scholarly journals Numerical Analysis of Natural Convection Heat Transfer Inside an Inverted T-Shaped Cavity Filled with Nanofluid

2021 ◽  
pp. 180-188
Author(s):  
Gopal Sen ◽  
Mohammad Ilias Inam
Keyword(s):  
Heat Transfer ◽  
Rayleigh Number ◽  
Aspect Ratio ◽  
Average Nusselt Number ◽  
Volume Fraction ◽  
Convection Heat Transfer ◽  
Heated Wall ◽  
Natural Convection Heat Transfer ◽  
Average Heat Transfer Coefficient ◽  
Rayleigh Numbers

This assessment is centered on the characteristics of natural convection heat transfer of Aluminium Oxide-Air nanofluid inside an inverted T-shaped enclosure with differentially heated sidewalls. The left edges of the enclosed cavity have been treated as a heated wall and are kept at a constant temperature. The right edges are also maintained at a constant temperature but lower than the heated wall. The top and bottom faces of the cavity have been considered adiabatic. The evaluation has been numerically investigated using ANSYS fluent. The effect of different significant parameters like volume fraction of nanoparticles, the shape of the enclosure, and Rayleigh number on the heat transfer characteristics inside an inverted T shape enclosure have been investigated. In this numerical analysis, a series of DNS simulations have been conducted for different Rayleigh numbers in the range of 103 to 106, the volume fraction of particles in the range 0≤ φ ≤0.1, and for the different aspect ratios for the inverted T shape have been conducted. The outcomes of this CFD analysis indicate a remarkable rise in the average heat transfer coefficient with the rising volume fraction of Al2O3 particles in the air. An increase of the average Nusselt number was also observed with the increase of Rayleigh number, but it drops slightly at a higher volume fraction of nanoparticles due to an increase in conductive heat transfer. For Rayleigh numbers ≥ 104, both the average Nusselt number and average heat transfer coefficient decrease up to a certain shape of the cavity aspect ratio. After that cavity aspect ratio, both the parameters value increase. But in the case of Rayleigh number = 103, both of the values decrease with the increase in the cavity aspect ratio.

Influence of Cu-Water and CNT-Water Nanofluid on Natural Convection Heat Transfer in a Triangular Solar Collector

2020 ◽  
Author(s):  
Didarul Ahasan Redwan ◽  
Md. Habibur Rahman ◽  
Hasib Ahmed Prince ◽  
Emdadul Haque Chowdhury ◽  
M. Ruhul Amin
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Rayleigh Number ◽  
Solar Collector ◽  
Average Nusselt Number ◽  
Volume Fraction ◽  
Solid Volume Fraction ◽  
Convection Heat Transfer ◽  
Natural Convection Heat Transfer ◽  
Convection Heat

Abstract A numerical study on natural convection heat transfer in a right triangular solar collector filled with CNT-water and Cuwater nanofluids has been conducted. The inclined wall and the bottom wall of the cavity are maintained at a relatively lower temperature (Tc), and higher temperature (Th), respectively, whereas the vertical wall, is kept adiabatic. The governing non-dimensional partial differential equations are solved by using the Galerkin weighted residual finite element method. The Rayleigh number (Ra) and the solid volume-fraction of nanoparticles (ϕ) are varied in the range of 103 ≤ Ra ≤ 106, and 0 ≤ ϕ ≤ 0.1, respectively, to carry out the parametric simulations within the laminar region. Corresponding thermal and flow fields are presented via isotherms and streamlines. Variations of average Nusselt number as a function of Rayleigh number have been examined for different solid volume-fraction of nanoparticles. It has been found that the natural convection heat transfer becomes stronger with the increment of solid volume fraction and Rayleigh number, but the strength of circulation reduces with increasing nanoparticles’ concentration at low Ra. Conduction mode dominates for lower Ra up to a certain limit of 104. It is also observed that when the solid volume fraction is increased from 0 to 0.1 for a particular Rayleigh number, the average Nusselt number is increased to a great extent, but surprisingly, the rate of increment is more pronounced at lower Ra. Moreover, it is seen that Cu-water nanofluid offers slightly better performance compared to CNT-water but the difference is very little, especially at lower Ra.

scholarly journals Prediction of Natural Convection Heat Transfer Phenomena of Nanofluids in Corrugated Annulus

2020 ◽  
Author(s):  
Sattar Aljobair ◽  
Akeel Abdullah Mohammed ◽  
Israa Alesbe
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Natural Convection ◽  
Rayleigh Number ◽  
Average Nusselt Number ◽  
Volume Fraction ◽  
Outer Cylinder ◽  
Convection Heat Transfer ◽  
Natural Convection Heat Transfer ◽  
Convection Heat

