scholarly journals Hot Deformation Behavior Considering Strain Effects and Recrystallization Mechanism of an Al-Zn-Mg-Cu Alloy

Materials ◽  
2020 ◽  
Vol 13 (7) ◽  
pp. 1743 ◽  
Author(s):  
Lei Luo ◽  
Zhiyi Liu ◽  
Song Bai ◽  
Juangang Zhao ◽  
Diping Zeng ◽  
...  
Keyword(s):  
Dynamic Recrystallization ◽  
Hot Deformation ◽  
Deformation Behavior ◽  
Processing Parameters ◽  
Strain Rate Range ◽  
Hot Compression ◽  
Processing Maps ◽  
Hot Deformation Behavior ◽  
Recrystallization Mechanism ◽  
Cu Alloy

The hot deformation behavior of an Al-Zn-Mg-Cu alloy was investigated by hot compression test at deformation temperatures varying from 320 to 440 °C with strain rates ranging from 0.01 to 10 s−1. The results show that the Mg(Zn, Cu)2 particles as a result of the sufficient static precipitation prior to hot compression have an influence on flow softening. A constitutive model compensated with strain was developed from the experimental results, and it proved to be accurate for predicting the hot deformation behavior. Processing maps at various strains were established. The microstructural evolution demonstrates that the dominant dynamic softening mechanism stems from dynamic recovery (DRV) and partial dynamic recrystallization (DRX). The recrystallization mechanism is continuous dynamic recrystallization (CDRX). The microstructure observations are in good agreement with the results of processing maps. On account of the processing map and microstructural observation, the optimal hot processing parameters at a strain of 0.6 are at deformation temperature range of 390–440 °C and strain rate range of 0.010–0.316 s−1 with a peak efficiency of 0.390.

scholarly journals Effect of Nitrogen Content on Hot Deformation Behavior and Grain Growth in Nuclear Grade 316LN Stainless Steel

2015 ◽  
Vol 2015 ◽  
pp. 1-8 ◽  
Author(s):  
Ming-wei Guo ◽  
Zhen-hua Wang ◽  
Ze-an Zhou ◽  
Shu-hua Sun ◽  
Wan-tang Fu
Keyword(s):  
Stainless Steel ◽  
Dynamic Recrystallization ◽  
Strain Rate ◽  
Grain Growth ◽  
Strain Rate Sensitivity ◽  
Hot Deformation ◽  
Deformation Behavior ◽  
Rate Sensitivity ◽  
Processing Maps ◽  
Hot Deformation Behavior

316LN stainless steel with 0.08%N (08N) and 0.17%N (17N) was compressed at 1073–1473 K and 0.001–10 s−1. The hot deformation behavior was investigated using stress-strain curve analysis, processing maps, and so forth. The microstructure was analyzed through electron backscatter diffraction analysis. Under most conditions, the deformation resistance of 17N was higher than that of 08N. This difference became more pronounced at lower temperatures. The strain rate sensitivity increased with increasing temperature for types of steel. In addition, the higher the N content, the higher the strain rate sensitivity. Hot deformation activation energy increased from 487 kJ/mol to 549 kJ/mol as N concentration was increased from 0.08% to 0.17%. The critical strain for initiation of dynamic recrystallization was lowered with increasing N content. In the processing maps, both power dissipation ratio and unstable region increased with increasing N concentration. In terms of microstructure evolution, N promoted dynamic recrystallization kinetic and decreased dynamic recrystallization grain size. The grain growth rate was lower in 17N than in 08N during heat treatment. Finally, it was found that N favored twin boundary formation.

scholarly journals Hot Deformation Behavior and Processing Maps of Fe-30Mn-0.11C Steel

Materials ◽  
2018 ◽  
Vol 11 (10) ◽  
pp. 1940 ◽  
Author(s):  
Jianmei Kang ◽  
Yuhui Wang ◽  
Zhimeng Wang ◽  
Yiming Zhao ◽  
Yan Peng ◽  
...  
Keyword(s):  
Dynamic Recrystallization ◽  
Hot Deformation ◽  
Deformation Behavior ◽  
True Strain ◽  
Peak Stress ◽  
Strain Rates ◽  
Processing Maps ◽  
Compression Tests ◽  
Hot Deformation Behavior ◽  
High Deformation

Hot deformation behavior of Fe-30Mn-0.11C steel was investigated. Hot compression tests were carried out at various temperatures ranging from 800 °C to 1200 °C and at different strain rates of 0.01 s−1 to 10 s−1. The constitutive equation based on peak stress was established. Hot processing maps at different strains and recrystallization diagrams were also established and analyzed. The results show that dynamic recrystallization easily occur at high deformation temperatures and low strain rates. Safe and unstable zones are determined at the true strain of 0.6 and 0.7, and the hot deformation process parameters of partial dynamic recrystallization of the tested steel are also obtained.

