◽  
pp. 168781401556893 ◽  
Author(s):  
Kan Kan ◽  
Yuan Zheng ◽  
Xin Zhang ◽  
Chunxia Yang ◽  
Yuquan Zhang
Keyword(s):  
Numerical Study ◽  
Francis Turbine ◽  
Turbine Runner

The Strength Analysis of Francis Turbine Runner Based on the Fluid-Solid Coupling

2014 ◽  
Vol 709 ◽  
pp. 41-45
Author(s):  
Kan Kan ◽  
Yuan Zheng ◽  
Xin Zhang ◽  
Bin Sun ◽  
Hui Wen Liu
Keyword(s):  
Water Pressure ◽  
Eastern China ◽  
Static Stress ◽  
Operating Conditions ◽  
Francis Turbine ◽  
Strength Analysis ◽  
Maximum Deformation ◽  
The North ◽  
North Eastern ◽  
Turbine Runner

This paper does unidirectional fluid-solid coupling calculation on the runner strength under three designed head loading conditions of a certain Francis turbine in the north-eastern China. The water pressure on the blade in the flow fields of different operating conditions is calculated by means of CFD software CFX. With the help of ansys workbench, the water pressure is loaded to the blade as structural load to conclude the static stress distribution and deformation of the runner under different operating conditions. The results show that the maximum static stress increases with the rise of the flow and appears near the influent side of the blade connected to the runner crown; the maximum deformation increases with the rise of the flow and appears on the band. The results provides effective basis for the structural design and safe operation of the Francis turbine.

Two Phase PIV Measurements at the Runner Outlet in a Francis Turbine

2003 ◽  
Author(s):  
Monica Sanda Iliescu ◽  
Gabriel Dan Ciocan ◽  
Franc¸ois Avellan
Keyword(s):  
Francis Turbine ◽  
Cavitation Flow ◽  
Two Phase ◽  
Piv Measurements ◽  
Turbine Runner ◽  
Physical Insight ◽  
Complex Phenomena ◽  
Hydro Turbines ◽  
Operating Regimes ◽  
Averaging Techniques

Part load operation of hydro turbines with fixed pitch blades causes complex instable cavitation flow in the diffuser cone. Application of PIV systems provides the opportunity to investigate the flow velocity and turbulent fields in the case of development of cavitation vortex, the so-called turbine rope, at the outlet of a Francis turbine runner. The synchronization of the PIV flow survey with the rope precession allows to apply phase averaging techniques in order to extract both the periodic velocity components and the rope layout. The influence of the turbine setting level on the volume of the cavity rope and its center is investigated, providing a physical insight on the hydrodynamic complex phenomena involved in the development of the cavitation rope at Francis turbine operating regimes.

Fluid Force Moment on the Backshroud of a Francis Turbine Runner in Precession Motion

2010 ◽  
Vol 132 (5) ◽  
Author(s):  
Bingwei Song ◽  
Hironori Horiguchi ◽  
Yumeto Nishiyama ◽  
Shinichiro Hata ◽  
Zhenyue Ma ◽  
...  
Keyword(s):  
Flow Model ◽  
Swirl Flow ◽  
Francis Turbine ◽  
Leakage Flow ◽  
Fluid Force ◽  
Disk Rotation ◽  
Leakage Flow Rate ◽  
Turbine Runner ◽  
Force Moment ◽  
Axial Clearance

The fundamental characteristics of rotordynamic fluid force moment on the backshroud of a Francis turbine runner in precession motion were studied using model tests and computations based on a bulk flow model. The runner is modeled by a disk positioned close to a casing with a small axial clearance. An inward leakage flow is produced by an external pump in the model test. The effects of the leakage flow rate, the preswirl velocity at the inlet of the clearance, and the axial clearance on the fluid force moment were examined. It was found that the fluid force moment encourages the precession motion at small forward precession angular velocity ratios and the region encouraging the precession motion is affected by the preswirl velocity. Through the comparisons of the fluid force moment with and without the rotation of the disk, it was found that the normal moment without the disk rotation did not have the effect to encourage the precession motion. Thus, the swirl flow due to disk rotation was found to be responsible for the encouragement of the precession motion.

Sign in / Sign up

Export Citation Format

Share Document