An Experimental Study on the Effect of Partition Angle on Free Convection Heat Transfer in a Partition Cavity by Laser Interferometry Method

2010 ◽  
Author(s):  
Tooraj Yousefi ◽  
Sajjad Mahmoodi Nezhad ◽  
Masood Bigharaz ◽  
Saeed Ebrahimi
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Rayleigh Number ◽  
Free Convection ◽  
Average Nusselt Number ◽  
Convection Heat Transfer ◽  
Laser Interferometry ◽  
Heated Wall ◽  
Convection Heat ◽  
Free Convection Heat

Steady state two-dimensional free convection heat transfer in a partitioned cavity with adiabatic horizontal and isothermally vertical walls and an adiabatic partition has been investigated experimentally. The experiments have been carried out using a Mach-Zehnder interferometer. The effects of the angel of the adiabatic partition and Rayleigh number on the heat transfer from the heated wall are investigated. Experiments are performed for the values of Rayleigh number based on the cavity side length in the range between 1.5×105 to 4.5×105 and various angle of the partition with respect to horizon from 0° to 90°. The results indicate that at each angle of the adiabatic partition, by increasing the Rayleigh number, the average Nusselt number and heat transfer increase and at each Rayleigh number, the maximum and the minimum heat transfer occur at θ=45° and θ=90°, respectively. A correlation based on the experimental data for the average Nusselt number of the heated wall as a function of Rayleigh number and the angel of the adiabatic partition is presented in the aforementioned ranges.

scholarly journals Free Convection Heat Transfer from Horizontal Cylinders

Energies ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 559
Author(s):  
Janusz T. Cieśliński ◽  
Slawomir Smolen ◽  
Dorota Sawicka
Keyword(s):  
Heat Transfer ◽  
Rayleigh Number ◽  
Free Convection ◽  
Convection Heat Transfer ◽  
Horizontal Tube ◽  
Correlation Equations ◽  
Convection Heat ◽  
Number Range ◽  
Heated Cylinder ◽  
Free Convection Heat

The results of experimental investigation of free convection heat transfer in a rectangular container are presented. The ability of the commonly accepted correlation equations to reproduce present experimental data was tested as well. It was assumed that the examined geometry fulfils the requirement of no-interaction between heated cylinder and bounded surfaces. In order to check this assumption recently published correlation equations that jointly describe the dependence of the average Nusselt number on Rayleigh number and confinement ratios were examined. As a heat source served electrically heated horizontal tube immersed in an ambient fluid. Experiments were performed with pure ethylene glycol (EG), distilled water (W), and a mixture of EG and water at 50%/50% by volume. A set of empirical correlation equations for the prediction of Nu numbers for Rayleigh number range 3.6 × 104 < Ra < 9.2 × 105 or 3.6 × 105 < Raq < 14.8 × 106 and Pr number range 4.5 ≤ Pr ≤ 160 has been developed. The proposed correlation equations are based on two characteristic lengths, i.e., cylinder diameter and boundary layer length.

A Comparison Between the Local Free Convection Heat Transfer Coefficients of Horizontal Cylinders in Vertical and Inclined Arrays

2006 ◽  
Author(s):  
Mehdi Ashjaee ◽  
Tooraj Yousefi
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Rayleigh Number ◽  
Free Convection ◽  
Convection Heat Transfer ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Horizontal Cylinder ◽  
Convection Heat ◽  
Free Convection Heat

Laminar free convection heat transfer from vertical and inclined arrays of horizontal isothermal cylinders in air was investigated experimentally and numerically. Experiments were carried out using Mach-Zehnder interferometer and the FLUENT code was used for numerical study. Investigation was performed for vertical and horizontal cylinder spacing from 2 to 5 and to 2 cylinder diameter respectively. The Rayleigh number based on the cylinder diameter varied between 103 and 3×103. The effect of vertical and horizontal cylinder spacing and Rayleigh number on the local heat transfer from each individual cylinder was investigated. It was seen that the local heat transfer coefficient of each cylinder strongly depends on its position relative to the others. This variation of the local heat transfer coefficient was explained by the interaction of plume’s temperature and velocity profiles.

scholarly journals Prediction of Natural Convection Heat Transfer Phenomena of Nanofluids in Corrugated Annulus

2020 ◽  
Author(s):  
Sattar Aljobair ◽  
Akeel Abdullah Mohammed ◽  
Israa Alesbe
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Natural Convection ◽  
Rayleigh Number ◽  
Average Nusselt Number ◽  
Volume Fraction ◽  
Outer Cylinder ◽  
Convection Heat Transfer ◽  
Natural Convection Heat Transfer ◽  
Convection Heat

