Assessment of CO2 Plume Geothermal (CPG) Systems

2018 ◽  
Author(s):  
S. Glos ◽  
M. Langer ◽  
M. Wechsung
Keyword(s):  
Co2 Plume

Effect of geological heterogeneities on reservoir storage capacity and migration of CO2 plume in a deep saline fractured carbonate aquifer

2021 ◽  
Vol 108 ◽  
pp. 103306
Author(s):  
M. Adeel Sohal ◽  
Yann Le Gallo ◽  
Pascal Audigane ◽  
J. Carlos de Dios ◽  
Sean P. Rigby
Keyword(s):  
Storage Capacity ◽  
Carbonate Aquifer ◽  
Reservoir Storage ◽  
Fractured Carbonate ◽  
Co2 Plume ◽  
And Migration

scholarly journals Numerical Simulation and Optimization of CO2 Sequestration in Saline Aquifers

2012 ◽  
Author(s):  
Zheming Zhang ◽  
Ramesh Agarwal
Keyword(s):  
Numerical Simulation ◽  
Co2 Sequestration ◽  
Storage Capacity ◽  
Co2 Storage ◽  
Injection Well ◽  
Co2 Injection ◽  
Great Promise ◽  
Saline Aquifer ◽  
Simulation And Optimization ◽  
Co2 Plume

With recent concerns on CO2 emissions from coal fired electricity generation plants; there has been major emphasis on the development of safe and economical Carbon Dioxide Capture and Sequestration (CCS) technology worldwide. Saline reservoirs are attractive geological sites for CO2 sequestration because of their huge capacity for sequestration. Over the last decade, numerical simulation codes have been developed in U.S, Europe and Japan to determine a priori the CO2 storage capacity of a saline aquifer and provide risk assessment with reasonable confidence before the actual deployment of CO2 sequestration can proceed with enormous investment. In U.S, TOUGH2 numerical simulator has been widely used for this purpose. However at present it does not have the capability to determine optimal parameters such as injection rate, injection pressure, injection depth for vertical and horizontal wells etc. for optimization of the CO2 storage capacity and for minimizing the leakage potential by confining the plume migration. This paper describes the development of a “Genetic Algorithm (GA)” based optimizer for TOUGH2 that can be used by the industry with good confidence to optimize the CO2 storage capacity in a saline aquifer of interest. This new code including the TOUGH2 and the GA optimizer is designated as “GATOUGH2”. It has been validated by conducting simulations of three widely used benchmark problems by the CCS researchers worldwide: (a) Study of CO2 plume evolution and leakage through an abandoned well, (b) Study of enhanced CH4 recovery in combination with CO2 storage in depleted gas reservoirs, and (c) Study of CO2 injection into a heterogeneous geological formation. Our results of these simulations are in excellent agreement with those of other researchers obtained with different codes. The validated code has been employed to optimize the proposed water-alternating-gas (WAG) injection scheme for (a) a vertical CO2 injection well and (b) a horizontal CO2 injection well, for optimizing the CO2 sequestration capacity of an aquifer. These optimized calculations are compared with the brute force nearly optimized results obtained by performing a large number of calculations. These comparisons demonstrate the significant efficiency and accuracy of GATOUGH2 as an optimizer for TOUGH2. This capability holds a great promise in studying a host of other problems in CO2 sequestration such as how to optimally accelerate the capillary trapping, accelerate the dissolution of CO2 in water or brine, and immobilize the CO2 plume.

