Investigation on Surface Roughness and Cutting Temperature in Turning AISI 316 Austenitic Stainless Steel Using TiAlSiN Coated Carbide Insert

2013 ◽  
Vol 446-447 ◽  
pp. 291-295
Author(s):  
Malhar Ozarkar ◽  
Rugwed Bhatkhande ◽  
Shray Jerath ◽  
A.P. Kulkarni
Keyword(s):  
Surface Roughness ◽  
Cutting Speed ◽  
Experimental Result ◽  
Interface Temperature ◽  
Depth Of Cut ◽  
Aisi 316 ◽  
Coated Carbide ◽  
Coated Cemented Carbide ◽  
Carbide Insert ◽  
Tialsin Coating

This study presents experimental result of surface roughness and chip-tool interface temperature developed during turning of AISI 316 austenitic stainless steels using TiAlSiN coated cemented carbide insert. TiAlSiN coating is deposited by Cathodic Arc Evaporation (PVD) technique. The work-tool thermocouple calibration set-up was developed. The air heater was used as a heating element at the work-tool junction. The experiments were conducted at cutting speeds in the range of 140 to 320 m/min, feed in the range of 0.08 to 0.26 mm/rev keeping depth of cut constant at 1 mm. The influence of cutting parameters and tool coating were investigated on the average chip-tool interface temperature and surface roughness. Experimentally interface temperature 979°C was observed at 260 m/min cutting speed and 0.14 mm/rev feed. The interface temperature in turning is strongly dependent on the cutting speed followed by feed and exactly reverse case was observed in case of surface roughness. TiAlSiN coating shows better performance and can be considered as a prominent candidate for the machining of AISI 316 work material.

Effects of Insert Nose Radius and Processing Cutting Parameter on the Surface Roughness of Aisi 316 Stainless Steel

2010 ◽  
Vol 447-448 ◽  
pp. 51-54
Author(s):  
Mohd Fazuri Abdullah ◽  
Muhammad Ilman Hakimi Chua Abdullah ◽  
Abu Bakar Sulong ◽  
Jaharah A. Ghani
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Surface Finish ◽  
Feed Rate ◽  
Cutting Speed ◽  
Chip Thickness ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Nose Radius ◽  
Aisi 316

The effects of different cutting parameters, insert nose radius, cutting speed and feed rates on the surface quality of the stainless steel to be use in medical application. Stainless steel AISI 316 had been machined with three different nose radiuses (0.4 mm 0.8 mm, and 1.2mm), three different cutting speeds (100, 130, 170 m/min) and feed rates (0.1, 0.125, 0.16 mm/rev) while depth of cut keep constant at (0.4 mm). It is seen that the insert nose radius, feed rates, and cutting speed have different effect on the surface roughness. The minimum average surface roughness (0.225µm) has been measured using the nose radius insert (1.2 mm) at lowest feed rate (0.1 mm/rev). The highest surface roughness (1.838µm) has been measured with nose radius insert (0.4 mm) at highest feed rate (0.16 mm/rev). The analysis of ANOVA showed the cutting speed is not dominant in processing for the fine surface finish compared with feed rate and nose radius. Conclusion, surface roughness is decreasing with decreasing of the feed rate. High nose radius produce better surface finish than small nose radius because of the maximum uncut chip thickness decreases with increase of nose radius.

A Comprehensive Study on Surface Roughness in Machining of AISI D2 Hardened Steel

2012 ◽  
Vol 576 ◽  
pp. 60-63 ◽  
Author(s):  
N.A.H. Jasni ◽  
Mohd Amri Lajis
Keyword(s):  
Surface Roughness ◽  
High Speed ◽  
End Milling ◽  
Cutting Speed ◽  
Hardened Steel ◽  
Depth Of Cut ◽  
Feed Speed ◽  
Radial Depth ◽  
Aisi D2 ◽  
Coated Carbide

Hard milling of hardened steel has wide application in mould and die industries. However, milling induced surface finish has received little attention. An experimental investigation is conducted to comprehensively characterize the surface roughness of AISI D2 hardened steel (58-62 HRC) in end milling operation using TiAlN/AlCrN multilayer coated carbide. Surface roughness (Ra) was examined at different cutting speed (v) and radial depth of cut (dr) while the measurement was taken in feed speed, Vf and cutting speed, Vc directions. The experimental results show that the milled surface is anisotropic in nature. Surface roughness values in feed speed direction do not appear to correspond to any definite pattern in relation to cutting speed, while it increases with radial depth-of-cut within the range 0.13-0.24 µm. In cutting speed direction, surface roughness value decreases in the high speed range, while it increases in the high radial depth of cut. Radial depth of cut is the most influencing parameter in surface roughness followed by cutting speed.

