scholarly journals Investigation of Hydrogen Content and Dilution Effect on Syngas/Air Premixed Turbulent Flame Using OH Planar Laser-Induced Fluorescence

Processes ◽  
2021 ◽  
Vol 9 (11) ◽  
pp. 1894
Author(s):  
Li Yang ◽  
Wubin Weng ◽  
Yanqun Zhu ◽  
Yong He ◽  
Zhihua Wang ◽  
...  
Keyword(s):  
Hydrogen Content ◽  
Laminar Flame ◽  
Turbulent Flame ◽  
Laser Induced Fluorescence ◽  
Flame Speed ◽  
Laminar Flame Speed ◽  
High Hydrogen ◽  
Turbulent Flame Speed ◽  
Planar Laser Induced Fluorescence ◽  
Planar Laser

Syngas produced by gasification, which contains a high hydrogen content, has significant potential. The variation in the hydrogen content and dilution combustion are effective means to improve the steady combustion of syngas and reduce NOx emissions. OH planar laser-induced fluorescence technology (OH-PLIF) was applied in the present investigation of the turbulence of a premixed flame of syngas with varied compositions of H2/CO. The flame front structure and turbulent flame velocities of syngas with varied compositions and turbulent intensities were analyzed and calculated. Results showed that the trend in the turbulent flame speed with different hydrogen proportions and dilutions was similar to that of the laminar flame speed of the corresponding syngas. A higher hydrogen proportion induced a higher turbulent flame speed, higher OH concentration, and a smaller flame. Dilution had the opposite effect. Increasing the Reynolds number also increased the turbulent flame speed and OH concentration. In addition, the effect of the turbulence on the combustion of syngas was independent of the composition of syngas after the analysis of the ratio between the turbulent flame speed and the corresponding laminar flame speed, for the turbulent flames under low turbulent intensity. These research results provide a theoretical basis for the practical application of syngas with a complex composition in gas turbine power generation.

Measurements of Stretch Statistics at Flame Leading Points for High Hydrogen Content Fuels

2014 ◽  
Author(s):  
Andrew Marshall ◽  
Julia Lundrigan ◽  
Prabhakar Venkateswaran ◽  
Jerry Seitzman ◽  
Tim Lieuwen
Keyword(s):  
Flame Front ◽  
Hydrogen Content ◽  
Turbulent Flame ◽  
Flame Speed ◽  
Fuel Composition ◽  
Mean Flow ◽  
Tangential Strain ◽  
High Hydrogen ◽  
High Hydrogen Content ◽  
Turbulent Flame Speed

Fuel composition has a strong influence on the turbulent flame speed, even at very high turbulence intensities. An important implication of this result is that the turbulent flame speed cannot be extrapolated from one fuel to the next using only the laminar flame speed and turbulence intensity as scaling variables. This paper presents curvature and tangential strain rate statistics of premixed turbulent flames for high hydrogen content fuels. Global (unconditioned) stretch statistics are presented as well as measurements conditioned on the leading points of the flame front. These measurements are motivated by previous experimental and theoretical work that suggests the turbulent flame speed is controlled by the flame front characteristics at these points. The data were acquired with high speed particle image velocimetry (PIV) in a low swirl burner (LSB). We attained measurements for several H2:CO mixtures over a range of mean flow velocities and turbulence intensities. The results show that fuel composition has a systematic, yet weak effect on curvatures and tangential strain rates at the leading points. Instead, stretch statistics at the leading points are more strongly influenced by mean flow velocity and turbulence level. It has been argued that the increased turbulent flame speeds seen with increasing hydrogen content are the result of increasing flame stretch rates, and therefore SL,max values, at the flame leading points. However, the differences observed with changing fuel compositions are not significant enough to support this hypothesis. Additional analysis is needed to understand the physical mechanisms through which the turbulent flame speed is altered by fuel composition effects.

