scholarly journals Role of Rotating Cylinder toward Mixed Convection inside a Wavy Heated Cavity via Two-Phase Nanofluid Concept

Nanomaterials ◽  
2020 ◽  
Vol 10 (6) ◽  
pp. 1138 ◽  
Author(s):  
Ammar I. Alsabery ◽  
Mohammad Ghalambaz ◽  
Taher Armaghani ◽  
Ali Chamkha ◽  
Ishak Hashim ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Mixed Convection ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Volume Fraction ◽  
Rotating Cylinder ◽  
Alumina Nanoparticles ◽  
Optimum Number ◽  
Two Phase ◽  
Rotation Direction

The mixed convection two-phase flow and heat transfer of nanofluids were addressed within a wavy wall enclosure containing a solid rotating cylinder. The annulus area between the cylinder and the enclosure was filled with water-alumina nanofluid. Buongiorno’s model was applied to assess the local distribution of nanoparticles in the host fluid. The governing equations for the mass conservation of nanofluid, nanoparticles, and energy conservation in the nanofluid and the rotating cylinder were carried out and converted to a non-dimensional pattern. The finite element technique was utilized for solving the equations numerically. The influence of the undulations, Richardson number, the volume fraction of nanoparticles, rotation direction, and the size of the rotating cylinder were examined on the streamlines, heat transfer rate, and the distribution of nanoparticles. The Brownian motion and thermophoresis forces induced a notable distribution of nanoparticles in the enclosure. The best heat transfer rate was observed for 3% volume fraction of alumina nanoparticles. The optimum number of undulations for the best heat transfer rate depends on the rotation direction of the cylinder. In the case of counterclockwise rotation of the cylinder, a single undulation leads to the best heat transfer rate for nanoparticles volume fraction about 3%. The increase of undulations number traps more nanoparticles near the wavy surface.

Numerical simulation of water/alumina nanofluid mixed convection in square lid-driven cavity

2019 ◽  
Vol 30 (5) ◽  
pp. 2781-2807
Author(s):  
Davood Toghraie ◽  
Ehsan Shirani
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Mixed Convection ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Richardson Number ◽  
Hartmann Number ◽  
Two Phase ◽  
Content Type ◽  
Driven Cavity

Purpose The purpose of this paper is to investigate the mixed convection of a two-phase water–aluminum oxide nanofluid in a cavity under a uniform magnetic field. Design/methodology/approach The upper wall of the cavity is cold and the lower wall is warm. The effects of different values of Richardson number, Hartmann number, cavitation length and solid nanoparticles concentration on the flow and temperature field and heat transfer rate were evaluated. In this paper, the heat flux was assumed to be constant of 10 (W/m2) and the Reynolds number was assumed to be constant of 300 and the Hartmann number and the volume fraction of solid nanoparticles varied from 0 to 60 and 0 to 0.06, respectively. The Richardson number was considered to be 0.1, 1 and 5. Aspect ratios were 1, 1.5 and 2. Findings Comparison of the results of this paper with the results of the numerical and experimental studies of other researchers showed a good correlation. The results were presented in the form of velocity and temperature profiles, stream and isotherm lines and Nusselt numbers. The results showed that by increasing the Hartmann number, the heat transfer rate decreases. An increase from 0 to 20 in Hartmann number results in a 20 per cent decrease in Nusselt numbers, and by increasing the Hartmann number from 20 to 40, a 16 per cent decrease is observed in Nusselt number. Accordingly, it is inferred that by increasing the Hartmann number, the reduction in the Nusselt number is decreased. As the Richardson number increased, the heat transfer rate and, consequently, the Nusselt number increased. Therefore, an increase in the Richardson number results in an increase of the Nusselt number, that is, an increase in Richardson number from 0.1 to 1 and from 1 to 5 results in 37 and 47 per cent increase in Nusselt number, respectively. Originality/value Even though there have been numerous investigations conducted on convection in cavities under various configurations and boundary conditions, relatively few studies are conducted for the case of nanofluid mixed convection in square lid-driven cavity under the effect of magnetic field using two-phase model.

scholarly journals Premium jet cooling with two ribs over flat plate utilizing nanofluid mixed convection

