scholarly journals Analysis of a severe beyond design basis accident for the EGP-6 reactor of the Bilibino NPP. Radioactive source term determination

2018 ◽  
Vol 4 (2) ◽  
pp. 135-142
Author(s):  
Ruben Mukhamadeev ◽  
Leonid Parafilo ◽  
Yury Baranaev ◽  
Albert Suvorov
Keyword(s):  
Experimental Data ◽  
Source Term ◽  
Fission Products ◽  
Severe Accident ◽  
Water Mixture ◽  
Design Basis ◽  
Short Period ◽  
Design Basis Accident ◽  
Fuel Material ◽  
Graphite Stack

Analysis was performed of dynamic phase of severe accident of the EGP-6 reactor of the Bilibino NPP, due to uncontrolled reactivity insertion initiated by withdrawal of two pare of automatic control rods with followed by full failure of reactor emergency protection system. This initial event leads to promt increasing of reactor core power up to 450% of nominal value with short period, coupled with rise of temperature of fuel, pressure and temperature of coolant. These factors lead to crisis of heat exchange with subsequent ruptures tubes of fuel assemblies and coolant blow down into graphite stack. All its lead to rise of pressure in reactor shell and damage of it, outflow of steam-water mixture through up-reactor area to ventilation system, communication corridors and reactor hall and further – to atmospheric release. Transient processes were calculated using code RELAP5/Mod3.2. It was considered stages of processes of fuel damage and evaluated dynamic of a number and degree of damaged fuel assembles. They were grouped on burn-up and for each group it was performed analysis of dynamic of damage values. Further it was considered processes of yield of fission products from damaged fuel with models, based on experimental data on yield of fission products from fuel material, used in assembles of Bilibino NPP fuel type (fuel tubes with steel cladding, where fuel material is grits of uranium dioxide in magnesium), under condition of severe accident, especially performed in SSC IPPE. Transport of fission products with steam and air up to release points was evaluated with models, based on experimental data of fission product transport through graphite stack under conditions of severe accident, also especially performed in SSC IPPE. Evaluation of source term was performed in accordance with accident dynamic and assumed modes of release for conservative and most possible approaches. It was noted good self-protection property of EGP-6 reactor under severe beyond design basis accident condition.

scholarly journals Analysis of a severe beyond design basis accident for the EGP-6 reactor facility at Bilibino NPP. Release source term formation

2018 ◽  
Vol 2018 (1) ◽  
pp. 99-111 ◽  
Author(s):  
Leonid Mikhailovich Parafilo ◽  
Ruben Ildarovich Mukhamadeev ◽  
Yury Dmitrievich Baranaev ◽  
Albert Petrovich Suvorov
Keyword(s):  
Source Term ◽  
Reactor Facility ◽  
Design Basis ◽  
Design Basis Accident

Modeling of Thermal Hydraulics Features of Top Water Reflood Experiment PARAMETER-SF3 Using SOCRAT/V2 Code

2009 ◽  
Author(s):  
Arcadii E. Kisselev ◽  
Valerii F. Strizhov ◽  
Alexander D. Vasiliev ◽  
Vladimir I. Nalivayev ◽  
Nikolay Ya. Parshin
Keyword(s):  
Experimental Data ◽  
Nuclear Power ◽  
Cooling System ◽  
Severe Accident ◽  
Numerical Code ◽  
Thermal Hydraulics ◽  
Vver Fuel ◽  
Design Basis ◽  
Best Estimate ◽  
Core Cooling