CO2-plume geothermal in fluvial formations: A 2D numerical performance study using subsurface metrics and upscaling

Geothermics ◽  
2022 ◽  
Vol 99 ◽  
pp. 102287
Author(s):  
Amir Mohammad Norouzi ◽  
Jon Gluyas ◽  
Masoud Babaei
Keyword(s):  
Performance Study ◽  
Numerical Performance ◽  
Co2 Plume

Robust CO2 Plume Imaging Using Joint Tomographic Inversion Of Distributed Pressure And Temperature Measurements

2021 ◽  
Author(s):  
Changqing Yao ◽  
Hongquan Chen ◽  
Akhil Datta-Gupta ◽  
Sanjay Mawalkar ◽  
Srikanta Mishra ◽  
...  
Keyword(s):  
Carbon Sequestration ◽  
History Matching ◽  
Temperature Measurements ◽  
Injection Well ◽  
Co2 Injection ◽  
Pressure Data ◽  
Distributed Temperature Sensing ◽  
Data Set ◽  
Monitoring Well ◽  
Co2 Plume

Abstract Geologic CO2 sequestration and CO2 enhanced oil recovery (EOR) have received significant attention from the scientific community as a response to climate change from greenhouse gases. Safe and efficient management of a CO2 injection site requires spatio-temporal tracking of the CO2 plume in the reservoir during geologic sequestration. The goal of this paper is to develop robust modeling and monitoring technologies for imaging and visualization of the CO2 plume using routine pressure/temperature measurements. The streamline-based technology has proven to be effective and efficient for reconciling geologic models to various types of reservoir dynamic response. In this paper, we first extend the streamline-based data integration approach to incorporate distributed temperature sensor (DTS) data using the concept of thermal tracer travel time. Then, a hierarchical workflow composed of evolutionary and streamline methods is employed to jointly history match the DTS and pressure data. Finally, CO2 saturation and streamline maps are used to visualize the CO2 plume movement during the sequestration process. The power and utility of our approach are demonstrated using both synthetic and field applications. We first validate the streamline-based DTS data inversion using a synthetic example. Next, the hierarchical workflow is applied to a carbon sequestration project in a carbonate reef reservoir within the Northern Niagaran Pinnacle Reef Trend in Michigan, USA. The monitoring data set consists of distributed temperature sensing (DTS) data acquired at the injection well and a monitoring well, flowing bottom-hole pressure data at the injection well, and time-lapse pressure measurements at several locations along the monitoring well. The history matching results indicate that the CO2 movement is mostly restricted to the intended zones of injection which is consistent with an independent warmback analysis of the temperature data. The novelty of this work is the streamline-based history matching method for the DTS data and its field application to the Department of Engergy regional carbon sequestration project in Michigan.

Effect of brine salinity on CO2 plume migration and trapping capacity in deep saline aquifers

2017 ◽  
Vol 57 (1) ◽  
pp. 100 ◽  
Author(s):  
Emad A. Al-Khdheeawi ◽  
Stephanie Vialle ◽  
Ahmed Barifcani ◽  
Mohammad Sarmadivaleh ◽  
Stefan Iglauer
Keyword(s):  
Co2 Storage ◽  
Three Dimensional ◽  
Rock Properties ◽  
Saline Aquifers ◽  
Migration Distance ◽  
Deep Saline Aquifer ◽  
Plume Migration ◽  
Co2 Plume ◽  
Wet Rocks ◽  
Brine Salinity

CO2 migration and storage capacity are highly affected by various parameters (e.g. reservoir temperature, vertical to horizontal permeability ratio, cap rock properties, aquifer depth and the reservoir heterogeneity). One of these parameters, which has received little attention, is brine salinity. Although brine salinity has been well demonstrated previously as a factor affecting rock wettability (i.e. higher brine salinity leads to more CO2-wet rocks), its effect on the CO2 storage process has not been addressed effectively. Thus, we developed a three-dimensional homogeneous reservoir model to simulate the behaviour of a CO2 plume in a deep saline aquifer using five different salinities (ranging from 2000 to 200 000 ppm) and have predicted associated CO2 migration patterns and trapping capacities. CO2 was injected at a depth of 1408 m for a period of 1 year at a rate of 1 Mt year–1 and then stored for the next 100 years. The results clearly indicate that 100 years after the injection of CO2 has stopped, the salinity has a significant effect on the CO2 migration distance and the amount of mobile, residual and dissolved CO2. First, the results show that higher brine salinity leads to an increase in CO2 mobility and CO2 migration distance, but reduces the amount of residually trapped CO2. Furthermore, high brine salinity leads to reduced dissolution trapping. Thus, we conclude that less-saline aquifers are preferable CO2 sinks.