2017 ◽  
Vol 21 (2) ◽  
pp. 963-976 ◽  
Author(s):  
Wael El-Maghlany ◽  
Mohamed Teamah ◽  
A.E. Kabeel ◽  
Ahmed Hanafy
Keyword(s):  
Heat Transfer ◽  
Numerical Simulation ◽  
Mixed Convection ◽  
Flat Plate ◽  
Heat Transfer Rate ◽  
Thermal Performance ◽  
Transfer Rate ◽  
Richardson Number ◽  
Volume Fraction ◽  
Solid Volume Fraction

In this study, a numerical simulation of the thermal performance of two ribs mounted over a horizontal flat plate and cooled by Cu-water nanofluid is performed. The plate is heated and maintained at a constant temperature and cooled by mixed convection of laminar flow at a relatively low temperature. The top wall is considered as an adiabatic condition. The effects of related parameters such as Richardson number (0.01 ? Ri ? 10), the solid volume fraction (0.01 ? ? ? 0.06), the distance ratio between the two ribs (d/W = 5, 10, and 15), and the rib height ratio (b/W = 1, 2, and 3) on the ribs thermal performance are studied. The numerical simulation results indicate that the heat transfer rate is significantly affected by the distance and the rib height. The heat transfer rate is improved by increasing the nanoparticles volume fraction. The influence of the solid volume fraction with the increase of heat transfer is more noticeable for lower values of the Richardson number. The numerical results are summarized in the effect of pertinent parameters on the average Nusselt number with the assistance of both streamlines and isothermal ones. Throughout the study, the Grashof and Prandtl numbers, for pure water are kept constant at 103 and 6.2, respectively. The numerical work was displayed out using, an in-house computational fluid dynamic code written in FORTRAN, which discretizes non-dimensional forms of the governing equations using the finite volume method and solves the resulting system of equations using Gauss-Seidal method utilizing a tri diagonal matrix algorithm.

Numerical analysis of mixed convection of different nanofluids in concentric annulus

2019 ◽  
Vol 29 (4) ◽  
pp. 1506-1525 ◽  
Author(s):  
Ahad Abedini ◽  
Saeed Emadoddin ◽  
Taher Armaghani
Keyword(s):  
Heat Transfer ◽  
Mixed Convection ◽  
Flow Pattern ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Volume Fraction ◽  
Convection Heat Transfer ◽  
Simple Algorithm ◽  
Content Type ◽  
Volume Method

Purpose This study aims to investigate the numerical analysis of mixed convection within the horizontal annulus in the presence of water-based fluid with nanoparticles of aluminum oxide, copper, silver and titanium oxide. Numerical solution is performed using a finite-volume method based on the SIMPLE algorithm, and the discretization of the equations is generally of the second order. Inner and outer cylinders have a constant temperature, and the inner cylinder temperature is higher than the outer one. The two cylinders can be rotated in both directions at a constant angular velocity. The effect of parameters such as Rayleigh, Richardson, Reynolds and the volume fraction of nanoparticles on heat transfer and flow pattern are investigated. The results show that the heat transfer rate increases with the increase of the Rayleigh number, as well as by increasing the volume fraction of the nanoparticles, the heat transfer rate increases, and this increase is about 8.25 per cent for 5 per cent volumetric fraction. Rotation of the cylinders reduces the overall heat transfer. Different directions of rotation have a great influence on the flow pattern and isotherms, and ultimately on heat transfer. The addition of nanoparticles does not have much effect on the flow pattern and isotherms, but it is quantitatively effective. The extracted results are in good agreement with previous works. Design/methodology/approach Studying mixed convection heat transfer in the horizontal annulus in the presence of a water-based fluid with aluminum oxide, copper, silver and titanium oxide nanoparticles is carried out quantitatively using a finite-volume method based on the SIMPLE algorithm. Findings Increasing the Rayleigh number increases the Nusselt number. Increasing the Richardson number increases heat transfer. Adding nanoparticles does not have much effect on the flow pattern but is effective quantitatively on heat transfer parameters. The addition of nanoparticles sometimes increases the heat transfer rate by about 8.25 per cent. In constant Rayleigh numbers, increasing the Reynolds number reduces heat transfer. The Rayleigh and Reynolds numbers greatly affect the isotherms and streamlines. In addition to the thermal conductivity of nanoparticles, the thermo-physical properties of nanoparticles has great effect in the formation of isotherms and streamlines and ultimately heat transfer. Originality/value Studying the effect of different direction of rotation on the isotherms and streamlines, as well as the comparison of different nanoparticles on mixed convection heat transfer in annulus.