The PARAMETER-SF3 test conditions simulated a severe LOCA (Loss of Coolant Accident) nuclear power plant sequence in which the overheated up to 1700÷2300K core would be reflooded from the top and the bottom in occasion of ECCS (Emergency Core Cooling System) recovery. The test was successfully conducted at the NPO “LUTCH”, Podolsk, Russia, in October 31, 2008, and was the third of four experiments of series PARAMETER-SF. PARAMETER facility of NPO “LUTCH”, Podolsk, is designed for studies of the VVER fuel assemblies behavior under conditions simulating design basis, beyond design basis and severe accidents. The test bundle was made up of 19 fuel rod simulators with a length of approximately 3.12 m (heated rod simulators) and 2.92 m (unheated rod simulator). Heating was carried out electrically using 4-mm-diameter tantalum heating elements installed in the center of the rods and surrounded by annular UO2 pellets. The rod cladding was identical to that used in VVERs: Zr1%Nb, 9.13 mm outside diameter, 0.7 mm wall thickness. After the maximum cladding temperature of about 1900K was reached in the bundle during PARAMETER-SF3 test, the top flooding was initiated. The thermal hydraulic and SFD (Severe Fuel Damage) best estimate numerical complex SOCRAT/V2 was used for the calculation of PARAMETER-SF3 experiment. The counter-current flow limitation (CCFL) model was implemented to best estimate numerical code SOCRAT/V2 developed for modeling thermal hydraulics and severe accident phenomena in a reactor. Thermal hydraulics in PARAMETER-SF3 experiment played very important role and its adequate modeling is important for the thermal analysis. The results obtained by the complex SOCRAT/V2 were compared with experimental data concerning different aspects of thermal hydraulics behavior including the CCFL phenomenon during the reflood. The temperature experimental data were found to be in a good agreement with calculated results. It is indicative of the adequacy of modeling the complicated thermo-hydraulic behavior in the PARAMETER-SF3 test.

Validation of the Deterministic Realistic Method Applied to CATHARE on LB LOCA Experiments

2002 ◽  
Author(s):  
Jean-Yves Sauvage ◽  
Ste´phane Laroche
Keyword(s):  
Experimental Data ◽  
Statistical Analysis ◽  
Deterministic Model ◽  
Evaluation Model ◽  
Flexible Tool ◽  
Model Based ◽  
Design Basis ◽  
Best Estimate ◽  
Design Basis Accident

Framatome-ANP and EDF have defined a generic approach for using a best-estimate code in design basis accident studies called Deterministic Realistic Method (DRM). It has been applied to elaborate a LB LOCA ECCS evaluation model based on the CATHARE code. From a prior statistical analysis of uncertainties, the DRM derives a conservative deterministic model, preserving the realistic nature of the simulation, to be used in the further applications. The conservatism of the penalized model is demonstrated comparing penalized calculations with relevant experimental data. The DRM proved to be a highly flexible tool and has been applied successfully to meet the specific French and specific Belgian requirements of Safety Authorities.

Application of Thermal Hydraulic Code SOCRAT/V2 to Top Water Reflood Experiment PARAMETER-SF3

2009 ◽  
Author(s):  
Alexander D. Vasiliev
Keyword(s):  
Experimental Data ◽  
Nuclear Power ◽  
Cooling System ◽  
Severe Accident ◽  
Numerical Code ◽  
Thermal Hydraulics ◽  
Vver Fuel ◽  
Design Basis ◽  
Best Estimate ◽  
Core Cooling

The PARAMETER-SF3 test conditions simulated a severe LOCA (Loss of Coolant Accident) nuclear power plant sequence in which the overheated up to 1700–2300K core would be reflooded from the top and the bottom in occasion of ECCS (Emergency Core Cooling System) recovery. The test was successfully conducted at the NPO “LUTCH”, Podolsk, Russia, in October 31, 2008, and was the third of four experiments of series PARAMETER-SF. PARAMETER facility of NPO “LUTCH”, Podolsk, is designed for studies of the VVER fuel assemblies behavior under conditions simulating design basis, beyond design basis and severe accidents. The test bundle was made up of 19 fuel rod simulators with a length of approximately 3.12 m (heated rod simulators) and 2.92 m (unheated rod simulator). Heating was carried out electrically using 4-mm-diameter tantalum heating elements installed in the center of the rods and surrounded by annular UO2 pellets. The rod cladding was identical to that used in VVERs: Zr1%Nb, 9.13 mm outside diameter, 0.7 mm wall thickness. After the maximum cladding temperature of about 1900K was reached in the bundle during PARAMETER-SF3 test, the top flooding was initiated. The thermal hydraulic and SFD (Severe Fuel Damage) best estimate numerical complex SOCRAT/V2 was used for the calculation of PARAMETER-SF3 experiment. The counter-current flow limitation (CCFL) model was implemented to best estimate numerical code SOCRAT/V2 developed for modeling thermal hydraulics and severe accident phenomena in a reactor. Thermal hydraulics in PARAMETER-SF3 experiment played very important role and its adequate modeling is important for the thermal analysis. The results obtained by the complex SOCRAT/V2 were compared with experimental data concerning different aspects of thermal hydraulics behavior including the CCFL phenomenon during the reflood. The temperature experimental data were found to be in a good agreement with calculated results. It is indicative of the adequacy of modeling the complicated thermo-hydraulic behavior in the PARAMETER-SF3 test.