Abstract The natural convection heat transfer and fluid flow characteristic of water based Al2O3 nano-fluids in a symmetrical and unsymmetrical corrugated annulus enclosure has been studied numerically using CFD. The inner cylinder is heated isothermally while the outer cylinder is kept constant cold temperature. The study includes eight models of corrugated annulus enclosure with constant aspect ratio of 1.5. The governing equations of fluid motion and heat transfer are solved using stream-vorticity formulation in curvilinear coordinates. The range of solid volume fractions of nanoparticles extends from PHI=0 to 0.25, and Rayleigh number varies from 104 to 107. Streamlines, isotherms, local and average Nusselt number of inner and outer cylinder has been investigated in this study. Sixty-four correlations have been deduced for the average Nusselt number for the inner and outer cylinders as a function of Rayleigh number have been deduced for eight models and five values of volume fraction of nano particles with an accuracy range 6-12 %. The results show that, the average heat transfer rate increases significantly as particle volume fraction and Rayleigh number increase. Also, increase the number of undulations in unsymmetrical annuli reduces the heat transfer rates which remain higher than that in symmetrical annuli. There is no remarkable change in isotherms contour with increase of volume fraction of nanofluid.

scholarly journals Enhancement of natural convection heat transfer in a U-shaped cavity filled with Al2O3-water nanofluid

2012 ◽  
Vol 16 (5) ◽  
pp. 1317-1323 ◽  
Author(s):  
Ching-Chang Cho ◽  
Her-Terng Yau ◽  
Cha’o-Kuang Chen
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Natural Convection ◽  
Rayleigh Number ◽  
Volume Fraction ◽  
Convection Heat Transfer ◽  
Heated Wall ◽  
Natural Convection Heat Transfer ◽  
Convection Heat ◽  
The Mean

This paper investigates the natural convection heat transfer enhancement of Al2O3-water nanofluid in a U-shaped cavity. In performing the analysis, the governing equations are modeled using the Boussinesq approximation and are solved numerically using the finite-volume numerical method. The study examines the effects of the nanoparticle volume fraction, the Rayleigh number and the geometry parameters on the mean Nusselt number. The results show that for all values of the Rayleigh number, the mean Nusselt number increases as the volume fraction of nanoparticles increases. In addition, it is shown that for a given length of the heated wall, extending the length of the cooled wall can improve the heat transfer performance.

An Experimental Study on the Effect of Partition Angle on Free Convection Heat Transfer in a Partition Cavity by Laser Interferometry Method

2010 ◽  
Author(s):  
Tooraj Yousefi ◽  
Sajjad Mahmoodi Nezhad ◽  
Masood Bigharaz ◽  
Saeed Ebrahimi
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Rayleigh Number ◽  
Free Convection ◽  
Average Nusselt Number ◽  
Convection Heat Transfer ◽  
Laser Interferometry ◽  
Heated Wall ◽  
Convection Heat ◽  
Free Convection Heat

Steady state two-dimensional free convection heat transfer in a partitioned cavity with adiabatic horizontal and isothermally vertical walls and an adiabatic partition has been investigated experimentally. The experiments have been carried out using a Mach-Zehnder interferometer. The effects of the angel of the adiabatic partition and Rayleigh number on the heat transfer from the heated wall are investigated. Experiments are performed for the values of Rayleigh number based on the cavity side length in the range between 1.5×105 to 4.5×105 and various angle of the partition with respect to horizon from 0° to 90°. The results indicate that at each angle of the adiabatic partition, by increasing the Rayleigh number, the average Nusselt number and heat transfer increase and at each Rayleigh number, the maximum and the minimum heat transfer occur at θ=45° and θ=90°, respectively. A correlation based on the experimental data for the average Nusselt number of the heated wall as a function of Rayleigh number and the angel of the adiabatic partition is presented in the aforementioned ranges.

