scholarly journals Modelado y simulación CFD de un sistema de refrigeración para el almacenamiento de vacunas contra la Influenza Estacional

2019 ◽  
pp. 12-18
Author(s):  
Julio Valle-Hernández ◽  
Joanna Díaz-Monroy ◽  
Britania Junery Lozano-Olmedo ◽  
Apolo Rojas-Ávila
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Storage Time ◽  
Seasonal Influenza ◽  
Storage Temperature ◽  
Positive Impact ◽  
Influenza Vaccines ◽  
Seasonal Influenza Vaccine ◽  
Computational Fluid Dynamics Cfd ◽  
Vaccination Campaigns

It is very important to carry out vaccination campaigns in the marginalized areas of our country, because they are more vulnerable to contracting diseases, but to do the appropriate containers are needed so that they arrive with their properties and to protect each person. The Seasonal Influenza vaccine is transported in portable refrigerators at a temperature of 2 and 8 ° C, and the storage time is within 3 and 7 days for the first and 12 to 36 hours for the second. This paper presents the modeling and simulation by Computational Fluid Dynamics (CFD) of a refrigerated system, from thermoelectric cells, for the storage of influenza vaccines. The results show the temperature distribution within the refrigerated system and the transfer of heat in each container element, as well as the most appropriate arrangement to keep each vaccine to the optimal storage temperature. Being able to count on portable systems that allow the optimal transfer of vaccines keeping refrigerated in a constant way would have a positive impact on the health of people who live in marginalized areas.

Aerodynamic Analysis of a Vehicle Tanker

2009 ◽  
Vol 131 (4) ◽  
Author(s):  
Ramon Miralbes Buil ◽  
Luis Castejon Herrer
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Drag Coefficient ◽  
Aerodynamic Drag ◽  
Positive Impact ◽  
Aerodynamic Resistance ◽  
Independent Contribution ◽  
Aerodynamic Drag Coefficient ◽  
Computational Fluid Dynamics Cfd ◽  
Selection Of

The aim of this article is the presentation of a series of aerodynamic improvements for semitrailer tankers, which reduce the aerodynamic resistance of these vehicles, and, consequently, result in a positive impact on fuel consumption, which is substantially reduced (up to 11%). To make the analysis the computational fluid dynamics (CFD) methodology, using FLUENT, has been used since it allows simulating some geometries and modifications of the geometry without making physical prototypes that considerably increase the time and the economical resources needed. Three improvements are studied: the aerodynamic front, the undercarriage skirt, and the final box adaptor. First they are studied in isolation, so that the independent contribution of each improvement can be appreciated, while helping in the selection of the most convenient one. With the aerodynamic front the drag coefficient has a reduction of 6.13%, with the underskirt 9.6%, and with the boat tail 7.72%. Finally, all the improvements are jointly examined, resulting in a decrease of up to 23% in aerodynamic drag coefficient.

Efficiency prediction for storage chambers using computational fluid dynamics

1996 ◽  
Vol 33 (9) ◽  
pp. 163-170 ◽  
Author(s):  
Virginia R. Stovin ◽  
Adrian J. Saul
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Shear Stress ◽  
Particle Tracking ◽  
Critical Value ◽  
Complex Geometries ◽  
Bed Shear Stress ◽  
Breadth Ratio ◽  
Computational Fluid Dynamics Cfd ◽  
Simulated Flow

Research was undertaken in order to identify possible methodologies for the prediction of sedimentation in storage chambers based on computational fluid dynamics (CFD). The Fluent CFD software was used to establish a numerical model of the flow field, on which further analysis was undertaken. Sedimentation was estimated from the simulated flow fields by two different methods. The first approach used the simulation to predict the bed shear stress distribution, with deposition being assumed for areas where the bed shear stress fell below a critical value (τcd). The value of τcd had previously been determined in the laboratory. Efficiency was then calculated as a function of the proportion of the chamber bed for which deposition had been predicted. The second method used the particle tracking facility in Fluent and efficiency was calculated from the proportion of particles that remained within the chamber. The results from the two techniques for efficiency are compared to data collected in a laboratory chamber. Three further simulations were then undertaken in order to investigate the influence of length to breadth ratio on chamber performance. The methodology presented here could be applied to complex geometries and full scale installations.

