Effect of Temperature on Performance Parameters of Metallurgical Grade Polysilicon Solar Cells

2011 ◽  
Vol 148-149 ◽  
pp. 1252-1255 ◽  
Author(s):  
Li Fu Zhang ◽  
Yi Tan ◽  
Zhen Qiang Yang ◽  
Ze Fei Gao ◽  
Ying Nie
Keyword(s):  
Solar Cells ◽  
Open Circuit Voltage ◽  
Open Circuit ◽  
Effect Of Temperature ◽  
Stable Operation ◽  
Operating Voltage ◽  
Water Cooling ◽  
Quartic Equation ◽  
Metallurgical Silicon ◽  
The Relationship

By the stable operation of the experiments in actual outdoor conditions nearly a year, we find that the property of metallurgical silicon solar cells proves to be stable. The results show that the relationship between S-P could be expressed as a quartic equation. As the higher surface temperature of solar cells at noon on sunny day, both the open circuit voltage and the operating voltage are lower, the output power is reduced. It is concluded that the water cooling on the surface of the solar cells when the temperature T>50°C could improve power generation efficiency.

Microcrystalline (Si,Ge):H Solar Cells

2003 ◽  
Vol 762 ◽  
Author(s):  
Jianhua Zhu ◽  
Vikram L. Dalal
Keyword(s):  
Solar Cells ◽  
Buffer Layer ◽  
Quantum Efficiency ◽  
Fill Factor ◽  
Open Circuit Voltage ◽  
Defect Density ◽  
Cell Structure ◽  
Open Circuit ◽  
Base Layer ◽  
Ecr Plasma

AbstractWe report on the growth and properties of microcrystalline Si:H and (Si,Ge):H solar cells on stainless steel substrates. The solar cells were grown using a remote, low pressure ECR plasma system. In order to crystallize (Si,Ge), much higher hydrogen dilution (∼40:1) had to be used compared to the case for mc-Si:H, where a dilution of 10:1 was adequate for crystallization. The solar cell structure was of the p+nn+ type, with light entering the p+ layer. It was found that it was advantageous to use a thin a-Si:H buffer layer at the back of the cells in order to reduce shunt density and improve the performance of the cells. A graded gap buffer layer was used at the p+n interface so as to improve the open-circuit voltage and fill factor. The open circuit voltage and fill factor decreased as the Ge content increased. Quantum efficiency measurements indicated that the device was indeed microcrystalline and followed the absorption characteristics of crystalline ( Si,Ge). As the Ge content increased, quantum efficiency in the infrared increased. X-ray measurements of films indicated grain sizes of ∼ 10nm. EDAX measurements were used to measure the Ge content in the films and devices. Capacitance measurements at low frequencies ( ~100 Hz and 1 kHz) indicated that the base layer was indeed behaving as a crystalline material, with classical C(V) curves. The defect density varied between 1x1016 to 2x1017/cm3, with higher defects indicated as the Ge concentration increased.

Reducing recombination and enhancing open circuit voltage by Strontium-alloying in multiple cation perovskite solar cells

2017 ◽  
Author(s):  
Pietro Caprioglio ◽  
Fengshuo Zu ◽  
Christian M. Wolff ◽  
Martin Stolterfhot ◽  
Norbert Koch ◽  
...  
Keyword(s):  
Solar Cells ◽  
Open Circuit Voltage ◽  
Perovskite Solar Cells ◽  
Open Circuit

Monolithic perovskite silicon tandem solar cells with high-bandgap perovskite absorber exceeding 1.8 V open-circuit voltage

2019 ◽  
Author(s):  
Kristina M. Winkler ◽  
Ines Ketterer ◽  
Alexander J. Bett ◽  
Özde Kabakli ◽  
Martin Bivour ◽  
...  
Keyword(s):  
Solar Cells ◽  
Open Circuit Voltage ◽  
Open Circuit ◽  
Tandem Solar Cells

Importance of interfacial crystallinity to reduce open-circuit voltage loss in organic solar cells

2019 ◽  
Vol 115 (15) ◽  
pp. 153301 ◽  
Author(s):  
Seiichiro Izawa ◽  
Naoto Shintaku ◽  
Mitsuru Kikuchi ◽  
Masahiro Hiramoto
Keyword(s):  
Solar Cells ◽  
Organic Solar Cells ◽  
Open Circuit Voltage ◽  
Open Circuit ◽  
Voltage Loss

scholarly journals Subphthalocyanine‐Diketopyrrolopyrrole Conjugates: 3D Star‐Shaped Systems as Non‐Fullerene Acceptors in Polymer Solar Cells with High Open‐Circuit Voltage

ChemPlusChem ◽  
2021 ◽  
Author(s):  
Maria J. Álvaro‐Martins ◽  
José G. Sánchez ◽  
Giulia Lavarda ◽  
Desiré Molina ◽  
Josep Pallarès ◽  
...  
Keyword(s):  
Solar Cells ◽  
Open Circuit Voltage ◽  
Polymer Solar Cells ◽  
Open Circuit

scholarly journals Numerical Simulation Analysis of Ag Crystallite Effects on Interface of Front Metal and Silicon in the PERC Solar Cell

Energies ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 592
Author(s):  
Myeong Sang Jeong ◽  
Yonghwan Lee ◽  
Ka-Hyun Kim ◽  
Sungjin Choi ◽  
Min Gu Kang ◽  
...  
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
High Efficiency ◽  
Open Circuit Voltage ◽  
Surface Recombination ◽  
Open Circuit ◽  
Surface Recombination Velocity ◽  
Metal Interface ◽  
Ag Crystallites ◽  
Recombination Velocity

In the fabrication of crystalline silicon solar cells, the contact properties between the front metal electrode and silicon are one of the most important parameters for achieving high-efficiency, as it is an integral element in the formation of solar cell electrodes. This entails an increase in the surface recombination velocity and a drop in the open-circuit voltage of the solar cell; hence, controlling the recombination velocity at the metal-silicon interface becomes a critical factor in the process. In this study, the distribution of Ag crystallites formed on the silicon-metal interface, the surface recombination velocity in the silicon-metal interface and the resulting changes in the performance of the Passivated Emitter and Rear Contact (PERC) solar cells were analyzed by controlling the firing temperature. The Ag crystallite distribution gradually increased corresponding to a firing temperature increase from 850 ∘C to 950 ∘C. The surface recombination velocity at the silicon-metal interface increased from 353 to 599 cm/s and the open-circuit voltage of the PERC solar cell decreased from 659.7 to 647 mV. Technology Computer-Aided Design (TCAD) simulation was used for detailed analysis on the effect of the surface recombination velocity at the silicon-metal interface on the PERC solar cell performance. Simulations showed that the increase in the distribution of Ag crystallites and surface recombination velocity at the silicon-metal interface played an important role in the decrease of open-circuit voltage of the PERC solar cell at temperatures of 850–900 ∘C, whereas the damage caused by the emitter over fire was determined as the main cause of the voltage drop at 950 ∘C. These results are expected to serve as a steppingstone for further research on improvement in the silicon-metal interface properties of silicon-based solar cells and investigation on high-efficiency solar cells.

Sign in / Sign up

Export Citation Format

Share Document