Abstract The natural convection heat transfer and fluid flow characteristic of water based Al2O3 nano-fluids in a symmetrical and unsymmetrical corrugated annulus enclosure has been studied numerically using CFD. The inner cylinder is heated isothermally while the outer cylinder is kept constant cold temperature. The study includes eight models of corrugated annulus enclosure with constant aspect ratio of 1.5. The governing equations of fluid motion and heat transfer are solved using stream-vorticity formulation in curvilinear coordinates. The range of solid volume fractions of nanoparticles extends from PHI=0 to 0.25, and Rayleigh number varies from 104 to 107. Streamlines, isotherms, local and average Nusselt number of inner and outer cylinder has been investigated in this study. Sixty-four correlations have been deduced for the average Nusselt number for the inner and outer cylinders as a function of Rayleigh number have been deduced for eight models and five values of volume fraction of nano particles with an accuracy range 6-12 %. The results show that, the average heat transfer rate increases significantly as particle volume fraction and Rayleigh number increase. Also, increase the number of undulations in unsymmetrical annuli reduces the heat transfer rates which remain higher than that in symmetrical annuli. There is no remarkable change in isotherms contour with increase of volume fraction of nanofluid.

scholarly journals Enhancement of natural convection heat transfer in a U-shaped cavity filled with Al2O3-water nanofluid

2012 ◽  
Vol 16 (5) ◽  
pp. 1317-1323 ◽  
Author(s):  
Ching-Chang Cho ◽  
Her-Terng Yau ◽  
Cha’o-Kuang Chen
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Natural Convection ◽  
Rayleigh Number ◽  
Volume Fraction ◽  
Convection Heat Transfer ◽  
Heated Wall ◽  
Natural Convection Heat Transfer ◽  
Convection Heat ◽  
The Mean

This paper investigates the natural convection heat transfer enhancement of Al2O3-water nanofluid in a U-shaped cavity. In performing the analysis, the governing equations are modeled using the Boussinesq approximation and are solved numerically using the finite-volume numerical method. The study examines the effects of the nanoparticle volume fraction, the Rayleigh number and the geometry parameters on the mean Nusselt number. The results show that for all values of the Rayleigh number, the mean Nusselt number increases as the volume fraction of nanoparticles increases. In addition, it is shown that for a given length of the heated wall, extending the length of the cooled wall can improve the heat transfer performance.

On Gaseous Free-Convection Heat Transfer With Well-Defined Boundary Conditions

2000 ◽  
Vol 122 (4) ◽  
pp. 661-668 ◽  
Author(s):  
M. R. D. Davies ◽  
D. T. Newport ◽  
T. M. Dalton
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Free Convection ◽  
Boundary Conditions ◽  
Convection Heat Transfer ◽  
Boussinesq Approximation ◽  
Horizontal Cylinder ◽  
Convection Heat ◽  
Variable Property ◽  
Free Convection Heat

The scaling of free convection heat transfer is investigated. The nondimensional groups for Boussinesq and fully compressible variable property free convection, driven by isothermal surfaces, are derived using a previously published novel method of dimensional analysis. Both flows are described by a different set of groups. The applicability of each flow description is experimentally investigated for the case of the isothermal horizontal cylinder in an air-filled isothermal enclosure. The approach taken to the boundary conditions differs from that of previous investigations. Here, it is argued that the best definition of the boundary conditions is achieved for heat exchange between the cylinder and the enclosure rather than the cylinder and an arbitrarily chosen fluid region. The enclosure temperature is shown both analytically and experimentally to affect the Nusselt number. The previously published view that the Boussinesq approximation has only a limited range of application is confirmed, and the groups derived for variable property compressible free convection are demonstrated to be correct experimentally. A new correlation for horizontal cylinder Nusselt number prediction is presented. [S0022-1481(00)01604-2]

scholarly journals Numerical Investigation of the Effect of Baffle Inclination Angle on Nanofluid Natural Convection Heat Transfer in A Square Enclosure

2019 ◽  
Vol 12 (2) ◽  
pp. 61-71 ◽  
Author(s):  
Barik AL-Muhjaa ◽  
Khaled Al-Farhany
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Nusselt Number ◽  
Fluid Flow ◽  
Natural Convection ◽  
Rayleigh Number ◽  
Average Nusselt Number ◽  
Solid Wall ◽  
Convection Heat Transfer ◽  
Convection Heat

