scholarly journals Feasibility Study of Co-Firing of Torrefied Empty Fruit Bunch and Coal through Boiler Simulation

Energies ◽  
2020 ◽  
Vol 13 (12) ◽  
pp. 3051
Author(s):  
Yu Jiang ◽  
Kyeong-Hoon Park ◽  
Chung-Hwan Jeon
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Power Plants ◽  
Combustion Efficiency ◽  
Combustion Characteristics ◽  
Unburned Carbon ◽  
Empty Fruit Bunch ◽  
Oxides Of Nitrogen ◽  
Heat Transfer Characteristics ◽  
Transfer Characteristics

Torrefied empty fruit bunch (EFB) co-firing is a promising technology to reduce emissions from coal-fired power plants. However, co-firing can influence the combustion and heat transfer characteristics in a coal boiler. In order to study the feasibility of co-firing application of torrefied EFB (T-EFB) in boilers, the combustion characteristics, gas emissions and heat flux distribution were analyzed, respectively. First, the kinetic parameters of T-EFB devolatilization and char oxidation were obtained by experimental analysis. Second, the computational fluid dynamics (CFD) analysis was applied to the actual 500 MWe boiler simulation to further evaluate the differences in the co-firing performance parameters (combustion characteristics and emissions) of the T-EFB and the heat transfer characteristics within the boiler. Numerical results show that T-EFB co-firing can improve the ignition characteristics of pulverized coal, reduce the formation of unburned particles. When the blending ratio was increased from 10% to 50%, significantly NOx (oxides of nitrogen) reduction (levels from 170 to 98 ppm at 6% O2) was achieved. At a blending ratio above 40%, boiler combustion efficiency decreases as the total heat flux of the boiler decreases due to an increase in the amount of unburned carbon. In addition, T-EFB co-firing can affect the heat transfer characteristics of the boiler.

Heat Transfer Characteristics of Downward Facing Hot Horizontal Surfaces Using Mist Jet Impingement

2017 ◽  
Author(s):  
Ashutosh Kumar Yadav ◽  
Parantak Sharma ◽  
Avadhesh Kumar Sharma ◽  
Mayank Modak ◽  
Vishal Nirgude ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Surface Heat Flux ◽  
Cooling System ◽  
Water Pressure ◽  
Jet Impingement ◽  
Surface Heat ◽  
Heat Transfer Characteristics ◽  
Impingement Cooling ◽  
Transfer Characteristics

Impinging jet cooling technique has been widely used extensively in various industrial processes, namely, cooling and drying of films and papers, processing of metals and glasses, cooling of gas turbine blades and most recently cooling of various components of electronic devices. Due to high heat removal rate the jet impingement cooling of the hot surfaces is being used in nuclear industries. During the loss of coolant accidents (LOCA) in nuclear power plant, an emergency core cooling system (ECCS) cool the cluster of clad tubes using consisting of fuel rods. Controlled cooling, as an important procedure of thermal-mechanical control processing technology, is helpful to improve the microstructure and mechanical properties of steel. In industries for heat transfer efficiency and homogeneous cooling performance which usually requires a jet impingement with improved heat transfer capacity and controllability. It provides better cooling in comparison to air. Rapid quenching by water jet, sometimes, may lead to formation of cracks and poor ductility to the quenched surface. Spray and mist jet impingement offers an alternative method to uncontrolled rapid cooling, particularly in steel and electronics industries. Mist jet impingement cooling of downward facing hot surface has not been extensively studied in the literature. The present experimental study analyzes the heat transfer characteristics a 0.15mm thick hot horizontal stainless steel (SS-304) foil using Internal mixing full cone (spray angle 20 deg) mist nozzle from the bottom side. Experiments have been performed for the varied range of water pressure (0.7–4.0 bar) and air pressure (0.4–5.8 bar). The effect of water and air inlet pressures, on the surface heat flux has been examined in this study. The maximum surface heat flux is achieved at stagnation point and is not affected by the change in nozzle to plate distance, Air and Water flow rates.

High heat flux flow boiling in silicon multi-microchannels – Part I: Heat transfer characteristics of refrigerant R236fa

2008 ◽  
Vol 51 (21-22) ◽  
pp. 5400-5414 ◽  
Author(s):  
Bruno Agostini ◽  
John Richard Thome ◽  
Matteo Fabbri ◽  
Bruno Michel ◽  
Daniele Calmi ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Flow Boiling ◽  
High Heat ◽  
High Heat Flux ◽  
Heat Transfer Characteristics ◽  
Flux Flow ◽  
Transfer Characteristics

Heat Transfer Characteristics of Gaseous Flows in Micro-Channels With Negative Heat Flux

2006 ◽  
Author(s):  
Chungpyo Hong ◽  
Yutaka Asako
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Constant Heat Flux ◽  
Channel Height ◽  
Gas Temperature ◽  
Heat Transfer Characteristics ◽  
Constant Heat ◽  
Transfer Characteristics ◽  
Micro Channels ◽  
Gaseous Flows

Two-dimensional compressible momentum and energy equations are solved to obtain the heat transfer characteristics of gaseous flows in micro-channels with CHF (constant heat flux) whose value is negative. The combined effect of viscous dissipation and compressibility is also investigated. The numerical methodology is based on the Arbitrary-Lagrangian-Eulerian (ALE) method. The computations are performed for channels with constant heat flux with range from −104 to −102 Wm−2. The channel height ranges from 10 to 100 μm and the aspect ratio of the channel height and length is 200. The stagnation pressure varies from 120 to 500 kPa. The outlet pressure is fixed at the atmosphere. The wall and bulk temperatures in micro-channels are compared with those of the case of positive heat flux and also compared with those of the incompressible flow in a conventional sized channel. In the case of negative heat flux, temperature profiles normalized by heat flux have different trends in the case of positive heat flux, when flow is fast. A gas temperature falls down due to the energy conversion. A correlation for the prediction of the wall temperature of the gaseous flow in the micro-channel is proposed.

Heat Transfer Characteristics of a Radial Jet Reattachment Flame

1997 ◽  
Vol 119 (2) ◽  
pp. 258-264 ◽  
Author(s):  
J. W. Mohr ◽  
J. Seyed-Yagoobi ◽  
R. H. Page
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Combustion Process ◽  
Local Heat ◽  
Operating Conditions ◽  
Recirculation Region ◽  
Heat Transfer Characteristics ◽  
Transfer Characteristics ◽  
Impingement Surface

A Radial Jet Reattachment Combustion (RJRC) nozzle forces primary combustion air to exit radially from the combustion nozzle and to mix with gaseous fuel in a highly turbulent recirculation region generated between the combustion nozzle and impingement surface. High convective heat transfer properties and improved fuel/ air mixing characterize this external mixing combustor for use in impingement flame heating processes. To understand the heat transfer characteristics of this new innovative practical RJRC nozzle, statistical design and analysis of experiments was utilized. A regression model was developed which allowed for determination of the total heat transfer to the impingement surface as well as the NOx emission index over a wide variety of operating conditions. In addition, spatially resolved flame temperatures and impingement surface temperature and heat flux profiles enabled determination of the extent of the combustion process with regards to the impingement surface. Specifically, the relative sizes of the reaction envelope, high temperature reaction zone, and low temperature recirculation zone were all determined. At the impingement surface in the reattachment zone very high local heat flux values were measured. This study provides the first detailed local heat transfer characteristics for the RJRC nozzle.

Sign in / Sign up

Export Citation Format

Share Document