scholarly journals Programmed Plastic Deformation in Mathematically-Designed Architected Cellular Materials

Metals ◽  
2021 ◽  
Vol 11 (10) ◽  
pp. 1622
Author(s):  
Oraib Al-Ketan
Keyword(s):  
Plastic Deformation ◽  
Relative Density ◽  
Deformation Behavior ◽  
Cellular Materials ◽  
Plateau Stress ◽  
Plastic Deformation Behavior ◽  
Unit Cells ◽  
Designed Materials ◽  
Deformation Patterns ◽  
Damage Tolerant

The ability to control the exhibited plastic deformation behavior of cellular materials under certain loading conditions can be harnessed to design more reliable and structurally efficient damage-tolerant materials for crashworthiness and protective equipment applications. In this work, a mathematically-based design approach is proposed to program the deformation behavior of cellular materials with minimal surface-based topologies and ductile constituent material by employing the concept of functional grading to control the local relative density of unit cells. To demonstrate the applicability of this design tactic, two examples are presented. Rhombic, and double arrow deformation profiles were programmed as the desired deformation patterns. Grayscale images were used to map the relative density distribution of the cellular material. 316L stainless steel metallic samples were fabricated using the powder bed fusion additive manufacturing technique. Results of compressive tests showed that the designed materials followed the desired programmed deformation behavior. Results of mechanical testing also showed that samples with programmed deformation exhibited higher plateau stress and toughness values as compared to their uniform counterparts while no effect on Young’s modulus was observed. Plateau stress values increased by 8.6% and 13.4% and toughness values increased by 5.6% and 11.2% for the graded-rhombic and graded-arrow patterns, respectively. Results of numerical simulations predicted the exact deformation behavior that was programmed in the samples and that were obtained experimentally.

Effect of Grain Size on Deformation Twinning Behavior of Ti6Al4V Alloy

2015 ◽  
Vol 830-831 ◽  
pp. 337-340
Author(s):  
Ashish Kumar Saxena ◽  
Manikanta Anupoju ◽  
Asim Tewari ◽  
Prita Pant
Keyword(s):  
Plastic Deformation ◽  
Grain Size ◽  
Strain Rate ◽  
Deformation Behavior ◽  
Deformation Behaviour ◽  
Air Cooling ◽  
Specific Strength ◽  
Aerospace Applications ◽  
Β Phase ◽  
Plastic Deformation Behavior

An understanding of the plastic deformation behavior of Ti6Al4V (Ti64) is of great interest because it is used in aerospace applications due to its high specific strength. In addition, Ti alloys have limited slip systems due to hexagonal crystal structure; hence twinning plays an important role in plastic deformation. The present work focuses upon the grain size effect on plastic deformation behaviour of Ti64. Various microstructures with different grain size were developed via annealing of Ti64 alloy in α-β phase regime (825°C and 850°C) for 4 hours followed by air cooling. The deformation behavior of these samples was investigated at various deformation temperature and strain rate conditions. Detailed microstructure studies showed that (i) smaller grains undergoes twinning only at low temperature and high strain rate, (ii) large grain samples undergo twinning at all temperatures & strain rates, though the extent of twinning varied.

scholarly journals Plastic Deformation Behavior of Metal for Complex Loading Paths

1975 ◽  
Vol 18 (125) ◽  
pp. 1209-1217 ◽  
Author(s):  
Kenji KANEKO ◽  
Kozo IKEGAMI ◽  
Eiryo SHIRATORI
Keyword(s):  
Plastic Deformation ◽  
Deformation Behavior ◽  
Complex Loading ◽  
Loading Paths ◽  
Plastic Deformation Behavior

Prediction of 3D Microstructure and Plastic Deformation Behavior in Dual-Phase Steel Using Multi-Phase Field and Crystal Plasticity FFT Methods

2015 ◽  
Vol 651-653 ◽  
pp. 570-574 ◽  
Author(s):  
Akinori Yamanaka
Keyword(s):  
Plastic Deformation ◽  
Crystal Plasticity ◽  
Phase Field ◽  
Deformation Behavior ◽  
Fast Fourier Transformation ◽  
Dual Phase ◽  
Dp Steel ◽  
3D Microstructure ◽  
Plastic Deformation Behavior ◽  
Multi Phase

The plastic deformation behavior of dual-phase (DP) steel is strongly affected by its underlying three-dimensional (3D) microstructural factors such as spatial distribution and morphology of ferrite and martensite phases. In this paper, we present a coupled simulation method by the multi-phase-field (MPF) model and the crystal plasticity fast Fourier transformation (CPFFT) model to investigate the 3D microstructure-dependent plastic deformation behavior of DP steel. The MPF model is employed to generate a 3D digital image of DP microstructure, which is utilized to create a 3D representative volume element (RVE). Furthermore, the CPFFT simulation of tensile deformation of DP steel is performed using the 3D RVE. Through the simulations, we demonstrate the stress and strain partitioning behaviors in DP steel depending on the 3D morphology of DP microstructure can be investigated consistently.

Study of the Titanium Alloy Deformation Behavior in Equal Channel Angular Extrusion

2007 ◽  
Vol 345-346 ◽  
pp. 177-180 ◽  
Author(s):  
Dyi Cheng Chen ◽  
Yi Ju Li ◽  
Gow Yi Tzou
Keyword(s):  
Plastic Deformation ◽  
Titanium Alloy ◽  
Deformation Behavior ◽  
Equal Channel Angular Extrusion ◽  
Effective Strain ◽  
Processing Conditions ◽  
Rigid Plastic ◽  
Die Geometry ◽  
Extrusion Processing ◽  
Plastic Deformation Behavior

The shear plastic deformation behavior of a material during equal channel angular (ECA) extrusion is governed primarily by the die geometry, the material properties, and the processing conditions. Using commercial DEFORMTM 2D rigid-plastic finite element code, this study investigates the plastic deformation behavior of Ti-6Al-4V titanium alloy during 1- and 2-turn ECA extrusion processing in dies containing right-angle turns. The simulations investigate the distributions of the billet mesh, effective stress and effective strain under various processing conditions. The respective influences of the channel curvatures in the inner and outer regions of the channel corner are systematically examined. The numerical results provide valuable insights into the shear plastic deformation behavior of Ti-6Al-4V titanium alloy during ECA extrusion.

Sign in / Sign up

Export Citation Format

Share Document