scholarly journals Surface Modification Using Assisting Electrodes in Wire Electrical Discharge Machining for Silicon Wafer Preparation

Materials ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1355
Author(s):  
Chunliang Kuo ◽  
Yupang Nien ◽  
Anchun Chiang ◽  
Atsushi Hirata
Keyword(s):  
Surface Roughness ◽  
Surface Modification ◽  
Electrical Discharge ◽  
Polycrystalline Silicon ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Wire Electrical Discharge Machining ◽  
Electrode Thickness ◽  
Machined Surface ◽  
Pulse On Time

This paper outlines notable advances in the wire electrical discharge machining of polycrystalline silicon workpieces for wafer preparation. Our use of assisting electrodes permits the transfer of aluminum particles to the machined surface of the polycrystalline silicon workpieces, to enhance conductivity and alter surface topography regardless of the silicon’s crystallographic structure and diamond-type lattice. This in-process surface modification technique was shown to promote material removal and simultaneously preserve the integrity of the machined surfaces with preferable surface textures. In the validation experiment, the 25 mm-thick assisting electrodes deposited a notable concentration of aluminium on the machined surface (~3.87 wt %), which greatly accelerated the rate of material removal (~9.42 mg/s) with minimal surface roughness (Sa ~5.49 μm) and moderate skewness (−0.23). The parameter combination used to obtain the optimal surface roughness (Sa 2.54 μm) was as follows: open voltage (80 V), electrical resistance (1.7 Ω), pulse-on time (30 μs), and electrode thickness (15 mm). In multiple objective optimization, the preferred parameter combination (open voltage = 80 V, resistance = 1.4 Ω, pulse-on time = 60 μs, and assisting electrode thickness = 25 mm) achieved the following appreciable results: surface modification of 3.26 ± 0.61 wt %, material removal rate of 7.08 ± 2.2 mg/min, and surface roughness of Sa = 4.3 ± 1.67 μm.

scholarly journals Optimization of Process Parameters for Minimum Surface Roughness in Wire Electrical Discharge Machining of AISI 1045 Steel Using Taguchi Method

2021 ◽  
Vol 9 (10) ◽  
pp. 989-997
Author(s):  
Rouhan Rafiq
Keyword(s):  
Surface Roughness ◽  
Process Parameters ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Wire Electrical Discharge Machining ◽  
Input Parameters ◽  
Pulse On Time

Abstract: One of the important non-traditional machining processes is Wire Electrical Discharge Machining, used for machining difficult to machine materials like composites and inter-metallic materials. WEDM involves complex physical and chemical process including heating and cooling. Accompanying the development of mechanical industry, the demand for alloy materials having high hardness, toughness and impact resistance are increasing. The WEDM satisfy the present demands of the manufacturing industries such as better finish, low tolerance, higher production rate, miniaturization etc. The consistent quality of parts being machined in WEDM is difficult because the process parameters cannot be controlled effectively. The problem of arriving at the optimum levels of the operating parameters has attracted the attention of the researcher and practicing engineers for a very long time. The objective of the present study was to experimentally investigate the effects of various Wire Electrical Discharge Machining variables on Surface Roughness and Material Removal Rate of AISI 1045 using ANOVA method. Taguchi’s L18 Orthogonal Array was used to conduct experiments, which correspond to randomly chosen different combination of process parameters: wire type, pulse on time, pulse off time, peak current, servo voltage, wire feed rate, flushing pressure each to be varied in three different levels. The surface roughness and material removal rate were selected as output responses for the present investigation. The effect of all the input parameters on the output responses have been analyzed using analysis of variance (ANOVA). The effect of variation in input parameters has been studied on the output responses. Plots of S/N ratio have been used to determine the best relationship between the responses and the input parameters. In other words, the optimum set of input parameters for minimum surface roughness and maximum material removal rate were determined. It has been found that wire type, pulse on time are most significant factors for surface roughness and wire type, pulse on time, pulse off time, wire feed rate are most significant factors for material removal rate. Keywords: Input Parameters, Wire Electric Discharge Machining, ANOVA, Taguchi

scholarly journals The Effect of Discharge Current and Pulse-On Time on Biocompatible Zr-based BMG Sinking-EDM

2020 ◽  
Vol 10 (1) ◽  
pp. 401-407
Author(s):  
Yanuar Rohmat Aji Pradana ◽  
Aldi Ferara ◽  
Aminnudin Aminnudin ◽  
Wahono Wahono ◽  
Jason Shian-Ching Jang
Keyword(s):  
Surface Roughness ◽  
Metallic Glasses ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Surface Hardness ◽  
Recast Layer ◽  
Surface Evaporation ◽  
Pulse On Time

AbstractThe machinability information of Zr-based bulk metallic glasses (BMGs) are recently limited but essential to provide technological recommendation for the fabrication of the medical devices due to the material’s metastable nature. This study aims to investigate the material removal rate (MRR) and surface roughness under different current and pulse-on time of newly developed Ni- and Cu-free Zr-based BMG using sinking-electrical discharge machining (EDM). By using weightloss calculation, surface roughness test and scanning electron microscopy (SEM) observation on the workpiece after machining, both MRR and surface roughness were obtained to be increased up to 0.594 mm3/min and 5.50 μm, respectively, when the higher current was applied. On the other hand, the longer pulse-on time shifted the Ra into the higher value but lower the MRR value to only 0.183 mm3/min at 150 μs. Contrary, the surface hardness value was enhanced by both higher current and pulse-on time applied during machining indicating different level of structural change after high-temperature spark exposure on the BMG surface. These phenomena are strongly related to the surface evaporation which characterize the formation of crater and recast layer in various thicknesses and morphologies as well as the crystallization under the different discharge energy and exposure time.