The characteristics of the conjugate natural convection of (Al2O3-water) nanofluid inside differentially heated enclosure is numerically analyzed using COMSOL Multiphysics (5.3a). The enclosure consists of two vertical walls, the left wall has a thickness and maintain at a uniform hot temperature, while the opposite wall at cold temperature and the horizontal walls are isolated. A high thermal conductivity thin baffle has been added on the insulated bottom wall at a different inclination angles. The effect of the volume fractions of nanoparticles (f), Rayleigh number (Ra), solid wall thermal conductivity ratio (Kr), baffle incline angles (Ø) and the thickness of solid wall (D) on the isothermal lines, fluid flow patterns and the average Nusselt number (Nu)  has been investigated. At low Rayleigh number (Ra=103 to 104) the Isothermal lines are parallel with the vertical wall which is characteristic of conduction heat transfer. on the other hand, when Rayleigh number increase to (Ra=106),  the isotherms lines distribution in the inner fluid become parallel curves with the adiabatic horizontal walls of the enclosure and smooth in this case convection heat transfer becomes dominant. As the Rayleigh number further increases, the average Nusselt number enhance because of buoyancy force become stronger. In addition, the fluid flow within the space is affected by the presence of a fin attached to the lower wall that causes blockage and obstruction of flow near the hot wall, hence the recirculation cores become weak and effect on the buoyant force. The maximum value of the stream function can be noticed in case of nanofluid at (Ø=60), whereas they decrease when (Ø > 60), where the baffle obstruction causing decreases in flow movement. So that the left region temperature increases which cause reduction of the convective heat transfer by the inner fluid temperatures. This is an indication of enhancing of insulation. When the inclination angle increases (Ø >90), the baffle obstruction on flow and fluid resistance becomes smaller and the buoyancy strength increase, as a result, the heat transfer is increasing in this case. As a result of increasing the thermal conductivity from 1 to 10, an increase in the amount of heat transferred through the solid wall to the internal fluid have been noticed. This change can be seen in the isothermal lines, also, there was growth and an increase in the temperature gradient. The increasing of wall thickness from (D=0.1 to 0.4) leads to reduce the intensive heating through the solid wall as well as small heat transferred to the inner fluid. Therefore, it can be noticed that when the wall thickness increases the stream function decrease.

Numerical Analysis of Natural Convection Heat Transfer From a Vertical Hollow Cylinder Suspended in Air

2018 ◽  
Vol 140 (5) ◽  
Author(s):  
Swastik Acharya ◽  
Sumit Agrawal ◽  
Sukanta K. Dash
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Natural Convection ◽  
Rayleigh Number ◽  
Hollow Cylinder ◽  
Outer Surface ◽  
Average Nusselt Number ◽  
Convection Heat Transfer ◽  
Natural Convection Heat Transfer ◽  
Convection Heat

Natural convection heat transfer from a vertical hollow cylinder suspended in air has been analyzed numerically by varying the Rayleigh number (Ra) in the laminar (104 ≤ Ra ≤ 108) regime. The simulations have been carried out by changing the ratio of length to pipe diameter (L/D) in the range of 0.05 ≤ L/D≤20. Full conservation equations have been solved numerically for a vertical hollow cylinder suspended in air using algebraic multigrid solver of fluent 13.0. The flow and the temperature field around the vertical hollow cylinder have been observed through velocity vectors and temperature contours for small and large L/D. It has been found that the average Nusselt number (Nu) for vertical hollow cylinder suspended in air increases with the increase in Rayleigh number (Ra) and the Nu for both the inner and the outer surface also increases with Ra. However, with the increase in L/D, average Nu for the outer surface increases almost linearly, whereas the average Nu for the inner surface decreases and attains asymptotic value at higher L/D for low Ra. In this study, the effect of parameters like L/D and Ra on Nu is analyzed, and a correlation for average Nusselt number has been developed for the laminar regime. These correlations are accurate to the level of ±6%.

Free Convection Heat Transfer Across Inclined Honeycomb Panels

1977 ◽  
Vol 99 (1) ◽  
pp. 86-91 ◽  
Author(s):  
R. L. D. Cane ◽  
K. G. T. Hollands ◽  
G. D. Raithby ◽  
T. E. Unny
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Free Convection ◽  
Convection Heat Transfer ◽  
Correlation Equation ◽  
Base Flow ◽  
Convection Heat ◽  
Radiative Coupling ◽  
Aspect Ratios ◽  
Free Convection Heat

Experimentally obtained Nusselt number-Rayleigh number plots are presented for free convective heat transfer across honeycomb panels, heated from below, and inclined with respect to the horizontal at angles of 0, 30, 45, 60, and 90 deg. Aspect ratios of honeycomb cells of 2, 3, 4, and 5 are included; the fluid contained in the cells is air. Substantial suppression of free convection is observed when compared with an air layer of the same depth but not containing a honeycomb. Heat transfer associated with the base flow is found to be of only moderate importance at angles near horizontal, but of considerable consequence for angles near the vertical. The honeycomb walls used were partly transparent to thermal radiation, and a strong radiative coupling is indicated. A correlation equation for the Nusselt number, valid over part of the experimental range, is presented.

Sign in / Sign up

Export Citation Format

Share Document