Accessibility Analysis for Staff After Accident of PWR Unit

2017 ◽  
Author(s):  
Ye Zhang ◽  
Xiaoxia Wang ◽  
Wei You ◽  
Zhuoran Li ◽  
Liying Zhang ◽  
...  
Keyword(s):  
Radioactive Material ◽  
Severe Accident ◽  
Accessibility Analysis ◽  
Dose Rates ◽  
Design Basis ◽  
Design Basis Accident

Severe accident has become one of the main directions of research since the crisis at Fukushima plants in Japan, including release of radioactive material, accessibility analysis for staff and evaluation of consequence. This paper, mainly for design basic accident and severe accident, makes calculation of migration and release of radioactive material after accident by considering the different building, also combine the on-site operation requirement of worker after accident, analyzes dose rates of typical zone for staff and evaluate the exposure caused by radioactive material. The main results of the paper supply reference and basis for person accessibility research after design basis accident and severe accident.

IRSN R&D Actions on FP Behaviour for RCS, Containment and FCVS in Severe Accident Conditions

2016 ◽  
Author(s):  
Laurent Cantrel ◽  
Thierry Albiol ◽  
Loïc Bosland ◽  
Juliette Colombani ◽  
Frédéric Cousin ◽  
...  
Keyword(s):  
Porous Materials ◽  
Nuclear Power ◽  
Source Term ◽  
Cooling System ◽  
Fission Products ◽  
Simulation Software ◽  
Severe Accident ◽  
Status Report ◽  
Diagnosis And Prognosis ◽  
Accident Conditions

This paper deals with near past, ongoing and planned R&D works on fission products (FPs) behaviour in Reactor Cooling System (RCS), containment building and in Filtered Containment Venting Systems (FCVS) for severe accident (SA) conditions. For the last topic, in link with the Fukushima post-accident management and possible improvement of mitigation actions for such SA, the FCVS topic is again on the agenda (see Status Report on Filtered Containment Venting, OECD/NEA/CSNI, Report NEA/CSNI/R(2014)7, 2014.) with a large interest at the international scale. All the researches are collaborative works; the overall objective is to develop confident models to be implemented in ASTEC SA simulation software. After being initiated in the International Source Term Program (ISTP), researches devoted to the understanding of iodine transport through the RCS are still ongoing in the frame of a bilateral agreement between IRSN and EDF with promising results. In 2017, a synthesis report of the last 10 years of researches, which have combined experimental and fundamental works based on the use of theoretical chemistry tools, will be issued. For containment, the last advances are linked to the Source Term Evaluation and Mitigation (STEM) OECD/NEA project operated by IRSN. The objective of the STEM project was to improve the evaluation of Source Term (ST) for a SA on a nuclear power plant and to reduce uncertainties on specific phenomena dealing with the chemistry of two major fission products: iodine and ruthenium. More precisely, the STEM project provided additional knowledge and improvements for calculation tools in order to allow a more robust diagnosis and prognosis of radioactive releases in a SA. STEM data will be completed by a follow-up, called STEM2, to further the knowledge concerning some remaining issues and be closer to reactor conditions. Two additional programmes deal with FCVS issues: the MItigation of outside Releases in the Environment (MIRE) (2013–2019) French National Research Agency (NRA) programme and the Passive and Active Systems on Severe Accident source term Mitigation (PASSAM) (2013–2016) European project. For FCVS works, the efficiencies for trapping iodine with various FCVS, covering scrubbers and dry filters, are examined to get a clear view of their abilities in SA conditions. Another part, performed in collaboration with French universities (Lorraine and Lille 1), is focused on the enhancement of the performance of these filters with specific porous materials able to trap volatile iodine. For that, influence of zeolites materials parameters (nature of the counter-ions, structure, Si/Al ratio …) will be tested. New kind of porous materials constituted by Metal organic Frameworks (MOF) will also be looked at because they can constitute a promising way of trapping.

