scholarly journals Effects of Cold-Rolling/Aging Treatments on the Shape Memory Properties of Ti49.3Ni50.7 Shape Memory Alloy

Materials ◽  
2017 ◽  
Vol 10 (7) ◽  
pp. 704 ◽  
Author(s):  
Shih-Hang Chang ◽  
Keng-Hua Lin ◽  
Shyi-Kaan Wu
Keyword(s):  
Shape Memory Alloy ◽  
Cold Rolling ◽  
Shape Memory ◽  
Shape Memory Properties

Effect of Electroplastic Deformation on Martensitic Transformation in Coarse Grained and Ultrafine Grained Ni-Ti Shape Memory Alloy

2008 ◽  
Vol 584-586 ◽  
pp. 127-132 ◽  
Author(s):  
Anastasia E. Sergeeva ◽  
Daria Setman ◽  
Michael Zehetbauer ◽  
Sergey Prokoshkin ◽  
Vladimir V. Stolyarov
Keyword(s):  
Differential Scanning Calorimetry ◽  
Martensitic Transformation ◽  
Shape Memory Alloy ◽  
Cold Rolling ◽  
Shape Memory ◽  
Coarse Grained ◽  
Scanning Calorimetry ◽  
Structure Relaxation ◽  
Differential Scanning Calorimetry Method ◽  
Ultrafine Grained

The aim of this paper is the investigation of electroplastic deformation (EPD) and subsequent annealing influence on martensitic transformation in the shape memory Ni50.7Ti49.3 alloy. Using differential scanning calorimetry method it was shown that EPD at the low strain stimulates structure relaxation and recovers martensitic transformation in cooling, which is usually suppressed by cold rolling.

Effect of the Addition of Gd on Ni53Mn22Co6Ga19 High-Temperature Shape Memory Alloy

2010 ◽  
Vol 654-656 ◽  
pp. 2095-2098
Author(s):  
Yun Qing Ma ◽  
Shui Yuan Yang ◽  
San Li Lai ◽  
Shi Wen Tian ◽  
Cui Ping Wang ◽  
...  
Keyword(s):  
Grain Size ◽  
High Temperature ◽  
Martensitic Transformation ◽  
Shape Memory Alloy ◽  
Shape Memory ◽  
Earth Element ◽  
Stress And Strain ◽  
Martensitic Transformation Temperature ◽  
Rich Phase ◽  
Shape Memory Properties

The rare earth element Gd is added to Ni53Mn22Co6Ga19 high-temperature shape memory alloy to refine the grain size and adjust the distribution of γ phase, and their microstructure, martensitic transformation behaviors, mechanical and shape memory properties were investigated. The results show that the grain size is obviously decreased and the γ phase tends to segregate at grain boundaries with increasing Gd content. Small amounts of Gd-rich phase were formed with 0.1 at.% Gd addition. The martensitic transformation temperature abruptly increases with 0.1 at.% Gd addition, then almost keeps constant with further increasing Gd content. The addition of 0.1 at.% Gd is proved to be beneficial to both tensile stress and strain before fracture, but negative to the shape-memory effect.

Transformation behaviors and superelasticity of Ti50Ni48Fe2 shape memory alloy subjected to cold-rolling and subsequent annealing

Rare Metals ◽  
2014 ◽  
Vol 33 (6) ◽  
pp. 652-656 ◽  
Author(s):  
Xiao-Bo Yuan ◽  
Bin Chen ◽  
Fu-Shun Liu ◽  
Qing Xu ◽  
Wen Ma
Keyword(s):  
Shape Memory Alloy ◽  
Cold Rolling ◽  
Shape Memory ◽  
Subsequent Annealing

scholarly journals Microstructural characterization of Cu82.3Al8.3Mn9.4 shape memory alloy after rolling

10.30544/314 ◽  
2017 ◽  
Vol 23 (3) ◽  
pp. 281-289
Author(s):  
Mirko Gojić ◽  
Stjepan Kožuh ◽  
Ivana Ivanić ◽  
Magdalena Selanec ◽  
Tamara Holjevac Grgurić ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Shape Memory Alloy ◽  
Cold Rolling ◽  
Shape Memory ◽  
Microstructural Characterization ◽  
Rolling Process ◽  
Scanning Calorimetry ◽  
Two Phase ◽  
Hot And Cold Rolling

In this paper, the microstructure of Cu82.3Al8.3Mn9.4 (in wt. %) shape memory alloy after hot and cold rolling was investigated. The Cu82.3Al8.3Mn9.4 alloy was produced by a vertical continuous casting method in the form a cylinder rod of 8 mm in diameter. After the casting, hot and cold rolling was performed. By hot rolling a strip with a thickness of 1.75 mm was obtained, while by cold rolling a strip with a thickness of 1.02 mm was produced. After the rolling process, heat treatment was performed. Heat treatment was carried out by solution annealing at 900 °C held for 30 minutes and water quenched immediately after heating. The microstructure characterization of the investigated alloy was carried out by optical microscopy (OM), scanning electron microscopy (SEM) equipped with a device for energy dispersive spectroscopy (EDS). Phase transformation temperatures and fusion enthalpies were determined by differential scanning calorimetry (DSC) method. The homogenous martensite microstructure was confirmed by OM and SEM micrographs after casting. During rolling the two-phase microstructure occurred. Results of DSC analysis showed martensite start (Ms), martensite finish (Mf), austenite start (As) and austenite finish (Af) temperatures.

Effect of Tin Addition on Shape Memory Effect and Mechanical Properties of Cu-Al-Ni Shape Memory Alloy

2020 ◽  
Vol 38 (8A) ◽  
pp. 1178-1186
Author(s):  
Raad S. Ahmed Adnan
Keyword(s):  
Mechanical Properties ◽  
Shape Memory Alloy ◽  
Shape Memory ◽  
Shape Memory Effect ◽  
Transformation Temperature ◽  
Mechanical Test ◽  
Hardness Test ◽  
Micro Hardness ◽  
Recovery Strain ◽  
Shape Memory Properties

This study examines the effect of Sn additions on Cu-14%Al-4.5%Ni shape memory alloy. Sn was added in three different percentages (0.3,1,3) %. The alloys were mechanically tested both in compression test and micro hardness test. Also, a thermo-mechanical test was performed on the alloys. Results showed an increase in the transformation temperature outside the domain and also a better recovery strain with the increase of Sn percentage of 3% Sn addition showed the best results in mechanical properties while the 3% Sn showed a better Shape Memory Properties near to super elastic.

Sign in / Sign up

Export Citation Format

Share Document