Characterization of Hot Deformation Behavior of Zr-4 Alloy in Material Application Area

2012 ◽  
Vol 578 ◽  
pp. 202-205
Author(s):  
Guo Qing Lin
Keyword(s):  
Strain Rate ◽  
Hot Deformation ◽  
Deformation Behavior ◽  
Flow Behavior ◽  
Strain Rate Range ◽  
Processing Maps ◽  
Peak Efficiency ◽  
Hot Deformation Behavior ◽  
Rate Range ◽  
Temperature Range

The hot deformation behavior of Zr-4 alloy was studied in the temperature range 650-900°C and strain rate range 0.005-50s-1 using processing maps. The processing maps revealed three domains: the first occurs in the temperature range 780-820°C and strain rate range 0.005-0.05s-1, and has a peak efficiency of 45% at 790°C and 0.005s-1; the mechanism is the dynamic recrystallization. The second occurs in the temperature range greater than 900°C and strain rate range 0.05-0.8s-1, and has a peak efficiency of 40% at 900°C and 0.5s-1, which are the domains of dynamic recovery. In addition, the instability zones of flow behavior can also be recognized by the maps in the temperature range 650-780°C and strain rate range 0.01-0.1s-1, which should be strictly avoided in the processing of the material. Zr-4 alloy is the material for pressure tube applications in nuclear reactors and has better strength and a lower rate of hydrogen uptake compared to other materials under similar service conditions.

Hot Deformation Behavior and Processing Maps of 7050 Aluminum Alloy

2013 ◽  
Vol 815 ◽  
pp. 37-42 ◽  
Author(s):  
Yu Juan Guo ◽  
Lei Deng ◽  
Xin Yun Wang ◽  
Jun Song Jin ◽  
Wen Wu Zhou
Keyword(s):  
Strain Rate ◽  
Hot Deformation ◽  
Deformation Behavior ◽  
Strain Rate Range ◽  
Processing Maps ◽  
Compression Tests ◽  
Hot Deformation Behavior ◽  
Temperature Range ◽  
Optimal Processing ◽  
Working Region

The hot deformation behavior of 7050aluminum alloy was investigated by hot compression tests in the temperature range of 573-773K and the strain rate ranging from 0.001s-1to 10 s-1.The flow curves showed that the flow stresses increase with the increase of strain rate or the decrease of temperature.In order to determine the optimal processing conditions, hot processing maps were established based on experimental data and Dynamic Materials Model. The processing maps indicate that instability occur at low temperature and high strain rate. The optimum hot working region is the domain in the temperature range of 673-723K and strain rate range of 0.001-0.01 s-1,where typical recrystallization was observed in the optical microstructures.

Study on Hot Deformation Behavior and Processing Maps of Cu-0.35Cr-0.15Zr Alloy

2011 ◽  
Vol 189-193 ◽  
pp. 1456-1464
Author(s):  
Jiao Yan Dai ◽  
Si Guo Mu ◽  
Yong Ru Wang
Keyword(s):  
Hot Deformation ◽  
Deformation Behavior ◽  
Flow Behavior ◽  
Processing Parameters ◽  
Processing Maps ◽  
Compression Tests ◽  
Hot Deformation Behavior ◽  
Dynamic Materials ◽  
Hyperbolic Sine ◽  
Dynamic Materials Model

The hot deformation behavior of Cu-0.35Cr-0.15Zr (wt.%) alloy was investigated by hot compression tests using a Gleeble-1500D thermal simulator system. The tests were performed under the conditions of 700°С- 820°С temperature and 0.01-10s-1strain rate. The results show that the flow behavior of the studied alloy could be described by the hyperbolic sine constitutive equation, and an active energy of 597.53 kJ/mol was calculated. The processing maps were obtained and analyzed according to the dynamic materials model. The optimum processing parameters of hot deformation of this alloy in the range of this experiment can be attained by the maps. The hot deformation temperature was 800-820°C and the strain rate was 0.01-0.1s-1.The instability zones of flow behavior can also be recognized by the maps.

Sign in / Sign up

Export Citation Format

Share Document