scholarly journals Source Term Derivation and Radioactive Release Evaluation for JRTR Research Reactor under Severe Accident

2020 ◽  
Vol 2020 ◽  
pp. 1-9 ◽  
Author(s):  
Ned Xoubi
Keyword(s):  
Research Reactor ◽  
Source Term ◽  
Atmospheric Dispersion ◽  
Reactor Core ◽  
Fission Products ◽  
Severe Accident ◽  
Safety Standards ◽  
Gaussian Plume ◽  
Public Exposure ◽  
Radioactive Release

The source term for the JRTR research reactor is derived under an assumed hypothetical severe accident resulting in generation of the most severe consequences. The reactor core is modeled based on the reactor technical design specifications, and the fission products inventory is calculated by using the SCALE/TRITON depletion sequence to perform burnup and decay analyses via coupling the NEWT 2-D transport lattice code to the ORIGEN-S fuel depletion code. Fifty radioisotopes contributed to the evaluation, resulting in a source term of 3.7 × 1014 Bq. Atmospheric dispersion was evaluated using the Gaussian plume model via the HOTSPOT code. The plume centerline total effective dose (TED) was found to exceed the IAEA limits for occupational exposure of 0.02 Sv; the results showed that the maximum dose is 200 Sv within 200 m from the reactor, under all the weather stability classes, after which it starts to decrease with distance, reaching 0.1 Sv at 1 km from the reactor. The radiation dose plume centerlines continue to the exceed international basic safety standards annual limit of 1 mSv for public exposure, up to 80 km from the reactor.

scholarly journals Results of Structural Analysis of WWER-1000/320 Containment Behavior under Severe Accidents

2020 ◽  
pp. 18-30
Author(s):  
L. Liashenko ◽  
A. Panchenko ◽  
O. Shugailo ◽  
M. Koliada
Keyword(s):  
Strain State ◽  
Cylindrical Part ◽  
Severe Accident ◽  
Normal Operation ◽  
Stress And Strain ◽  
Severe Accidents ◽  
Design Basis ◽  
Calculation Results ◽  
Design Basis Accident ◽  
Maximum Design

The paper presents the review and evaluation of the containment prestressing system within reinforced concrete structures under seismic loads and severe accidents. Given the complex design of the containment, the detailed finite element model has been developed and used to describe real containment behavior. Containment stress and strain state was calculated by modern LIRA software. The first stage analyzed the results of WWER-1000/320 containment stress and strain state calculation under a combination of loads caused by maximum design basis accident (MDBA) and safe shutdown earthquake (SSE) and defined minimum acceptable tension of tendons. The research determines the minimum acceptable tension of tendons in the containment prestressing system, and evaluates the strength and reliability of containment structures under a combination of loads in normal operation + design-basis accident + maximum design earthquake (NO + DBA + MDE). The verification calculations have been performed using tendon tension of 780 ton-force in the cylindrical part of the containment and 760 ton-force in the containment dome. The second stage covered the analysis of severe accident parameters (pressure and temperature) and the results of calculation. Stress and strain state in ZNPP-1 containment has been calculated, parameters (pressure and temperature) under which the containment can loss its protective and isolation functions have been identified, calculation results have been analysed and conclusions of containment structural integrity and ensuring the implementation of the design confining functions have been made. Based on the calculation results, it can be concluded that strength of the containment cylindrical part during a beyond design-basis accident cannot be ensured under parameters t (temperature) = 120°С, p (pressure) = 0.6 MPa.

