IMPROVEMENT OF OFFICIAL CHARACTERISTICS OF THE SURFACE LAYER DETAILS BY APPLICATION OF SURFACE PLASTIC DEFORMATION AND GASODYNAMYNAMYNAMINE

The article investigates changes in the characteristics of the surface layers of parts processed by methods of surface plastic deformation (SPD). It is shown that at SPD the strength and hardness characteristics of the material increase and residual compression stresses are formed. On the basis of the study of the stress-strain state of the material at the SPD, its non-monotonicity is established, which is manifested in the gradual change of sign of the components of deformations and stresses. In this regard, a tensor-nonlinear damage accumulation model was used to evaluate the deformability of the material, which takes into account the directional nature of the damage and the anisotropy of the plasticity of the deformed metal. Based on this model, an expression was obtained to determine the plasticity resource used in the case of multi-stage SPD. According to the results of the calculations, it is established that the maximum plasticity resource used in the SPD is at a depth of approximately 0.1 of the diameter of the plastic footprint of the tool, and destruction at full exhaustion of the plasticity resource occurs in the form of peeling of thin plates of appropriate thickness. Recommendations for displacement of the most reinforced layers to the surface of the workpiece are developed, as well as recommendations for limiting deformation by the amount of plasticity resource used. The conducted research allows to assign the optimal modes of SPD at the stage of technological process design. A device for cold gas-dynamic spraying was developed and the possibility of creating antifriction sections using it was investigated. Graphs of dependence of geometrical parameters of the deposited layer on the sputtering distance are constructed and methods and schemes of preparation for deposition of the surface of the workpiece using SPD methods are developed. Experimental cold gas-dynamic spraying was carried out and optimal parameters of the process of spraying of antifriction layers of bronze and metal polymers (pressure, and the temperature of the compressed air and the temperature of the workpiece) on the formed roller surface were determined. A new concept of increasing the contact strength and durability of friction pairs is proposed.

Download Full-text

INCREASING OF THE DURABILITY OF DETAILS WORKING UNDER REPEATABLE- LOADS

Vibrations in engineering and technology ◽

10.37128/2306-8744-2020-1-1 ◽

2020 ◽

pp. 5-14

Author(s):

Viktor Matviychuk ◽

Oleg Gaidamak

Keyword(s):

Surface Layer ◽

Surface Plastic Deformation ◽

Cold Gas Dynamic Spraying ◽

Surface Plastic ◽

Dynamic Coating ◽

Compressive Stresses ◽

Gas Dynamic ◽

Air Stream ◽

Coating Methods ◽

Cold Gas

The article develops processes of increase the durability of parts operating under repeated loads, by justifying the parameters of surface plastic deformation (SPD) and cold gas-dynamic coating. The influence on the depth of the reinforced surface layer, the nature of the distribution of the stress-strain state of the material and residual compressive stresses, as well as the value of the used plasticity of the metal, the parameters of the SPD process. The hypothesis is substantiated that the main factor in the formation of residual compressive stresses during SPD is the decrease in metal density, which is associated with the use of the plasticity resource. The model of definition of the used resource of plasticity of metals at SPD is developed, that allows to provide qualitative characteristics of a surface layer of details. Methods for shifting the layer with maximum hardening and residual compressive stresses to the surface of the part by using a deformable tool of smaller dimensions in subsequent passes and gas-dynamic coating before SPD. The vast majority of traditional gas-thermal coating methods occur at significant temperature effects on the surface of the part, which is unacceptable for the surface treated by SPD methods. Cold gas-dynamic spraying provides an allowable temperature regime for the creation of special auxiliary coatings while maintaining the properties of the surface treated by SPD methods. The technology of gas-dynamic coating includes heating the compressed gas (air), feeding it into the nozzle and forming a supersonic air stream in this nozzle, introducing a powder material into this stream, accelerating this material in the nozzle by a supersonic air flow and directing it to the surface of the workpiece. As a result, a special auxiliary coating is formed on the surface of the product, which provides optimal parameters of the SPD process.