Evaluation of Cutting Force and Surface Roughness in Turning of GFRP Using Coated Carbide Insert

2015 ◽  
Vol 813-814 ◽  
pp. 317-321 ◽  
Author(s):  
C. Ramesh Kannan ◽  
P. Padmanabhan ◽  
K.P. Vasanthakumar
Keyword(s):  
Surface Roughness ◽  
Glass Fiber ◽  
Cutting Force ◽  
Chemical Vapour ◽  
Deposition Process ◽  
Depth Of Cut ◽  
Reinforced Plastics ◽  
Coated Carbide ◽  
Machining Parameter ◽  
Carbide Insert

This paper is to evaluate the cutting force and surface roughness in turning of Glass fiber reinforced plastics (E-glass fiber) using coated carbide insert. The comparison of the results with uncoated carbide inserts. The carbide insert is coated by multilayer chemical vapour deposition process, the coating elements are TiN/Al2O3/TiCN. The experiment is carried out in the conventional lathe machine under dry condition by varying the three cutting parameter such as speed, feed and depth of cut. The cutting force is measured using a lathe tool dynamometer and surface roughness are measured by using surf tester.The result of the experiment shows the effect of machining parameter on cutting force and surface roughness. The results have confirmed that the coated carbide insert has better results than uncoated and tool life is increased.

The Effects of Cutting Parameters on Work-Hardening of Milling Invar 36

2015 ◽  
Vol 1089 ◽  
pp. 373-376
Author(s):  
Xing Wei Zheng ◽  
Guo Fu Ying ◽  
Yan Chen ◽  
Yu Can Fu
Keyword(s):  
Work Hardening ◽  
Lattice Distortion ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Metallographic Structure ◽  
Metallographic Observation ◽  
Coated Carbide ◽  
Carbide Insert ◽  
Axial Depth

An experiment of face milling of Invar36 was conducted by using coated carbide insert, the microhardness was tested and the metallographic structure was observed to figure out the principles of work-hardening. The results showed that the depth of work-hardening ranges from 80μm to 160μm among the parameters selected in the experiments. The degree and the depth of work-hardening were significantly affected by the axial depth of cut and feed per tooth. The degree and the depth of work-hardening showed a tendency to increase with the increase of the axial depth of cut and feed per tooth. Compared with the axial depth of cut and feed per tooth, cutting speed had less influence on the degree and depth of work-hardening. The degree and depth of work- hardening decreased slowly with the increase of cutting speed. Metallographic observation showed that work-hardening layer consisted of the thermal force influenced layer and the force influenced layer, while the amorphous metallographic structure was observed in the thermal force influenced layer, and lattice distortion was observed in the force influenced layer.

Cutting Forces and Surface Roughness in High-Speed End Milling of Ti6Al4V

2013 ◽  
Vol 589-590 ◽  
pp. 76-81
Author(s):  
Fu Zeng Wang ◽  
Jun Zhao ◽  
An Hai Li ◽  
Jia Bang Zhao
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Cutting Forces ◽  
High Speed ◽  
End Milling ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Wide Range ◽  
Radial Depth ◽  
Coated Carbide

In this paper, high speed milling experiments on Ti6Al4V were conducted with coated carbide inserts under a wide range of cutting conditions. The effects of cutting speed, feed rate and radial depth of cut on the cutting forces, chip morphologies as well as surface roughness were investigated. The results indicated that the cutting speed 200m/min could be considered as a critical value at which both relatively low cutting forces and good surface quality can be obtained at the same time. When the cutting speed exceeds 200m/min, the cutting forces increase rapidly and the surface quality degrades. There exist obvious correlations between cutting forces and surface roughness.

Modeling & Optimization of Surface Roughness & Vibration Amplitude in Heat Assisted End Milling of SKD 11 Tool Steel Using Ball Nose Tool

2012 ◽  
Vol 538-541 ◽  
pp. 799-803 ◽  
Author(s):  
A.K.M. Nurul Amin ◽  
Muhd Hafiz B. Md. Saad ◽  
Muammer Din Arif
Keyword(s):  
Surface Roughness ◽  
Response Surface ◽  
Tool Steel ◽  
Vibration Amplitude ◽  
End Milling ◽  
Heating Temperature ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Primary Input ◽  
Coated Carbide

Tool steel - SKD 11 is frequently used in industries for making dies and molds. This grade is chosen for its toughness, strength, and hardness maintained up to high temperature. However, the same properties make the steel extremely difficult and expensive to machine using conventional approaches. Heat assisted machining has been found wide spread application in recent years to improve machinability of difficult-to-cut materials. This research paper presents the outcome of an investigation on heat assisted end milling of SKD 11 conducted on a vertical machining center using ball nose coated carbide inserts. The Design of Experiments (DoE) was done using the Response Surface Methodology, in order to develop empirical mathematical models of surface roughness and vibration in terms of cutting speed, feed, axial depth of cut, and heating temperature. The models were checked for significance using Analysis of Variance (ANOVA). 3-D response surface graphs of the interactions of primary cutting parameters with the responses were plotted. Optimization was then performed by using the desirability function approach. From the graphs and optimized results it was concluded that the primary input parameters could be controlled in order to reduce vibration amplitude and produce semi-finished machined surfaces applying induction heat assisted technique.

scholarly journals Optimisation of the Machining of Stellite 6 PTA Hardfacing Using Surface Roughness