Investigation of heat transfer of MHD Al2O3/water nanofluid in an enclosure with a semicircular wall and a heating obstacle

2019 ◽  
Vol 30 (12) ◽  
pp. 1950105 ◽  
Author(s):  
Yuan Ma ◽  
Zhigang Yang
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Rayleigh Number ◽  
Flow Pattern ◽  
Average Nusselt Number ◽  
Hartmann Number ◽  
Volume Fraction ◽  
Convection Heat Transfer ◽  
Nanoparticle Volume Fraction ◽  
Number Formula

Lattice Boltzmann method (LBM) was used to simulate two-dimensional MHD Al2O3/water nanofluid flow and heat transfer in an enclosure with a semicircular wall and a triangular heating obstacle. The effects of nanoparticle volume fraction ([Formula: see text]), Rayleigh number [Formula: see text], Hartmann number [Formula: see text] and heating obstacle position (Cases 1–7) on flow pattern, temperature distribution and rate of heat transfer were investigated. The results show that with the enhancing Rayleigh number, the increasing nanoparticle volume fraction and the reducing Hartmann number, an enhancement in the average Nusselt number and the heat transfer appeared. The effect of Ha on the average Nu increases by increasing the Ra. It can also be found that the action of changing the heating obstacle position on the convection heat transfer is more important than that on the conduction heat transfer. The higher obstacle position in Cases 6 and 7 leads to the small value of the average Nusselt number. Moreover, the effect of Ha on average Nu in Case 1 at [Formula: see text] is more significant than other cases because the flow pattern in Case 1 is changed as increasing Ha.

scholarly journals Free convection of a nanofluid in a square cavity with a heat source on the bottom wall and partially cooled from sides

2014 ◽  
Vol 18 (suppl.2) ◽  
pp. 283-300 ◽  
Author(s):  
Mostafa Mahmoodi ◽  
Arani Abbasian ◽  
Sebdani Mazrouei ◽  
Saeed Nazari ◽  
Mohammad Akbari
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Fluid Flow ◽  
Rayleigh Number ◽  
Average Nusselt Number ◽  
Volume Fraction ◽  
Heat Sinks ◽  
Square Cavity ◽  
Flow And Heat Transfer ◽  
Rayleigh Numbers

The problem of free convection fluid flow and heat transfer in a square cavity with a flush mounted heat source on its bottom wall and two heat sinks on its vertical side walls has been investigated numerically. Via changing the location of the heat sinks, six different arrangements have been generated. The cavity was filled with Cu-water nanofluid. The governing equations were discretized using the finite volume method and SIMPLER algorithm. Using the developed code, a parametric study was undertaken, and effects of Rayleigh number, arrangements of the heat sinks and volume fraction of the nanoparticles on fluid flow and heat transfer inside the cavity were investigated. Also for the middle-middle heat sinks arrangement, capability of five different water based nanofluids on enhancement of the rate of heat transfer was examined and compared. From the obtained results it was found that the average Nusselt number, for all six different arrangements of the heat sinks, was an increasing function of the Rayleigh number and the volume fraction of the nanoparticles. Also it was found that at high Rayleigh numbers, maximum and minimum average Nusselt number occurred for middle-middle and top-bottom arrangement, respectively. Moreover it was found that for the middle-middle arrangement, at high Rayleigh numbers, maximum and minimum rate of heat transfer was obtained by Cu-water and TiO2-water nanofluids respectively.

Numerical Analysis of Natural Convection Heat Transfer From a Vertical Hollow Cylinder Suspended in Air

2018 ◽  
Vol 140 (5) ◽  
Author(s):  
Swastik Acharya ◽  
Sumit Agrawal ◽  
Sukanta K. Dash
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Natural Convection ◽  
Rayleigh Number ◽  
Hollow Cylinder ◽  
Outer Surface ◽  
Average Nusselt Number ◽  
Convection Heat Transfer ◽  
Natural Convection Heat Transfer ◽  
Convection Heat

Natural convection heat transfer from a vertical hollow cylinder suspended in air has been analyzed numerically by varying the Rayleigh number (Ra) in the laminar (104 ≤ Ra ≤ 108) regime. The simulations have been carried out by changing the ratio of length to pipe diameter (L/D) in the range of 0.05 ≤ L/D≤20. Full conservation equations have been solved numerically for a vertical hollow cylinder suspended in air using algebraic multigrid solver of fluent 13.0. The flow and the temperature field around the vertical hollow cylinder have been observed through velocity vectors and temperature contours for small and large L/D. It has been found that the average Nusselt number (Nu) for vertical hollow cylinder suspended in air increases with the increase in Rayleigh number (Ra) and the Nu for both the inner and the outer surface also increases with Ra. However, with the increase in L/D, average Nu for the outer surface increases almost linearly, whereas the average Nu for the inner surface decreases and attains asymptotic value at higher L/D for low Ra. In this study, the effect of parameters like L/D and Ra on Nu is analyzed, and a correlation for average Nusselt number has been developed for the laminar regime. These correlations are accurate to the level of ±6%.

scholarly journals Numerical investigation into natural convection heat transfer enhancement of copper-water nanofluid in a wavy wall enclosure

