Effects of Insert Nose Radius and Processing Cutting Parameter on the Surface Roughness of Aisi 316 Stainless Steel

2010 ◽  
Vol 447-448 ◽  
pp. 51-54
Author(s):  
Mohd Fazuri Abdullah ◽  
Muhammad Ilman Hakimi Chua Abdullah ◽  
Abu Bakar Sulong ◽  
Jaharah A. Ghani
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Surface Finish ◽  
Feed Rate ◽  
Cutting Speed ◽  
Chip Thickness ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Nose Radius ◽  
Aisi 316

The effects of different cutting parameters, insert nose radius, cutting speed and feed rates on the surface quality of the stainless steel to be use in medical application. Stainless steel AISI 316 had been machined with three different nose radiuses (0.4 mm 0.8 mm, and 1.2mm), three different cutting speeds (100, 130, 170 m/min) and feed rates (0.1, 0.125, 0.16 mm/rev) while depth of cut keep constant at (0.4 mm). It is seen that the insert nose radius, feed rates, and cutting speed have different effect on the surface roughness. The minimum average surface roughness (0.225µm) has been measured using the nose radius insert (1.2 mm) at lowest feed rate (0.1 mm/rev). The highest surface roughness (1.838µm) has been measured with nose radius insert (0.4 mm) at highest feed rate (0.16 mm/rev). The analysis of ANOVA showed the cutting speed is not dominant in processing for the fine surface finish compared with feed rate and nose radius. Conclusion, surface roughness is decreasing with decreasing of the feed rate. High nose radius produce better surface finish than small nose radius because of the maximum uncut chip thickness decreases with increase of nose radius.

scholarly journals Influence of the Cutting Parameters on the Surface Roughness when Machining Hardened Steel with Ceramic and PCBN Cutting Tools

2015 ◽  
Vol 13 ◽  
pp. 19-22 ◽  
Author(s):  
Gabriel Benga ◽  
Danut Savu ◽  
Adrian Olei
Keyword(s):  
Surface Roughness ◽  
Surface Finish ◽  
Feed Rate ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Bearing Steel ◽  
Hardened Steel ◽  
Depth Of Cut ◽  
Cutting Regimes

The paper presents the influence of various cutting regimes on the surface roughness, when a hardened bearing steel has been machined using both ceramic and PCBN cutting tools. There were used different cutting conditions varying cutting speed, feed rate and depth of cut in order to determine the influence of each cutting parameter on the surface finish.

Optimization of Cutting Parameters for Turning Operation of Titanium Alloy Ti-6Al-4V Material Workpiece Using the Taguchi Method

2013 ◽  
Vol 685 ◽  
pp. 57-62
Author(s):  
Seyyed Pedram Shahebrahimi ◽  
Abdolrahman Dadvand
Keyword(s):  
Surface Roughness ◽  
Titanium Alloy ◽  
Taguchi Method ◽  
Surface Finish ◽  
Feed Rate ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Material Tool

One of the most important issues in turning operations is to choose suitable parameters in order to achieve a desired surface finish. The surface finish in machining operation depends on many parameters such as workpiece material, tool material, tool coating, machining parameters, etc. The purpose of this research is to focus on the analysis of optimum cutting parameters to get the lowest surface roughness in turning Titanium alloy Ti-6Al-4V with the insert with the standard code DNMG 110404 under dry cutting condition, by the Taguchi method. The turning parameters are evaluated as cutting speed of 14, 20 and 28 m/min, feed rate of 0.12, 0.14 and 0.16 mm/rev, depth of cut of 0.3, 0.6 and 1 mm, each at three levels. The Experiment was designed using the Taguchi method and 9 experiments were conducted by this process. The results are analyzed using analysis of variance method (ANOVA). The results of analysis show that the depth of cut has a significant role to play in producing lower surface roughness that is about 63.33% followed by feed rate about 30.25%, and cutting speed has less contribution on the surface roughness. Also it was realized that with the use of the confirmation test, the surface roughness improved by 227% from its initial state.