Download Full-text

INCREASING THE DURABILITY OF DETAILS TO WORK UNDER REPEATABLE LOADS

Vibrations in engineering and technology ◽

10.37128/2306-8744-2020-3-2 ◽

2020 ◽

pp. 15-24

Author(s):

Viktor Matviychuk ◽

Oleg Gaidamak

Keyword(s):

Surface Layer ◽

Surface Plastic Deformation ◽

Cold Gas Dynamic Spraying ◽

Surface Plastic ◽

Dynamic Coating ◽

Compressive Stresses ◽

Gas Dynamic ◽

Coating Methods ◽

Copper Aluminum ◽

Cold Gas

The article presents the results of the development of processes to improve the performance of parts operating under repeated variable loads, taking into account the reasonable parameters of surface plastic deformation (SPD) and cold gas-dynamic spraying of coatings. The influence on the parameters of the working surface layer, the nature of the distribution of the stress-strain state of the surface layer of material and residual compressive stresses, as well as the values of the used resource of plasticity of the surface layer of the workpiece, the parameters of the SPD process. The article shows that the main factor in the formation of residual compressive stresses during SPD is the decrease in the density of the surface layer of the workpiece, which is associated with the use of the plasticity resource. The model of calculation of the used resource of plasticity of material of preparation at SPD which allows to provide the improved quality of a surface layer of details is offered. A method of moving the workpiece layers with maximum hardening and residual compression stresses to the surface of the part by applying a deforming tool of reduced size in the following passes with coating the surface of the part with gas-dynamic spraying before SPD. Cold gas-dynamic coating by spraying, in contrast to most known gas-thermal coating methods that take place under significant temperature effects on the surface of the part, which is unacceptable for surfaces treated by SPD methods, provides a permissible temperature regime for creating special auxiliary coatings while preserving surface properties SPD. The technology of gas-dynamic coating by spraying includes heating the compressed gas (air), directing it into the nozzle and forming in this nozzle supersonic air-powder flow, sprayed material (copper, aluminum), acceleration of this powder material to supersonic speeds and directing it to the surface of the processed product. As a result, a special auxiliary coating (copper or aluminum) is formed on the surface of the product, which improves the parameters of the SPD process.

Download Full-text

Determination of Geometrical Parameters Contact Zone for Detail Machining Surface Plastic Deformation

Procedia Engineering ◽

10.1016/j.proeng.2017.10.665 ◽

2017 ◽

Vol 206 ◽

pp. 1482-1487

Author(s):

Y.N. Oteny ◽

V.F. Kazak ◽

E.V. Morozova

Keyword(s):

Plastic Deformation ◽

Contact Zone ◽

Surface Plastic Deformation ◽

Geometrical Parameters ◽

Surface Plastic

Download Full-text

Finish-strengthening treatment with surface-plastic deformation

Science intensive technologies in mechanical engineering ◽

10.30987/2223-4608-2021-4-3-9 ◽

2021 ◽

Vol 2021 (4) ◽

pp. 3-9

Author(s):

Roman Gurov ◽

Andrey Shcherbakov

Keyword(s):

Plastic Deformation ◽

Surface Layer ◽

Quality Criteria ◽

Surface Plastic Deformation ◽

Quality Parameters ◽

Geometrical Parameters ◽

Surface Plastic ◽

Processing Modes ◽

Definition Of ◽

Surface Layer Quality

There are offered dependences for the definition of parameters formed for surface layer quality when finishing and finish-strengthening with surface-plastic deformation, for the definition of processing modes, tool geometrical parameters taking into account initial parameters of surface layer quality. Criteria for the choice of the processing method ensuring quality parameters required for a surface layer and surface operation properties are offered.

Download Full-text

New methods for surface plastic deformation of low-rigidity cylindrical machine parts

Science intensive technologies in mechanical engineering ◽

10.30987/article_5b53640219a6a8.67244170 ◽

2018 ◽

Vol 2018 (8) ◽

pp. 16-24 ◽

Cited By ~ 1

Author(s):

Семен Зайдес ◽

Semen Zaides

Keyword(s):

Plastic Deformation ◽

Surface Plastic Deformation ◽

Surface Plastic ◽

High Productivity ◽

Surface Strengthening ◽

New Methods ◽

Machine Parts

Technological potentialities at finish-strengthening processing of low-rigid parts of shaft- and axle types with local ways of machining impact are rather limited. In the paper there are considered new ways for strengthening allowing obtaining qualitative surface strengthening in machine parts at high productivity of an engineering procedure.

Download Full-text

Plastic deformation of collector plates at electric motor repair

10.36652/0042-4633-2020-5-79-82 ◽

2020 ◽

pp. 79-82

Author(s):

D.YU. Belan ◽

G.B. Toder ◽

K.V. Averkov ◽

YU.V. Titov

Keyword(s):

Plastic Deformation ◽

Electric Motor ◽

Roughness Parameter ◽

Surface Plastic Deformation ◽

Analytical Dependence ◽

Surface Plastic ◽

Machined Surface ◽

Tool Surface ◽

Diamond Burnishing ◽

Traction Electric Motor

A tool was developed for smoothing the plates of an electric motor collector. An analytical dependence of the roughness parameter of the machined surface on the force applied to the tool is obtained. Keywords traction electric motor, collector, diamond burnishing tool, surface-plastic deformation, repair, roughness. [email protected]

Download Full-text