2012 ◽  
Vol 16 (5) ◽  
pp. 1309-1316 ◽  
Author(s):  
Ching-Chang Cho ◽  
Her-Terng Yau ◽  
Cha’o-Kuang Chen
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Rayleigh Number ◽  
Volume Fraction ◽  
Convection Heat Transfer ◽  
Natural Convection Heat Transfer ◽  
Wavy Wall ◽  
Convection Heat ◽  
Heat Transfer Characteristics ◽  
Transfer Characteristics

Numerical investigations are performed into the natural convection heat transfer characteristics within a wavy-wall enclosure filled with Cu-water nanofluid. In the paper, the bottom wall of the enclosure has a wavy geometry and is maintained at a constant high temperature, while the top wall is straight and is maintained at a constant low temperature. The left and right walls of the enclosure are both straight and insulated. In performing the simulation, the Boussinesq approximation is used to model the governing equations. The study examines the effect of the nanoparticle volume fraction, the Rayleigh number, the wave amplitude, and the wavelength on the heat transfer characteristics. It is shown that the heat transfer performance can be enhanced as the volume fraction of nanoparticles increases. It is also shown that for a given Rayleigh number, the heat transfer effect can be optimized via an appropriate changing of the geometry conditions.

Dimensionless Correlating-Equations for Predicting the Optimal Tilting Angle of Water-Filled Square and Shallow Enclosures Differentially Heated at Sides

2013 ◽  
Vol 394 ◽  
pp. 163-172
Author(s):  
Marta Cianfrini ◽  
Roberto de Lieto Vollaro ◽  
Alessandro Quintino ◽  
Massimo Corcione
Keyword(s):  
Heat Transfer ◽  
Rayleigh Number ◽  
Aspect Ratio ◽  
Convection Heat Transfer ◽  
Heated Wall ◽  
Tilting Angle ◽  
Shallow Cavities ◽  
Correlating Equations ◽  
Laminar Natural Convection ◽  
Dimensionless Correlations

Laminar natural convection heat transfer inside water-filled, tilted square and shallow cavities heated at one side and cooled at the opposite side, is studied numerically. A computational code based on the SIMPLE-C algorithm is used to solve the system of the mass, momentum and energy transfer governing equations. Simulations are performed using the Rayleigh number based on the length of the heated and cooled sides, the height-to-width aspect ratio of the enclosure, and the positive tilting angle with respect to the gravity vector (which corresponds to configurations with the heated wall facing upwards), as independent variables. It is found that the heat transfer performance has a peak at an optimal tilting angle which increases as the Rayleigh number is decreased and the aspect ratio is increased. On the basis of the results obtained, a set of dimensionless correlations is developed.

A study of natural convection heat transfer in a nanofluid filled enclosure with elliptic inner cylinder

2014 ◽  
Vol 24 (8) ◽  
pp. 1906-1927 ◽  
Author(s):  
M. Sheikholeslami ◽  
R. Ellahi ◽  
Mohsan Hassan ◽  
Soheil Soleimani
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Rayleigh Number ◽  
Volume Fraction ◽  
Convection Heat Transfer ◽  
Natural Convection Heat Transfer ◽  
Convection Heat ◽  
Transfer Enhancement ◽  
Content Type ◽  
Inclined Angle

Purpose – The purpose of this paper is to study the effects of natural convection heat transfer in a cold outer circular enclosure containing a hot inner elliptic circular cylinder. The fluid in the enclosure is Cu-water nanofluid. The main emphasis is to find the numerical treatment for the said mathematical model. The effects of Rayleigh number, inclined angle of elliptic inner cylinder, effective of thermal conductivity and viscosity of nanofluid, volume fraction of nanoparticles on the flow and heat transfer characteristics have been examined. Design/methodology/approach – A very effective and higher order numerical scheme Control Volume-based Finite Element Method (CVFEM) is used to solve the resulting coupled equations. The numerical investigation is carried out for different governing parameters namely; the Rayleigh number, nanoparticle volume fraction and inclined angle of elliptic inner cylinder. The effective thermal conductivity and viscosity of nanofluid are calculated using the Maxwell-Garnetts (MG) and Brinkman models, respectively. Findings – The results reveal that Nusselt number increases with an increase of nanoparticle volume fraction, Rayleigh numbers and inclination angle. Also it can be found that increasing Rayleigh number leads to a decrease in heat transfer enhancement. For high Rayleigh number the minimum heat transfer enhancement ratio occurs at. Originality/value – To the best of the authors’ knowledge, no such analysis is available in the literature which can describe the natural convection heat transfer in a nanofluid filled enclosure with elliptic inner cylinder by means of CVFEM.

Sign in / Sign up

Export Citation Format

Share Document