scholarly journals Effect of Cutting Insert Type on Surface Roughness of Hardened AISI 420 Stainless Steel

2021 ◽  
Vol 4 (1) ◽  
pp. 171-185
Author(s):  
Anıl Berk Dalkıran ◽  
Furkan Yılmaz ◽  
Samet Emre Bilim
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Feed Rate ◽  
Cutting Speed ◽  
High Strength ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Aisi 420 ◽  
Cutting Insert ◽  
Coated Carbide

AISI 420 stainless steel is one of the alloys that can be used in various applications due to its malleability, high strength, and weldability. In this study, the effects of cutting parameters (feed rate, depth of cut, and cutting speed) on the surface roughness were investigated during the turning of AISI 420 under dry test conditions using coated carbide and ceramic cutting inserts. Response surface methodology, analysis of variance, and statistical methods of the main effect plot were applied to investigate the effects of input parameters on response values. The results of this study showed that feed rate followed by the depth of cut had the most significant effect on output parameters. According to the experimental data, as the feed rate and depth of cut increase, the surface roughness increases.

OPTIMISING CUTTING PARAMETERS FOR HOT TURNING ON EN31 MATERIAL

2021 ◽  
Vol 5 (10) ◽  
Author(s):  
Prof. Hemant k. Baitule ◽  
Satish Rahangdale ◽  
Vaibhav Kamane ◽  
Saurabh Yende
Keyword(s):  
Surface Roughness ◽  
Surface Finish ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Machining Process ◽  
Depth Of Cut ◽  
Multiple Time ◽  
Turning Process ◽  
Workpiece Material ◽  
Hot Turning

In any type of machining process the surface roughness plays an important role. In these the product is judge on the basis of their (surface roughness) surface finish. In machining process there are four main cutting parameter i.e. cutting speed, feed rate, depth of cut, spindle speed. For obtaining good surface finish, we can use the hot turning process. In hot turning process we heat the workpiece material and perform turning process multiple time and obtain the reading. The taguchi method is design to perform an experiment and L18 experiment were performed. The result is analyzed by using the analysis of variance (ANOVA) method. The result Obtain by this method may be useful for many other researchers.

Statistical Study and Multi-Response Optimization of Cutting Parameters for Dry Turning Stainless Steel AISI 316L Using Cermet Tool

2020 ◽  
Vol 36 ◽  
pp. 28-46
Author(s):  
Youssef Touggui ◽  
Salim Belhadi ◽  
Salah Eddine Mechraoui ◽  
Mohamed Athmane Yallese ◽  
Mustapha Temmar
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Feed Rate ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Aisi 316L ◽  
Cutting Power ◽  
Dry Turning ◽  
Optimization Of Cutting Parameters

Stainless steels have gained much attention to be an alternative solution for many manufacturing industries due to their high mechanical properties and corrosion resistance. However, owing to their high ductility, their low thermal conductivity and high tendency to work hardening, these materials are classed as materials difficult to machine. Therefore, the main aim of the study was to examine the effect of cutting parameters such as cutting speed, feed rate and depth of cut on the response parameters including surface roughness (Ra), tangential cutting force (Fz) and cutting power (Pc) during dry turning of AISI 316L using TiCN-TiN PVD cermet tool. As a methodology, the Taguchi L27 orthogonal array parameter design and response surface methodology (RSM)) have been used. Statistical analysis revealed feed rate affected for surface roughness (79.61%) and depth of cut impacted for tangential cutting force and cutting power (62.12% and 35.68%), respectively. According to optimization analysis based on desirability function (DF), cutting speed of 212.837 m/min, 0.08 mm/rev feed rate and 0.1 mm depth of cut were determined to acquire high machined part quality

scholarly journals Investigations on Surface Roughness and Tool Wear Characteristics in Micro-Turning of Ti-6Al-4V Alloy