Three-dimensional computational fluid dynamics simulation of hydrogen engines using a turbulent flame speed closure combustion model

2012 ◽  
Vol 13 (5) ◽  
pp. 464-481 ◽  
Author(s):  
Udo Gerke ◽  
Konstantinos Boulouchos
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Laminar Flame ◽  
Turbulent Flame ◽  
Three Dimensional ◽  
Flame Speed ◽  
Combustion Model ◽  
Laminar Flame Speed ◽  
Release Rates ◽  
Turbulent Flame Speed

The mixture formation and combustion process of a hydrogen direct-injection internal combustion engine is computed using a modified version of a commercial three-dimensional computational fluid dynamics code. The aim of the work is the evaluation of hydrogen laminar flame speed correlations and turbulent flame speed closures with respect to combustion of premixed and stratified mixtures at various levels of air-to-fuel equivalence ratio. Heat-release rates derived from in-cylinder pressure traces are used for the validation of the combustion simulations. A turbulent combustion model with closures for a turbulent flame speed is investigated. The value of the computed heat-release rates mainly depends on the quality of laminar burning velocities and standard of turbulence quantities provided to the combustion model. Combustion simulations performed with experimentally derived laminar flame speed data give better results than those using laminar flame speeds obtained from a kinetic scheme. However, experimental data of hydrogen laminar flame speeds found in the literature are limited regarding the range of pressures, temperatures and air-to-fuel equivalence ratios, and do not comply with the demand of high-pressure engine-relevant conditions.

Turbulent Consumption Speed Scaling of H2/CO Blends

2011 ◽  
Author(s):  
Prabhakar Venkateswaran ◽  
Andrew D. Marshall ◽  
David R. Noble ◽  
Jerry M. Seitzman ◽  
Tim C. Lieuwen
Keyword(s):  
Laminar Flame ◽  
Turbulent Flame ◽  
Practical Interest ◽  
Flame Speed ◽  
Fuel Composition ◽  
Laminar Flame Speed ◽  
Volume Data ◽  
Mean Flow ◽  
Turbulent Flame Speed ◽  
Kinetic Calculations

This paper describes measurements and analysis of global turbulent consumption speeds, ST,GC, of hydrogen/carbon monoxide (H2/CO) mixtures. The turbulent flame properties of such mixtures are of fundamental interest because of their strong stretch sensitivity and of practical interest since they are the primary constituents of syngas fuels. Data are analyzed at mean flow velocities and turbulence intensities of 4 < U0 < 50 m/s and 1 < u′rms/SL,0 < 100, respectively, for H2/CO blends ranging from 30–90% H2 by volume. Data from two sets of experiments are reported. In the first, fuel blends ranging from 30–90% H2 and mixture equivalence ratio, Φ, were adjusted at each fuel composition to have nominally the same un-stretched laminar flame speed, SL,0. In the second set, equivalence ratios were varied at constant H2 levels. The data clearly corroborate results from other studies that show significant sensitivity of ST,GC to fuel composition. For example, at a fixed u′rms, ST,GC of a 90% H2 case (at Φ = 0.48) is a factor of three times larger than the baseline Φ = 0.9, CH4/air mixture that has the same SL,0 value. We also describe physics-based correlations of these data, using leading points concepts and detailed kinetic calculations of their stretch sensitivities. These results are used to develop an inequality for negative Markstein length flames that bounds the turbulent flame speed data and show that the data can be collapsed using the maximum stretched laminar flame speed, SL,max, rather than SL,0.

Measurements of Stretch Statistics at Flame Leading Points for High Hydrogen Content Fuels

2017 ◽  
Vol 139 (11) ◽  
Author(s):  
Andrew Marshall ◽  
Julia Lundrigan ◽  
Prabhakar Venkateswaran ◽  
Jerry Seitzman ◽  
Tim Lieuwen
Keyword(s):  
Flame Front ◽  
Hydrogen Content ◽  
Turbulent Flame ◽  
Flame Speed ◽  
Fuel Composition ◽  
Mean Flow ◽  
Tangential Strain ◽  
High Hydrogen ◽  
High Hydrogen Content ◽  
Turbulent Flame Speed