Magnetohydrodynamic Mixed Convection of a Cu-Water Nanofluid in a Vertical Channel

2013 ◽  
Vol 135 (7) ◽  
Author(s):  
A. Raisi ◽  
S. M. Aminossadati ◽  
B. Ghasemi
Keyword(s):  
Magnetic Field ◽  
Heat Transfer ◽  
Mixed Convection ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Volume Fraction ◽  
Solid Volume Fraction ◽  
Convection Heat Transfer ◽  
Vertical Channel ◽  
Mixed Convection Heat Transfer

This technical brief numerically examines the mixed convection heat transfer of a Cu-water nanofluid in a parallel-plate vertical channel that is influenced by a magnetic field. An upward flow of Cu-water nanofluid enters the channel at a relatively low temperature and a uniform velocity. It is found that the magnetic field has dissimilar effects on the heat transfer rate at different Richardson numbers. The increase of solid volume fraction results in an increase of the heat transfer rate especially at low Richardson numbers.

scholarly journals Periodic mixed convection of a nanofluid in a cavity with top lid sinusoidal motion

2011 ◽  
Vol 225 (9) ◽  
pp. 2149-2160 ◽  
Author(s):  
A Karimipour ◽  
A H Nezhad ◽  
A Behzadmehr ◽  
S Alikhani ◽  
E Abedini
Keyword(s):  
Heat Transfer ◽  
Aspect Ratio ◽  
Mixed Convection ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Richardson Number ◽  
Volume Fraction ◽  
Temperature Profiles ◽  
Sinusoidal Motion ◽  
Periodic State

The periodic mixed convection of a water–copper nanofluid inside a rectangular cavity with aspect ratio of 3 is investigated numerically. The temperature of the bottom wall of the cavity is assumed greater than the temperature of the top lid which oscillates horizontally with the velocity defined as u =  u0 sin ( ωt). The effects of Richardson number, Ri, and volume fraction of nanoparticles on the flow and thermal behaviour of the nanofluid are investigated. Velocity, temperature profiles, and streamlines are presented. It is observed that when Ri < 1, heat transfer rate is much greater than when Ri > 1. The higher value of Ri corresponds to a lower value of the amplitude of the oscillation of Nu m in the steady periodic state. Moreover, increasing the volume fraction of the nanoparticles increases the heat transfer rate.

Manninen’s mixture model for conjugate conduction and mixed convection heat transfer of a nanofluid in a rotational/stationary circular enclosure

2020 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Faraz Hoseininejad ◽  
Saeed Dinarvand ◽  
Mohammad Eftekhari Yazdi
Keyword(s):  
Heat Transfer ◽  
Mixed Convection ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Volume Fraction ◽  
Convection Heat Transfer ◽  
Convection Heat ◽  
Content Type ◽  
Mixed Convection Heat Transfer ◽  
Conjugate Conduction