Studies of kerf width and surface roughness using the response surface methodology in AA 4032–TiC composites

2021 ◽  
pp. 095440892110414
Author(s):  
TS Senthilkumar ◽  
R Muralikannan ◽  
T Ramkumar ◽  
S Senthil Kumar
Keyword(s):  
Surface Roughness ◽  
Response Surface Methodology ◽  
Response Surface ◽  
Metal Matrix ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Kerf Width ◽  
Wire Electrical Discharge Machining ◽  
Box Behnken Design ◽  
Pulse On Time

A substantially developed machining process, namely wire electrical discharge machining (WEDM), is used to machine complex shapes with high accuracy. This existent work investigates the optimization of the process parameters of wire electrical discharge machining, such as pulse on time ( Ton), peak current ( I), and gap voltage ( V), to analyze the output performance, such as kerf width and surface roughness, of AA 4032–TiC metal matrix composite using response surface methodology. The metal matrix composite was developed by handling the stir casting system. Response surface methodology is implemented through the Box–Behnken design to reduce experiments and design a mathematical model for the responses. The Box–Behnken design was conducted at a confident level of 99.5%, and a mathematical model was established for the responses, especially kerf width and surface roughness. Analysis of variance table was demarcated to check the cogency of the established model and determine the significant process. Surface roughness attains a maximum value at a high peak current value because high thermal energy was released, leading to poor surface finish. A validation test was directed between the predicted value and the actual value; however, the deviation is insignificant. Moreover, a confirmation test was handled for predicted and experimental values, and a minimal error was 2.3% and 2.12% for kerf width and surface roughness, respectively. Furthermore, the size of the crater, globules, microvoids, and microcracks were increased by amplifying the pulse on time.

Surface Roughness at Wire Electrical Discharge Machining

2015 ◽  
Vol 760 ◽  
pp. 551-556 ◽  
Author(s):  
Oana Dodun ◽  
Laurenţiu Slătineanu ◽  
Margareta Coteaţă ◽  
Vasile Merticaru ◽  
Gheorghe Nagîţ
Keyword(s):  
Surface Roughness ◽  
Empirical Model ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Roughness Parameter ◽  
Wire Electrical Discharge Machining ◽  
Power Type ◽  
Surface Roughness Parameter ◽  
Pulse On Time ◽  
Pulse Off Time

Wire electrical discharge machining is a machining method by which parts having various contours could be detached from plate workpieces. The method uses the electrical discharges developed between the workpiece and the wire tool electrode found in an axial motion, when in the work zone a dielectric fluid is recirculated. In order to highlight the influence exerted by some input process factors on the surface roughness parameter Ra in case of a workpiece made of an alloyed steel, a factorial experiment with six independent variables at two variation levels was designed and materialized. As input factors, one used the workpiece thickness, pulse on time, pulse off-time, wire axial tensile force, current intensity average amplitude defined by setting button position and travelling wire electrode speed. By mathematical processing of the experimental results, empirical models were established. Om the base of a power type empirical model, graphical representations aiming to highlight the influence of some input factors on the surface roughness parameter Ra were achieved. The power type empirical model facilitated establishing of order of factors able to exert influence on the surface roughness parameter Ra at wire electrical discharge machining.

Influence of Pulse-on-Time on the Performance of Wire Electrical Discharge Machining of Ti-6Al-4V Using Zinc Coated Brass Wire

2014 ◽  
Vol 592-594 ◽  
pp. 416-420 ◽  
Author(s):  
Singaravelu D. Lenin ◽  
A. Uthirapathi ◽  
Ramana Reddy P.S. Venkata ◽  
Muthukannan Durai Selvam
Keyword(s):  
Surface Roughness ◽  
Electrical Discharge ◽  
Metal Removal ◽  
Electrical Discharge Machining ◽  
Kerf Width ◽  
Dielectric Fluid ◽  
Wire Electrical Discharge Machining ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Brass Wire

The present paper describes the influence of pulse-on-time on performance features such as Metal Removal Rate (MRR), Kerf width, Surface Roughness (SR) on cutting Titanium alloy (Ti-6Al-4V) in wire electrical discharge machining (WEDM) using zinc coated brass wire. The deionised water is used as dielectric fluid. The process parameters such as wire tension, wire speed, flushing pressure, discharge current, sparking voltage and pulse off time have kept constant at appropriate values throughout the experiment and the pulse on time is varied at nine different intervals. It was found that pulse-on-time is the most significant factor which greatly influences MRR, kerf width, and SR. It was also observed that taper at the end of cutting zone which is unavoidable occurrence for the machined part. This is due to the erosion of wire material. The surface roughness increases with increase in pulse on time also with higher rate of MRR.