Fuel composition has a strong influence on the turbulent flame speed, even at very high turbulence intensities. An important implication of this result is that the turbulent flame speed cannot be extrapolated from one fuel to the next using only the laminar flame speed and turbulence intensity as scaling variables. This paper presents curvature and tangential strain rate statistics of premixed turbulent flames for high hydrogen content (HHC) fuels. Global (unconditioned) stretch statistics are presented as well as measurements conditioned on the leading points of the flame front. These measurements are motivated by previous experimental and theoretical work that suggests the turbulent flame speed is controlled by the flame front characteristics at these points. The data were acquired with high-speed particle image velocimetry (PIV) in a low-swirl burner (LSB). We attained measurements for several H2:CO mixtures over a range of mean flow velocities and turbulence intensities. The results show that fuel composition has a systematic, yet weak effect on curvatures and tangential strain rates at the leading points. Instead, stretch statistics at the leading points are more strongly influenced by mean flow velocity and turbulence level. It has been argued that the increased turbulent flame speeds seen with increasing hydrogen content are the result of increasing flame stretch rates, and therefore, SL,max values, at the flame leading points. However, the differences observed with changing fuel compositions are not significant enough to support this hypothesis. Additional analysis is needed to understand the physical mechanisms through which the turbulent flame speed is altered by fuel composition effects.

Fuel Variation Effects in Propagation and Stabilization of Turbulent Counter-Flow Premixed Flames

2018 ◽  
Author(s):  
Ehsan Abbasi-Atibeh ◽  
Sandeep Jella ◽  
Jeffrey M. Bergthorson
Keyword(s):  
High Speed ◽  
Laminar Flame ◽  
Turbulent Flame ◽  
Mass Diffusion ◽  
Flame Stabilization ◽  
Turbulent Flames ◽  
Flame Speed ◽  
Flame Surface ◽  
Differential Diffusion ◽  
Turbulent Flame Speed

Sensitivity to stretch and differential diffusion of chemical species are known to influence premixed flame propagation, even in the turbulent environment where mass diffusion can be greatly enhanced. In this context, it is convenient to characterize flames by their Lewis number (Le), a ratio of thermal-to-mass diffusion. The work reported in this paper describes a study of flame stabilization characteristics when the Le is varied. The test data is comprised of Le ≪ 1 (Hydrogen), Le ≈ 1 (Methane), and Le > 1 (Propane) flames stabilized at various turbulence levels. The experiments were carried out in a Hot exhaust Opposed-flow Turbulent Flame Rig (HOTFR), which consists of two axially-opposed, symmetric turbulent round jets. The stagnation plane between the two jets allows the aerodynamic stabilization of a flame, and clearly identifies fuel influences on turbulent flames. Furthermore, high-speed Particle Image Velocimetry (PIV), using oil droplet seeding, allowed simultaneous recordings of velocity (mean and rms) and flame surface position. These experiments, along with data processing tools developed through this study, illustrated that in the mixtures with Le ≪ 1, turbulent flame speed increases considerably compared to the laminar flame speed due to differential diffusion effects, where higher burning rates compensate for the steepening average velocity gradient, and keeps these flames almost stationary as bulk flow velocity increases. These experiments are suitable for validating the ability of turbulent combustion models to predict lifted, aerodynamically-stabilized flames. In the final part of this paper, we model the three fuels at two turbulence intensities using the FGM model in a RANS context. Computations reveal that the qualitative flame stabilization trends reproduce the effects of turbulence intensity, however, more accurate predictions are required to capture the influences of fuel variations and differential diffusion.

scholarly journals Evaluation of Reduced Kinetics in Simulation of Gasified Biomass Gas Combustion

2013 ◽  
Author(s):  
Xiaoxiang Zhang ◽  
Nur Farizan Munjat ◽  
Jeevan Jayasuriya ◽  
Reza Fakhrai ◽  
Torsten Fransson
Keyword(s):  
Gas Turbine ◽  
Chemical Kinetics ◽  
Cfd Simulation ◽  
Laminar Flame ◽  
Turbulent Flame ◽  
Flame Speed ◽  
Turbulent Flame Speed ◽  
Operation Conditions ◽  
Simulation Results ◽  
Gas Turbine Combustion