Purpose This study aims to investigate numerically the problem of conjugate conduction and mixed convection heat transfer of a nanofluid in a rotational/stationary circular enclosure using a two-phase mixture model. Design/methodology/approach Hot and cold surfaces on the wall or inside the enclosure (heater and cooler) are maintained at constant temperature of Th and Tc, respectively, whereas other parts are thermally insulated. To examine the effects of various parameters such as Richardson number (0.01 = Ri =100), thermal conductivity ratio of solid to base fluid (1 = Kr = 100), volume fraction of nanoparticle (0 = φ = 0.05), insertion of conductive covers (C.Cs) around the heater in a different shape (triangular, circular or square), segmentation and arrangement of the conductive blocks (C.Bs) and rotation direction of the enclosure on the flow structure and heat transfer rate, two-dimensional equations of mass, momentum and energy conservation, as well as volume fraction, are solved using finite volume method and Semi-Implicit Method for Pressure Linked Equations (SIMPLE) algorithm. Findings The results show that inserting C.C around heater can increase or decrease heat transfer rate, and it depends on thermal conductivity ratio of solid to pure fluid. Also, it is found that by the division of C.B and location of its portions in a horizontal configuration, heat transfer rate reduces. Moreover, it is observed that external heating and cooling of the enclosure causes enhancement of heat transfer relative to that of internal heating and cooling. Finally, results illustrate that under the condition that cylinders rotate in the same direction, the heat transfer rate increases as compared to those that rotate in the opposite direction. Hence rotation direction of cylinders can be used as a desired parameter for controlling heat transfer rate. Originality/value A comprehensive report of results for the problem of conjugate conduction and mixed convection heat transfer in a circular cylinder containing different shapes of C.C, conducting obstacle and heater and cooler has been presented. An efficient numerical technique has been developed to solve this problem. The achievements of this paper are purely original, and the numerical results were never published by any researcher.

scholarly journals Control temperature fluctuations in two-phase CuO-water nanofluid by transfiguration of the enclosures

2020 ◽  
pp. 334-334
Author(s):  
Hadi Pourziaei Araban ◽  
Javad Alinejad ◽  
Ganji Domiri
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Natural Convection ◽  
Heat Transfer Rate ◽  
Wall Temperature ◽  
Transfer Rate ◽  
Volume Fraction ◽  
Temperature Fields ◽  
Two Phase ◽  
Flux Boundary Condition

The innovation of this paper is to simulate two-phase nanofluid natural convection inside the transformable enclosure to control the heat transfer rate under different heat flux. Heat transfer of a two-phase CuO-water nanofluid in an enclosure under different heat flux has many industrial applications including energy storage systems, thermal control of electronic devices and cooling of radioactive waste containers. The Lattice Boltzmann Method based on the D2Q9 method has been utilized for modeling velocity and temperature fields. Streamlines, isotherms and nanoparticle volume fraction, have been investigated for control the heat transfer rate for several cases. The purpose of this feasibility study is to achieve uniform temperature profiles and Tmax < 50?C under different heat flux. Natural convection heat transfer in the rectangular and parallelogram enclosures with positive and negative angular adiabatic walls were simulated. The average wall temperature under heat flux boundary condition has been studied to predict optimal levels of effective factors to control the maximum wall temperature. The results illustrated parallelogram enclosures with positive angle of case 1 and case 3 and 4 with rectangular enclosures were best cases for considering physical conditions. Average of temperature for these cases were 37.9, 29.7 and 38.2, respectively.

scholarly journals Numerical Study of Mixed Convection of the Nanofluids in Two-Sided Lid-Driven Square Cavity with a Pair of Triangular Heating Cylinders

2016 ◽  
Vol 2016 ◽  
pp. 1-8 ◽  
Author(s):  
Zoubair Boulahia ◽  
Abderrahim Wakif ◽  
Rachid Sehaqui
Keyword(s):  
Heat Transfer ◽  
Mixed Convection ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Volume Fraction ◽  
Numerical Study ◽  
Simple Algorithm ◽  
Design Parameters ◽  
Rate Variation ◽  
Square Cavity

A numerical study is carried out concerning mixed convection of the nanofluid in two-sided lid-driven square cavity with a pair of triangular heat sources. The upper and bottom moving walls are thermally insulated while the left and right walls are cooled at constant temperature. Two-dimensional Navier-Stokes and energy equations are solved using the finite volume discretization method with SIMPLE algorithm. The method used is validated against previous works. Two cases were considered depending on the direction of moving walls. Effects of various design parameters such as Richardson number(0.1≤Ri≤100), nanoparticle volume fraction(0≤φ≤0.05), and size(25 nm≤dp≤145 nm)and type(Cu,Al2O3,TiO2)of nanoparticles on the heat transfer rate are investigated. The results of this investigation illustrate that, by reducing the diameter of the nanoparticles andRi, the heat transfer rate increases. Moreover, it is found that by changing horizontal direction of the moving walls the heat transfer rate variation is negligible.

Sign in / Sign up

Export Citation Format

Share Document