Surface Roughness Optimization of Wire Electrical Discharge Machining Using ABC Algorithm

2015 ◽  
Vol 766-767 ◽  
pp. 902-907
Author(s):  
Bibin K. Tharian ◽  
B. Kuriachen ◽  
Josephkunju Paul ◽  
Paul V. Elson
Keyword(s):  
Surface Roughness ◽  
Process Parameters ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Wire Electrical Discharge Machining ◽  
Wire Tension ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Off Time ◽  
Wire Feed

Wire electrical discharge machining is one of the important non-traditional machining processes for machining difficult to machine materials. It involves the removal of material by the discrete electric discharges produced between the inter electrode gap of continuously moving wire electrode and the work piece. The ability to produce intricate profiles on materials irrespective of the mechanical properties made this process to be widely used in industries. The present study investigates the relationship of various process parameters in WEDM of AISI 202 stainless steel with brass electrode.The experiments were planned according to Taguchi’s L18 orthogonal array and experimental models were developed. The important process parameters identified for the present study were pulse on time, peak current, pulse off time, wire feed, wire tension, dielectric flushing pressure, servo feed and gap voltage. The surface roughness of the machined surface was measured as the process performance measure. Analysis of variance test has also been carried out to check the adequacy of the developed models and to identify the level of significance of each process parameters. In addition to the developed models, ABC optimization has been performed to identify the optimum parameter combination for minimum surface roughness and the obtained optimal process parameters are peak current 11 A, pulse on time 100 μs, pulse off time 49 μs, wire feed 4 m/min, wire tension 10 N, flushing pressure 12 kg/cm2, servo feed 2100 mm/min and set gap voltage 30 V. Finally the results were verified with the experimental results and found that they are in good agreement.

Surface Study in a Non-conventional (Electrical Discharge Machining) Process for Grade 6 Titanium Material

2014 ◽  
Vol 68 (1) ◽  
Author(s):  
Md. Ashikur Rahman Khan ◽  
M. M. Rahman
Keyword(s):  
Surface Roughness ◽  
Process Parameters ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Machining Process ◽  
Machined Surface ◽  
Titanium Material ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Off Time

Electrical discharge machining (EDM) produces complex shapes and permits high-precision machining of any hard or difficult-to-cut materials. The performance characteristics such as surface roughness and microstructure of the machined face are influenced by numerous parameters. The selection of parameters becomes complicated. Thus, the surface roughness (Ra) and microstructure of the machined surface in EDM on Grade 6 titanium alloy are studied is this study. The experimental work is performed using copper as electrode material. The polarity of the electrode is maintained as negative. The process parameters taken into account in this study are peak current (Ip), pulse-on time (Ton), pulse-off time (Toff), and servo-voltage (Sv). A smooth surface finish is found at low pulse current, small on-time and high off-time. The servo-voltage affects the roughness diversely however, a finish surface is found at 80 V Sv. Craters, cracks and globules of debris are appeared in the microstructure of the machined part. The size and degree of craters as well as cracks increase with increasing in energy level. Low discharge energy yields an even surface. This approach helps in selecting proper process parameters resulting in economic EDM machining. 

Comparative evaluation of powder-mixed and ultrasonic-assisted rough die-sinking electrical discharge machining based on pulse characteristics

2019 ◽  
Vol 233 (14) ◽  
pp. 2515-2530 ◽  
Author(s):  
R Rajeswari ◽  
MS Shunmugam
Keyword(s):  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Graphite Powder ◽  
Machining Process ◽  
Machined Surface ◽  
Ultrasonic Assisted ◽  
Pulse On Time

Electrical discharge machining is used in the machining of complicated shapes in hardened molds and dies. In rough die-sinking stage, attempts are made to enhance material removal rate with a consequential reduction in cycle time. Powder mix and ultrasonic assistance are employed in the electrical discharge machining process to create gap conditions favoring material removal. In the present work, experiments are carried out on hardened D3 die steel using full-factorial design based on three levels of voltage, current and pulse on time. The gap phenomena in graphite powder-mixed and ultrasonic-assisted rough electrical discharge machining are studied using a detailed analysis of pulse shapes and their characteristic trains. Two new parameters, namely, energy expended over a second ( E) and performance factor ( PF) denoting the ratio of energy associated with sparks to total discharge energy, bring out gap conditions effectively. In comparison with the conventional electrical discharge machining for the selected condition, it is seen that the graphite powder mixed in the dielectric enhances the material removal rate by 20.8% with E of 215 J and PF of 0.227, while these values are 179.8 J and 0.076 for ultrasonic-assisted electrical discharge machining with marginal reduction of 3.9%. Cross-sectional images of workpieces also reveal the influence of electrical discharge machining conditions on the machined surface. The proposed approach can be extended to different powder mix and ultrasonic conditions to identify condition favoring higher material removal.

Sign in / Sign up

Export Citation Format

Share Document