Materials ◽  
2020 ◽  
Vol 13 (13) ◽  
pp. 2998 ◽  
Author(s):  
Kubilay Aslantas ◽  
Mohd Danish ◽  
Ahmet Hasçelik ◽  
Mozammel Mia ◽  
Munish Gupta ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
Removal Rate ◽  
Cutting Speed ◽  
Small Diameter ◽  
Cutting Parameters ◽  
Ti6al4v Alloy ◽  
Depth Of Cut ◽  
Turning Process ◽  
Micro Turning

Micro-turning is a micro-mechanical cutting method used to produce small diameter cylindrical parts. Since the diameter of the part is usually small, it may be a little difficult to improve the surface quality by a second operation, such as grinding. Therefore, it is important to obtain the good surface finish in micro turning process using the ideal cutting parameters. Here, the multi-objective optimization of micro-turning process parameters such as cutting speed, feed rate and depth of cut were performed by response surface method (RSM). Two important machining indices, such as surface roughness and material removal rate, were simultaneously optimized in the micro-turning of a Ti6Al4V alloy. Further, the scanning electron microscope (SEM) analysis was done on the cutting tools. The overall results depict that the feed rate is the prominent factor that significantly affects the responses in micro-turning operation. Moreover, the SEM results confirmed that abrasion and crater wear mechanism were observed during the micro-turning of a Ti6Al4V alloy.

Effect of machining parameters on the surface finish of a metal matrix composite under dry cutting conditions

2015 ◽  
Vol 231 (6) ◽  
pp. 913-923 ◽  
Author(s):  
Brian Boswell ◽  
Mohammad Nazrul Islam ◽  
Ian J Davies ◽  
Alokesh Pramanik
Keyword(s):  
Surface Roughness ◽  
Metal Matrix Composite ◽  
Tool Life ◽  
Surface Finish ◽  
Feed Rate ◽  
Metal Matrix ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Dry Cutting

The machining of aerospace materials, such as metal matrix composites, introduces an additional challenge compared with traditional machining operations because of the presence of a reinforcement phase (e.g. ceramic particles or whiskers). This reinforcement phase decreases the thermal conductivity of the workpiece, thus, increasing the tool interface temperature and, consequently, reducing the tool life. Determining the optimum machining parameters is vital to maximising tool life and producing parts with the desired quality. By measuring the surface finish, the authors investigated the influence that the three major cutting parameters (cutting speed (50–150 m/min), feed rate (0.10–0.30 mm/rev) and depth of cut (1.0–2.0 mm)) have on tool life. End milling of a boron carbide particle-reinforced aluminium alloy was conducted under dry cutting conditions. The main result showed that contrary to the expectations for traditional machined alloys, the surface finish of the metal matrix composite examined in this work generally improved with increasing feed rate. The resulting surface roughness (arithmetic average) varied between 1.15 and 5.64 μm, with the minimum surface roughness achieved with the machining conditions of a cutting speed of 100 m/min, feed rate of 0.30 mm/rev and depth of cut of 1.0 mm. Another important result was the presence of surface microcracks in all specimens examined by electron microscopy irrespective of the machining condition or surface roughness.

scholarly journals Experimental Investigation on Surface Roughness and Tool Wear in Dry Machining of TiC Reinforced Aluminium LM6 Composite

2013 ◽  
Vol 773-774 ◽  
pp. 339-347 ◽  
Author(s):  
Muhammad Yusuf ◽  
M.K.A. Ariffin ◽  
N. Ismail ◽  
S. Sulaiman
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Feed Rate ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Carbide Tool ◽  
Dry Machining ◽  
Workpiece Surface ◽  
High Cutting Speed