It is essentially important to use appropriate chemical kinetic models in the simulation process of gas turbine combustion. To integrate the detailed kinetics into complex combustion simulations has proven to be a computationally expensive task with tens to thousands of elementary reaction steps. It has been suggested that an appropriate simplified kinetics which are computationally efficient could be used instead. Therefore reduced kinetics are often used in CFD simulation of gas turbine combustion. At the same time, simplified kinetics for specific fuels and operation conditions need to be carefully selected to fulfill the accuracy requirements. The applicability of several simplified kinetics for premixed Gasified Biomass Gas (GBG) and air combustion are evaluated in this paper. The current work is motivated by the growing demand of gasified biomass gas (GBG) fueled combustion. Even though simplified kinetic schemes developed for hydrocarbon combustions are published by various researchers, there is little research has been found in literature to evaluate the ability of the simplified chemical kinetics for the GBG combustion. The numerical Simulation tool “CANTERA” is used in the current study for the comparison of both detailed and simplified chemical kinetics. A simulated gas mixture of CO/H2/CH4/CO2/N2 is used for the current evaluation, since the fluctuation of GBG components may have an unpredictable influence on the simulation results. The laminar flame speed has an important influence with flame stability, extinction limits and turbulent flame speed, here it is chosen as an indicator for validation. The simulation results are compared with the experimental data from the previous study [1] which is done by our colleagues. Water vapour which has shown a dilution effect in the experimental study are also put into concern for further validation. As the results indicate, the reduced kinetics which are developed for hydrocarbon or hydrogen combustion need to be highly optimized before using them for GBG combustion. Further optimization of the reduced kinetics is done for GBG and moderate results are achieved using the optimized kinetics compared with the detailed combustion kinetics.

Modeling of Inhomogeneously Premixed Combustion With an Extended TFC Model

2000 ◽  
Vol 124 (1) ◽  
pp. 58-65 ◽  
Author(s):  
W. Polifke ◽  
P. Flohr ◽  
M. Brandt
Keyword(s):  
Laminar Flame ◽  
Mixture Fraction ◽  
Turbulent Flame ◽  
Flame Temperature ◽  
Flame Speed ◽  
Premixed Combustion ◽  
Combustion Stability ◽  
Model Parameters ◽  
Turbulent Flame Speed ◽  
Functional Relationships

In many practical applications, so-called premixed burners do not achieve perfect premixing of fuel and air. Instead, fuel injection pressure is limited, the permissible burner pressure drop is small and mixing lengths are curtailed to reduce the danger of flashback. Furthermore, internal or external piloting is frequently employed to improve combustion stability, while part-load operation often requires burner staging, where neighboring burners operate with unequal fuel/air equivalence ratios. In this report, an extension of the turbulent flame speed closure (TFC) model for highly turbulent premixed combustion is presented, which allows application of the model to the case of inhomogeneously premixed combustion. The extension is quite straightforward, i.e., the dependence of model parameters on mixture fraction is accounted for by providing appropriate lookup tables or functional relationships to the model. The model parameters determined in this way are adiabatic flame temperature, laminar flame speed and critical gradient. The model has been validated against a test case from the open literature and applied to an externally piloted industrial gas turbine burner with good success.

Visualization of Turbulent Flame Fronts with Planar Laser-Induced Fluorescence

Science ◽  
1984 ◽  
Vol 224 (4647) ◽  
pp. 382-384 ◽  
Author(s):  
G. KYCHAKOFF ◽  
R. D. HOWE ◽  
R. K. HANSON ◽  
M. C. DRAKE ◽  
R. W. PITZ ◽  
...  
Keyword(s):  
Turbulent Flame ◽  
Laser Induced Fluorescence ◽  
Planar Laser Induced Fluorescence ◽  
Planar Laser
Sign in / Sign up

Export Citation Format

Share Document