Determination of the Amplitude Values with Nakamura (H/V) Method and Standard Spectral Ratio (Ssr) Method at Ktu Campus

Author(s):  
Y.B. Beker ◽  
N. Sayil ◽  
Ö. Akin
Geosciences ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 186
Author(s):  
Alessandro Todrani ◽  
Giovanna Cultrera

On 24 August 2016, a Mw 6.0 earthquake started a damaging seismic sequence in central Italy. The historical center of Amatrice village reached the XI degree (MCS scale) but the high vulnerability alone could not explain the heavy damage. Unfortunately, at the time of the earthquake only AMT station, 200 m away from the downtown, recorded the mainshock, whereas tens of temporary stations were installed afterwards. We propose a method to simulate the ground motion affecting Amatrice, using the FFT amplitude recorded at AMT, which has been modified by the standard spectral ratio (SSR) computed at 14 seismic stations in downtown. We tested the procedure by comparing simulations and recordings of two later mainshocks (Mw 5.9 and Mw 6.5), underlining advantages and limits of the technique. The strong motion variability of simulations was related to the proximity of the seismic source, accounted for by the ground motion at AMT, and to the peculiar site effects, described by the transfer function at the sites. The largest amplification characterized the stations close to the NE hill edge and produced simulated values of intensity measures clearly above one standard deviation of the GMM expected for Italy, up to 1.6 g for PGA.


2006 ◽  
Vol 22 (1) ◽  
pp. 169-188 ◽  
Author(s):  
Sheri Molnar ◽  
John F. Cassidy

The applicability of the microtremor spectral ratio method is examined by comparing microtremor and weak-motion earthquake site responses at seven permanent strong-motion sites in Victoria, British Columbia. For each site, a weak-motion earthquake standard spectral ratio (bedrock reference), the average horizontal-to-vertical spectral ratio of up to five weak-motion earthquakes, and the average microtremor (Nakamura method) spectral ratio are compared. The geologic setting of Victoria is ideal for site response studies with a near-surface high impedance contrast between thin geologic layers of Victoria clay (about 11 m maximum in this study) and Pleistocene till or bedrock. Regardless of excitation source (weak-motion earthquakes or microtremors) and spectral ratio method, similar peak amplitudes and fundamental frequencies were found. Thicker material (>10 m) sites displayed higher peak amplitudes (up to six times amplification) at frequencies of 2–5 Hz compared to sites with a thin lens of material (<3 m) over bedrock that showed peak amplitudes at frequencies of >8 Hz.


1998 ◽  
Vol 14 (1) ◽  
pp. 203-224 ◽  
Author(s):  
D. Raptakis ◽  
N. Theodulidis ◽  
K. Pitilakis

In this study, the standard spectral ratio and the horizontal-to-vertical spectral ratio techniques are applied in order to study their effectiveness in investigating and quantifying the influence of geological conditions on strong ground motion. For this purpose, an accelerogram data set recorded at the Euroseistest array in the Mygdonia graben (lake Volvi area) near Thessaloniki, Greece, during the period April 1994 to June 1996 is used. Both experimental techniques show similar spectral ratio shapes with comparable fundamental resonant frequencies, which are well correlated with the well known geotechnical-geological conditions. Namely, the resonant frequency at the center of the valley is shifted to lower values, less than 1 Hz, while at the edge it is shifted to higher values, greater than 2 Hz. The horizontal-to-vertical spectral ratio technique is an effective method to estimate some basic characteristics of local site effects using a single accelerograph station. It reveals the fundamental resonant frequency of alluvial deposits by using only a single strong motion station, while the absolute level of the horizontal-to-vertical spectral ratio method tends to underestimate the amplification level compared to the standard spectral ratio technique.


2020 ◽  
Vol 222 (3) ◽  
pp. 2053-2067 ◽  
Author(s):  
Giovanni Lanzano ◽  
Chiara Felicetta ◽  
Francesca Pacor ◽  
Daniele Spallarossa ◽  
Paola Traversa

SUMMARY To evaluate the site response using both empirical approaches (e.g. standard spectral ratio, ground motion models (GMMs), generalized inversion techniques, etc.) and numerical 1-D/2-D analyses, the definition of the reference motion, that is the ground motion recorded at stations unaffected by site-effects due to topographic, stratigraphic or basin effects, is needed. The main objective of this work is to define a robust strategy to identify the seismic stations that can be considered as reference rock sites, using six proxies for the site response: three proxies are related to the analysis of geophysical and seismological data (the repeatable site term from the residual analysis, the resonance frequencies from horizontal-to-vertical spectral ratios on noise or earthquake signals, the average shear wave velocity in the first 30 m); the remaining ones concern geomorphological and installation features (outcropping rocks or stiff soils, flat topography and absence of interaction with structures). We introduce a weighting scheme to take into account the availability and the quality of the site information, as well as the fulfillment of the criterion associated to each proxy. We also introduce a hierarchical index, to take into account the relevance of the proposed proxies in the description of the site effects, and an acceptance threshold for reference rock sites identification. The procedure is applied on a very large data set, composed by accelerometric and velocimetric waveforms, recorded in Central Italy in the period 2008–2018. This data set is composed by more than 30 000 waveforms relative to 450 earthquakes in the magnitude range 3.2–6.5 and recorded by more than 450 stations. A total of 36 out of 133 candidate stations are identified as reference sites: the majority of them are installed on rock with flat topography, but this condition is not sufficient to guarantee the absence of amplifications, especially at high frequencies. Seismological analyses are necessary to exclude stations affected by resonances. We test the impact of using these sites by calibrating a GMMs. The results show that for reference rock sites the median predictions are reduced down to about 45 per cent at short periods in comparison to the generic rock motions.


Sign in / Sign up

Export Citation Format

Share Document