With increasing quantities of applications of Metal Matrix Composites (MMCs), the machinablity of these materials has become important for investigation. This paper presents an investigation of surface roughness and tool wear in dry machining of aluminium LM6-TiC composite using uncoated carbide tool. The experiments carried out consisted of different cutting models based on combination of cutting speed, feed rate and depth of cut as the parameters of cutting process. The cutting models designed based on the Design of Experiment Response Surface Methodology. The objective of this research is finding the optimum cutting parameters based on workpiece surface roughness and cutting tool wear. The results indicated that the optimum workpiece surface roughness was found at high cutting speed of 250 m min-1 with various feed rate within range of 0.05 to 0.2 mm rev-1, and depth of cut within range of 0.5 to 1.5 mm. Turning operation at high cutting speed of 250 m min-1 produced faster tool wear as compared to low cutting speed of 175 m min-1 and 100 m min-1. The wear minimum (VB = 42 μm ) was found at cutting speed of 100 m min-1, feet rate of 0.2 mm rev-1, and depth of cut of 1.0 mm until the length of cut reached 4050 mm. Based on the results of the workpiece surface roughness and the tool flank wear, recommended that turning of LM6 aluminium with 2 wt % TiC composite using uncoated carbide tool should be carried out at cutting speed higher than 175 m min-1 but at feed rate of less than 0.05 mm rev-1 and depth of cut less than 1.0 mm.

Investigation of Chip and Surface Roughness when Milling AISI304 Stainless Steel

2017 ◽  
Vol 889 ◽  
pp. 152-158
Author(s):  
K. Kadirgama ◽  
K. Abou-El-Hossein
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Feed Rate ◽  
Prediction Models ◽  
Cutting Speed ◽  
Experimental Result ◽  
Quadratic Model ◽  
Depth Of Cut ◽  
Cutting Condition ◽  
Axial Depth

Stainless steel was used for many engineering applications. The optimum parameters needs to be identify to save the cutting tool usage and increase productivity. The purpose of this study is to develop the surface roughness mathematical model for AISI 304 stainless steel when milling using TiN (CVD) carbide tool. The milling process was done under various cutting condition which is cutting speed (1500, 2000 and 2500 rpm), feed rate (0.02, 0.03 and 0.04 mm/tooth) and axial depth (0.1, 0.2 and 0.3 mm). The first order model and quadratic model have been developed using Response Surface Method (RSM) with confident level 95%. The prediction models were comparing with the actual experimental results. It is found that quadratic model much fit the experimental result compare to linear model. In general, the results obtained from the mathematical models were in good agreement with those obtained from the machining experiments. Besides that, it is shown that the influence of cutting speed and feed rate are much higher on surface roughness compare to depth of cut. The optimum cutting speed, feed rate and axial depth is 2500 rpm, 0.0212 mm/tooth and 0.3mm respectively. Besides that, continues chip is produced at cutting speed 2500 rpm meanwhile discontinues chip produced at cutting speed 1500 rpm.

scholarly journals Investigate the Effect of Cutting Parameters on Surface Roughness When Milling X12m Steel

2021 ◽  
pp. 258-263
Author(s):  
Do Thi Kim Lien ◽  
Nguyen Dinh Man ◽  
Phung Tran Dinh
Keyword(s):  
Experimental Study ◽  
Surface Roughness ◽  
Feed Rate ◽  
Cutting Tool ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Face Milling ◽  
Negligible Effect ◽  
Depth Of Cut ◽  
The Relationship

In this paper, an experimental study on the effect of cutting parameters on surface roughness was conducted when milling X12M steel. The cutting tool used in this study is a face milling cutter. The material that is used to make the insert is the hard alloy T15K6. The cutting parameters covered in this study include the cutting speed, the feed rate and depth of cut. The experiments are performed in the form of a rotating center composite design. The analysis shows that for both Ra and Rz: (1) the feed rate has the greatest influence on the surface roughness while the depth of cut, the cutting speed has a negligible effect on the surface roughness. (2) only the interaction between the feed rate and the depth of the cut has a significant effect on both Ra and Rz while the interaction between the cutting speed and the feed rate, the interaction between the cutting speed and the depth of cut have a negligible effect on surface roughness. A regression equation showing the relationship between Ra, Rz, and cutting parameters has also been built in this study.

Sign in / Sign up

Export Citation Format

Share Document