Measurement of the Dynamic Transmission Error of Helical Gears by the Accelerometers

2003 ◽  
Vol 27 (10) ◽  
pp. 1720-1727
Keyword(s):  
Transmission Error ◽  
Helical Gears ◽  
Dynamic Transmission Error

The Effect of Tooth Wear on the Dynamic Transmission Error of Helical Gears with Smaller Number of Pinion Teeth

2014 ◽  
Vol 657 ◽  
pp. 649-653 ◽  
Author(s):  
Virgil Atanasiu ◽  
Cezar Oprişan ◽  
Dumitru Leohchi
Keyword(s):  
Dynamic Contact ◽  
Tooth Wear ◽  
Transmission Error ◽  
Analytical Investigation ◽  
Helical Gear ◽  
Wear Depth ◽  
Contact Ratio ◽  
Mesh Stiffness ◽  
Helical Gears ◽  
Dynamic Transmission Error

The paper presents an analytical investigation of the effect of the tooth wear on the dynamic transmission error of helical gear pairs with small number of pinion teeth. Firstly, the dynamic analysis is conducted to investigate only the effect of the time-varying mesh stiffness on the variation of dynamic transmission error along the line of action. Then, the tooth wear effect on the dynamics of helical gear with small number of pinion teeth is being researched. In the analysis, instantaneous dynamic contact analysis is used in wear depth calculations. A comparative study was performed to investigate the relation between total contact ratio, mesh stiffness and dynamic transmission error of helical gear pairs with small number of teeth.

Gear transmission error outside the normal path of contact due to corner and top contact

1999 ◽  
Vol 213 (4) ◽  
pp. 389-400 ◽  
Author(s):  
R. G. Munro ◽  
L Morrish ◽  
D Palmer
Keyword(s):  
Dynamic Test ◽  
Theoretical Models ◽  
Transmission Error ◽  
Helical Gear ◽  
Gear Transmission ◽  
The Novel ◽  
Transmission Systems ◽  
Helical Gears ◽  
Tooth Stiffness ◽  
Top Contact

This paper is devoted to a phenomenon known as corner contact, or contact outside the normal path of contact, which can occur in spur and helical gear transmission systems under certain conditions. In this case, a change in position of the driven gear with respect to its theoretical position takes place, thus inducing a transmission error referred to here as the transmission error outside the normal path of contact (TEo.p.c). The paper deals with spur gears only, but the results are directly applicable to helical gears. It systematizes previous knowledge on this subject, suggests some further developments of the theory and introduces the novel phenomenon of top contact. The theoretical results are compared with experimental measurements using a single flank tester and a back-to-back dynamic test rig for spur and helical gears, and they are in good agreement. Convenient approximate equations for calculation of TEo.p.c suggested here are important for analysis of experimental data collected in the form of Harris maps. This will make possible the calculation of tooth stiffness values needed for use in theoretical models for spur and helical gear transmission systems.

scholarly journals Computerized Design and Generation of Low-Noise Helical Gears with Modified Surface Topology

1995 ◽  
Vol 117 (2A) ◽  
pp. 254-261 ◽  
Author(s):  
F. L. Litvin ◽  
N. X. Chen ◽  
J. Lu ◽  
R. F. Handschuh
Keyword(s):  
Gear Tooth ◽  
Error Function ◽  
Transmission Error ◽  
Low Noise ◽  
Surface Topology ◽  
Helical Gears ◽  
Transmission Errors ◽  
Bearing Contact ◽  
Pinion Gear ◽  
Tooth Surfaces

An approach for the design and generation of low-noise helical gears with localized bearing contact is proposed. The approach is applied to double circular arc helical gears and modified involute helical gears. The reduction of noise and vibration is achieved by application of a predesigned parabolic function of transmission errors that is able to absorb a discontinuous linear function of transmission errors caused by misalignment. The localization of the bearing contact is achieved by the mismatch of pinion-gear tooth surfaces. Computerized simulation of meshing and contact of the designed gears demonstrated that the proposed approach will produce a pair of gears that has a parabolic transmission error function even when misalignment is present. Numerical examples for illustration of the developed approach are given.