Simulation of CO2 plume movement in multilayered saline formations through multilayer injection technology in the Ordos Basin, China

2013 ◽  
Vol 71 (10) ◽  
pp. 4447-4462 ◽  
Author(s):  
Hejuan Liu ◽  
Zhengmeng Hou ◽  
Patrick Were ◽  
Yang Gou ◽  
Xiaoling Sun
Keyword(s):  
Ordos Basin ◽  
The Ordos Basin ◽  
Co2 Plume ◽  
Injection Technology

3D DAS-VSP Illumination Modeling for CO2 Plume Migration Monitoring in Offshore Sarawak, Malaysia

2021 ◽  
Author(s):  
Pankaj Kumar Tiwari ◽  
Zoann Low ◽  
Parimal Arjun Patil ◽  
Debasis Priyadarshan Das ◽  
Prasanna Chidambaram ◽  
...  
Keyword(s):  
Dynamic Simulation ◽  
Seismic Velocity ◽  
Time Lapse ◽  
Carbonate Reservoir ◽  
Fiber Optic Sensor ◽  
Co2 Injection ◽  
Storage Site ◽  
Plume Migration ◽  
Co2 Plume ◽  
4D Seismic

Abstract Monitoring of CO2 plume migration in a depleted carbonate reservoir is challenging and demand comprehensive and trailblazing monitoring technologies. 4D time-lapse seismic exhibits the migration of CO2 plume within geological storage but in the area affected by gas chimney due to poor signal-to-noise ratio (SNR), uncertainty in identifying and interpretation of CO2 plume gets exaggerated. High resolution 3D vertical seismic profile (VSP) survey using distributed acoustic sensor (DAS) technology fulfil the objective of obtaining the detailed subsurface image which include CO2 plume migration, reservoir architecture, sub-seismic faults and fracture networks as well as the caprock. Integration of quantitative geophysics and dynamic simulation with illumination modelling dignify the capabilities of 3D DAS-VSP for CO2 plume migration monitoring. The storage site has been studied in detailed and an integrated coupled dynamic simulation were performed and results were integrated with seismic forward modeling to demonstrate the CO2 plume migration with in reservoir and its impact on seismic amplitude. 3D VSP illumination modelling was carried out by integrating reservoir and overburden interpretations, acoustic logs and seismic velocity to illustrate the subsurface coverage area at top of reservoir. Several acquisition survey geometries were simulated based on different source carpet size for effective surface source contribution for subsurface illumination and results were analyzed to design the 3D VSP survey for early CO2 plume migration monitoring. The illumination simulation was integrated with dynamic simulation for fullfield CO2 plume migration monitoring with 3D DAS-VSP by incorporating Pseudo wells illumination analysis. Results of integrated coupled dynamic simulation and 4D seismic feasibility were analyzed for selection of best well location to deploy the multi fiber optic sensor system (M-FOSS) technology. Amplitude response of synthetic AVO (amplitude vs offsets) gathers at the top of carbonate reservoir were analyzed for near, mid and far angle stacks with respect to pre-production as well as pre-injection reservoir conditions. Observed promising results of distinguishable 25-30% of CO2 saturation in depleted reservoir from 4D time-lapse seismic envisage the application of 3D DAS-VSP acquisition. The source patch analysis of 3D VSP illumination modelling results indicate that a source carpet of 6km×6km would be cos-effectively sufficient to produce a maximum of approximately 2km in diameter subsurface illumination at the top of the reservoir. The Pseudo wells illumination analysis results show that current planned injection wells would probably able to monitor early CO2 injection but for the fullfield monitoring additional monitoring wells or a hybrid survey of VSP and surface seismic would be required. The integrated modeling approach ensures that 4D Seismic in subsurface CO2 plume monitoring is robust. Monitoring pressure build-ups from 3D DAS-VSP will reduce the associated risks.

Sign in / Sign up

Export Citation Format

Share Document