2010 ◽  
Vol 443 ◽  
pp. 227-231 ◽  
Author(s):  
Md Shahanur Hasan ◽  
Md Mazid Abdul ◽  
Richard E. Clegg
Keyword(s):  
Surface Roughness ◽  
Cutting Speed ◽  
Deposition Process ◽  
Depth Of Cut ◽  
High Corrosion Resistance ◽  
Turning Operations ◽  
Stellite 6 ◽  
Cutting Regimes ◽  
Coated Carbide ◽  
Carbide Inserts

Stellites are cobalt based super alloys. By virtue of their excellent physio-mechanical properties, stellites are highly regarded engineering materials. Stellites posses high corrosion resistance and wear resistance properties. This study investigates the Stellite deposition process and machinability of Stellite 6 deposited on steel subtrate. Stellite 6 was deposited onto a 4140 bar using a plasma transfer arc (PTA) system and machinability was assessed on the basis of surface roughness. A series of turning operations have been carried out on a conventional lathe using coated carbide inserts and surface roughness was evaluated by Stylus type Surtronic3+ instrument. The values of surface roughness were plotted against different cutting speed, feed rate and depth of cut to display the results in graphical forms. Optimal cutting regimes were established against the best values of surface roughness.

Investigation of Chip and Surface Roughness when Milling AISI304 Stainless Steel

2017 ◽  
Vol 889 ◽  
pp. 152-158
Author(s):  
K. Kadirgama ◽  
K. Abou-El-Hossein
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Feed Rate ◽  
Prediction Models ◽  
Cutting Speed ◽  
Experimental Result ◽  
Quadratic Model ◽  
Depth Of Cut ◽  
Cutting Condition ◽  
Axial Depth

Stainless steel was used for many engineering applications. The optimum parameters needs to be identify to save the cutting tool usage and increase productivity. The purpose of this study is to develop the surface roughness mathematical model for AISI 304 stainless steel when milling using TiN (CVD) carbide tool. The milling process was done under various cutting condition which is cutting speed (1500, 2000 and 2500 rpm), feed rate (0.02, 0.03 and 0.04 mm/tooth) and axial depth (0.1, 0.2 and 0.3 mm). The first order model and quadratic model have been developed using Response Surface Method (RSM) with confident level 95%. The prediction models were comparing with the actual experimental results. It is found that quadratic model much fit the experimental result compare to linear model. In general, the results obtained from the mathematical models were in good agreement with those obtained from the machining experiments. Besides that, it is shown that the influence of cutting speed and feed rate are much higher on surface roughness compare to depth of cut. The optimum cutting speed, feed rate and axial depth is 2500 rpm, 0.0212 mm/tooth and 0.3mm respectively. Besides that, continues chip is produced at cutting speed 2500 rpm meanwhile discontinues chip produced at cutting speed 1500 rpm.

Modelling and Optimization of Tool Chip Interface Temperature and Surface Roughness in CNC Dry Turning of EN 24 Steel

2016 ◽  
Vol 16 ◽  
pp. 7-15 ◽  
Author(s):  
Nirmal Kumar Mandal ◽  
Tanmoy Roy
Keyword(s):  
Surface Roughness ◽  
Cutting Tool ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Minimum Quantity Lubrication ◽  
Machining Process ◽  
Interface Temperature ◽  
Depth Of Cut ◽  
Work Piece ◽  
Substantial Impact

Abstract. Kinetic energy of a machining process is converted into heat energy. The generated heat at cutting tool and work piece interface has substantial impact on cutting tool life and quality of the work piece. On the other hand, development of advanced cutting tool materials, coatings and designs, along with a variety of strategies for lubrication, cooling and chip removal, make it possible to achieve the same or better surface quality with dry or Minimum Quantity Lubrication (MQL) machining than traditional wet machining. In addition, dry and MQL machining is more economical and environment friendly. In this work, 20 no. of experiments were carried out under dry machining conditions with different combinations of cutting speed, feed rate and depth of cut and corresponding cutting temperature and surface roughness are measured. The no. of experiments is determined through Design of Experiments (DOE). Nonlinear regression methodology is used to model the process using Response Surface Methodology (RSM). Multi-objective optimization is carried using Genetic Algorithm which ensures high productivity with good product quality.

scholarly journals The Effect of Material Behaviour on the Surface Roughness during Machining of H13 Tool Steel

2020 ◽  
Vol 9 (5) ◽  
pp. 131-136
Keyword(s):  
Surface Roughness ◽  
Strain Rate ◽  
Tool Steel ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Material Behaviour ◽  
H13 Tool Steel ◽  
Reduction Coefficient ◽  
Strain Rate Hardening ◽  
Carbide Insert

The aim of the present study is to know the effect of material properties on surface roughness during dry turning of H13 tool steel. Machining was performed using Tungaloy made carbide insert. Chip reduction coefficient (CRC) and surface roughness values (Ra) were experimentally determined. Twenty seven experiments were conducted following 33 factorial design. Subsequently, chip samples were examined under scanning electron microscope. Surface roughness values were found to be influenced by strain hardening and strain rate hardening of the material depending upon the values of speed, feed and depth of cut (d.o.c). Surface quality improves because of strain rate hardening at higher cutting speed.

Sign in / Sign up

Export Citation Format

Share Document