Improvement of real-scale raceway bioreactors for microalgae production using Computational Fluid Dynamics (CFD)

2021 ◽  
Vol 54 ◽  
pp. 102207
Author(s):  
Cristian Inostroza ◽  
Alessandro Solimeno ◽  
Joan García ◽  
José M. Fernández-Sevilla ◽  
F. Gabriel Acién
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Computational Fluid Dynamics Cfd ◽  
Real Scale

scholarly journals Design of Novel Flash Ironmaking Reactors for Greatly Reduced Energy Consumption and CO2 Emissions

Metals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 332
Author(s):  
Hong Yong Sohn ◽  
De-Qiu Fan ◽  
Amr Abdelghany
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Large Diameter ◽  
Reduction Reaction ◽  
The Novel ◽  
Height Ratio ◽  
Fine Iron ◽  
Computational Fluid Dynamics Cfd ◽  
High Reduction ◽  
Iron Ore Concentrate

The development of a novel ironmaking technology based on fine iron ore concentrate in a flash reactor is summarized. The design of potential industrial reactors for flash ironmaking based on the computational fluid dynamics technique is described. Overall, this simulation work has shown that the size of the reactor used in the novel flash ironmaking technology (FIT) can be quite reasonable vis-à-vis the blast furnaces. A flash reactor of 12 m diameter and 35 m height with a single burner operating at atmospheric pressure would produce 1.0 million tons of iron per year. The height can be further reduced by either using multiple burners, preheating the feed gas, or both. The computational fluid dynamics (CFD)-based design of potential industrial reactors for flash ironmaking pointed to a number of features that should be incorporated. The flow field should be designed in such a way that a larger portion of the reactor is used for the reduction reaction but at the same time excessive collision of particles with the wall must be avoided. Further, a large diameter-to-height ratio that still allows a high reduction degree should be used from the viewpoint of decreased heat loss. This may require the incorporation of multiple burners and solid feeding ports.

scholarly journals Morphological and Hemodynamic Changes during Cerebral Aneurysm Growth

2021 ◽  
Vol 11 (4) ◽  
pp. 520
Author(s):  
Emily R. Nordahl ◽  
Susheil Uthamaraj ◽  
Kendall D. Dennis ◽  
Alena Sejkorová ◽  
Aleš Hejčl ◽  
...  
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Kinetic Energy ◽  
Swirling Flow ◽  
Morphological Changes ◽  
Cerebral Aneurysms ◽  
Patient Specific ◽  
Aneurysm Wall ◽  
Aneurysm Growth ◽  
Computational Fluid Dynamics Cfd

Computational fluid dynamics (CFD) has grown as a tool to help understand the hemodynamic properties related to the rupture of cerebral aneurysms. Few of these studies deal specifically with aneurysm growth and most only use a single time instance within the aneurysm growth history. The present retrospective study investigated four patient-specific aneurysms, once at initial diagnosis and then at follow-up, to analyze hemodynamic and morphological changes. Aneurysm geometries were segmented via the medical image processing software Mimics. The geometries were meshed and a computational fluid dynamics (CFD) analysis was performed using ANSYS. Results showed that major geometry bulk growth occurred in areas of low wall shear stress (WSS). Wall shape remodeling near neck impingement regions occurred in areas with large gradients of WSS and oscillatory shear index. This study found that growth occurred in areas where low WSS was accompanied by high velocity gradients between the aneurysm wall and large swirling flow structures. A new finding was that all cases showed an increase in kinetic energy from the first time point to the second, and this change in kinetic energy seems correlated to the change in aneurysm volume.

Sign in / Sign up

Export Citation Format

Share Document