Assessment of the Dynamic Loads Applied to the RBMK-1000 Subreactor Room Walls and Slab during Vapor Explosion

Vestnik MEI ◽  
2021 ◽  
Vol 2 (2) ◽  
pp. 29-36
Author(s):  
Aleksey M. Osipov ◽  
◽  
Aleksandr V. Ryabov ◽  
Darya V. Finoshkina ◽  
◽  
...  
Keyword(s):  
Nuclear Power ◽  
Heat Removal ◽  
Severe Accident ◽  
Vapor Explosion ◽  
Metal Structures ◽  
Operating Modes ◽  
Design Basis ◽  
Design Basis Accident ◽  
Development Plans ◽  
Reactor Space

One of the conditions for the safe operation of a nuclear power plant (NPP) unit is a comprehensive design and experimental justification of its failure-free operation in all operating modes and limitation of accident radiation consequences, including those in the case of severe beyond design basis accidents. According to the nuclear power industry development plans in Russia, new NPPs equipped with RBMK-1000 reactors are not supposed to be constructed in the future. Although the assigned service life of RBMK-1000 based power units that remain in operation is close to expiration, these power units account for most of the electricity generation in the total amount of nuclear power capacities in Russia (about 40%); therefore, the relevant industry organizations have decided to extend their operation. This article analyzes the severe accident evolvement scenario at an RBMK-based NPP during the stage of severe core damage, in the course of which fuel-containing masses collapse into the subreactor space filled with water. Once fuel-containing masses emerge in the sub-reactor room, they come in interaction with the reactor base concrete. There is a potential danger of the concrete floor slab melting and the corium collapsing into the bubbler pool water. The main strategy foreseen for keeping the molten core within the reactor space boundaries involves decay heat removal from the reactor and cooling of the support metal structures by supplying water. However, the filling of the subreactor space with liquid may give rise to conditions under which vapor explosion can occur. The maximum dynamic impact applied to the RBMK-1000 subreactor room walls in the event of possible interaction between the molten corium and water during a severe beyond design basis accident is estimated. It is shown that when the corium melt interacts with a large amount of water in the subreactor room, the kinetic energy of the resulting water vapor is sufficient to cause significant destruction of the power unit building. When the water level in the subreactor room falls below one meter, the destruction hazard becomes less probable. The mass of hydrogen released as a result of the interaction is also estimated.

Evaluation of Iodine Source Term in PWR under Loss of Coolant Accident

2012 ◽  
Vol 482-484 ◽  
pp. 1115-1119 ◽  
Author(s):  
Khurram Mehboob ◽  
Xin Rong Cao
Keyword(s):  
Nuclear Power ◽  
Source Term ◽  
Fission Products ◽  
Retention Factor ◽  
Severe Accident ◽  
Loss Of Coolant Accident ◽  
Loss Of Coolant ◽  
Term Evaluation ◽  
Computer Based ◽  
Instantaneous Release

During the severe accident in nuclear power plant (NPP), large amounts of fission products are released with accident progression, including In-vessel and Ex-vessel release. Thus, the Source term evaluation is essential for the probability risk assessment (PRA) and is still imperative for the licensing and operation of NPPs. Iodine is one of the most reactive fission products emitting in a large amount to containment and have a severe impact on health and sounding environment. Therefore, the iodine source term has been evaluated for 1000MW Reactor, by considering the TMI-2 as the reference reactor. The modeling and simulation of released radioactivity have been carried out by developing a MATLAB computer-based program. For post 1100 operation days, with the instantaneous release of radioactivity to the containment has been studied under LOCA. The dependency of radioiodine on ventilation exhaust rates has been studied in normal, emergency and isolation mode of containment. Moreover, the containment retention factor is also evaluated in said states of containment.

Sign in / Sign up

Export Citation Format

Share Document