A Comparison of Analytical Predictions With Experimental Measurements of Transmission Error of Misaligned Loaded Gears

1992 ◽  
Author(s):  
Harsh Vinayak ◽  
Donald R. Houser
Keyword(s):  
Experimental Data ◽  
Load Distribution ◽  
Theoretical Calculations ◽  
Data Acquisition System ◽  
Transmission Error ◽  
Test Facility ◽  
Experimental Measurements ◽  
Gear Pair ◽  
Prediction Program ◽  
Dynamic Transmission Error

Abstract This paper deals with the experimental study of dynamic transmission error of a gear pair. Two aspects of the experiment are discussed : 1) design of the test facility and data acquisition system and 2) comparison of transmission error and load distribution with experimental data. Several gears were tested under varying misalignments. A prediction program LDP (Load distribution Program) was used for theoretical calculations of dynamic transmission error.

On the Correlation Between Dynamic Transmission Error and Dynamic Tooth Loads in Three-Dimensional Gear Systems

2015 ◽  
Author(s):  
Nina Sainte-Marie ◽  
Philippe Velex ◽  
Guillaume Roulois ◽  
Franck Marrot
Keyword(s):  
Experimental Evidence ◽  
Three Dimensional ◽  
Transmission Error ◽  
Test Rig ◽  
Transmission Errors ◽  
Linear Dependency ◽  
Lumped Parameter ◽  
Dynamic Transmission Error ◽  
Time Variations ◽  
The Relationship

A three-dimensional dynamic model is presented to simulate the dynamic behavior of single stage gears by using a combination of classic shaft, lumped parameter and specific 2-node gear elements. The mesh excitation formulation is based on transmission errors whose mathematical grounding is briefly described. The validity of the proposed methodology is assessed by comparison with experimental evidence from a test rig. The model is then employed to analyze the relationship between dynamic transmission errors and dynamic tooth loads or root stresses. It is shown that a linear dependency can be observed between the time variations of dynamic transmission error and tooth loading as long as the system can be assimilated to a torsional system but that this linear relationship tends to disappear when the influence of bending cannot be neglected.

Modified optimization and experimental investigation of transmission error, vibration and noise for double helical gears

2014 ◽  
Vol 22 (1) ◽  
pp. 108-120 ◽  
Author(s):  
Cheng Wang ◽  
Huan Yong Cui ◽  
Qing Ping Zhang ◽  
Wen Ming Wang
Keyword(s):  
Experimental Investigation ◽  
Transmission Error ◽  
Helical Gears

Low excitation spur gears with variable tip diameter

2021 ◽  
Vol 263 (5) ◽  
pp. 1275-1285
Author(s):  
Joshua Götz ◽  
Sebastian Sepp ◽  
Michael Otto ◽  
Karsten Stahl
Keyword(s):  
Transmission Error ◽  
Spur Gear ◽  
Low Noise ◽  
Spur Gears ◽  
Mesh Stiffness ◽  
Helical Gears ◽  
Axial Forces ◽  
Tooth Width ◽  
Drive Trains ◽  
Static Transmission Error

One important source of noise in drive trains are transmissions. In numerous applications, it is necessary to use helical instead of spur gear stages due to increased noise requirements. Besides a superior excitation behaviour, helical gears also show additional disadvantageous effects (e.g. axial forces and tilting moments), which have to be taken into account in the design process. Thus, a low noise spur gear stage could simplify design and meet the requirements of modern mechanical drive trains. The authors explore the possibility of combining the low noise properties of helical gears with the advantageous mechanical properties of spur gears by using spur gears with variable tip diameter along the tooth width. This allows the adjustment of the total length of active lines of action at the beginning and end of contact and acts as a mesh stiffness modification. For this reason, several spur gear designs are experimentally investigated and compared with regard to their excitation behaviour. The experiments are performed on a back-to-back test rig and include quasi-static transmission error measurements under load as well as dynamic torsional vibration measurements. The results show a significant improvement of the excitation behaviour for spur gears with variable tip diameter.

Sign in / Sign up

Export Citation Format

Share Document