Research on Precast Roof Truss of Prestressed Concrete Square Pile

2014 ◽  
Vol 488-489 ◽  
pp. 359-364
Author(s):  
Jia Bin Liu ◽  
Zheng Xing Guo ◽  
Le Qi Chen
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Prestressed Concrete ◽  
Control Method ◽  
Optimal Solution ◽  
Bending Moment ◽  
Scale Model ◽  
Element Analysis ◽  
Design Load ◽  
Roof Truss

The precast roof truss of prestressed concrete square pile is a new self-balancing system composed of prestressed concrete square pile, strut and steel tension rod. Based on finite element analysis methods, the bending moment and deformation under most unfavorable design load was checked upon crack resistant bending moment to verify its engineering feasibility, the optimal prestressed value was analyzed to get the camber of the top chord beam, and the optimal tension method for bottom chord tension rod was determined. Compared with finite element analysis results, the full scale model test was carried out to further verify its engineering feasibility and some optimization recommendation was proposed. It suggests that the tension order of middle section before diagonal rod, initial prestressed value of 10t, and prestressed control method of monitoring camber at midspan is the most reasonable and optimal solution.

FINITE ELEMENT ANALYSIS OF PRESTRESSED CONCRETE VOIDED BRIDGE DECKS

PCI Journal ◽  
1973 ◽  
Vol 18 (3) ◽  
pp. 51-66 ◽  
Author(s):  
J. C. Jofriet ◽  
G. M. McNeice ◽  
P. Csagoly
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Prestressed Concrete ◽  
Bridge Decks ◽  
Element Analysis

scholarly journals A Review on Numerical Analysis of RC Flat Slabs Exposed to Fire

2020 ◽  
Vol 27 (1) ◽  
pp. 1-5
Author(s):  
Hanadi Naji ◽  
Nibras Khalid ◽  
Mutaz Medhlom
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Numerical Analysis ◽  
Bending Moment ◽  
Mechanical And Thermal Properties ◽  
Vertical Deflection ◽  
Element Analysis ◽  
Flat Slabs ◽  
Numerical Studies ◽  
The Finite Element Analysis

This paper aims at presenting and discussing the numerical studies performed to estimate the mechanical and thermal behavior of RC flat slabs at elevated temperature and fire. The numerical analysis is carried out using finite element programs by developing models to simulate the performance of the buildings subjected to fire. The mechanical and thermal properties of the materials obtained from the experimental work are involved in the modeling that the outcomes will be more realistic. Many parameters related to fire resistance of the flat slabs have been studied and the finite element analysis results reveal that the width and thickness of the slab, the temperature gradient, the fire direction, the exposure duration and the thermal restraint are important factors that influence the vertical deflection, bending moment and force membrane of the flat slabs exposed to fire. However, the validation of the models is verified by comparing their results to the available experimental date. The finite element modeling contributes in saving cost and time consumed by experiments.

Finite-Element Analysis of Scale-Model Frame-Supported Tents

1975 ◽  
Author(s):  
Paul J. Remington ◽  
John C. O'Callahan ◽  
Richard Madden
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Scale Model ◽  
Element Analysis

Dynamic Interaction of High-Voltage Power Transformer Bushings, Turrets, and Tanks

2018 ◽  
Vol 34 (1) ◽  
pp. 397-421 ◽  
Author(s):  
Guo-Liang Ma ◽  
Qiang Xie ◽  
Andrew Whittaker
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
High Voltage ◽  
Power Transformer ◽  
Bending Moment ◽  
Dynamic Interaction ◽  
Electrical Performance ◽  
Element Analysis ◽  
Ground Shaking ◽  
Input Motion

High-voltage (HV) bushings are attached to a power transformer tank either directly or indirectly via turrets. Turrets are used to achieve electrical performance requirements, but their potential impact on the seismic performance of the supported bushings has not been considered. Earthquake simulator testing and finite-element analysis were used to quantify the amplification of ground shaking through tanks (220- and 500-kV) and turrets to the points of attachment of roof- and sidewall-supported bushings. Substantial amplification of motion was seen in both physical experiments and numerical simulations. Sample bracing schemes external to the transformer tank were investigated to potentially reduce the motions experienced by the bushings. Bushing tip displacements were reduced in all stiffening cases studied, but the outcomes for bending moment at the bushing-turret connection were mixed, with no change in some cases and significant reductions in others. The physical and numerical studies described in this paper make clear the importance of dynamic interaction of bushings, turrets, and the power transformer tank. The methods currently used to address the amplification of input motion from the base of a tank to the points of attachment of its bushing are inadequate. The seismic design of HV power transformer tanks and turrets should be supported by finite-element analysis of validated models to avoid dynamic interaction in the bushing-turret-tank system, to minimize seismic demand on the transformer bushings, and to minimize the risk of substation damage in earthquakes.

Capacity Analysis of PE Pipeline With Non-Planar Defect

2013 ◽  
Author(s):  
Weijie Jiang ◽  
Jianping Zhao ◽  
Dingyue Chen
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Constitutive Model ◽  
Mechanical Performance ◽  
Orthogonal Design ◽  
Bending Moment ◽  
Limit Load ◽  
Capacity Analysis ◽  
Element Analysis ◽  
Load Factors

A tensile test of buried PE pipe is designed to test the mechanical performance. Then the constitutive model for the PE pipe can be established. The limit load of the PE pipe with local thinning defect can be studied with the method of combining the orthogonal design of experiment and finite element analysis. Then the factors of local thinning defect pipe limit load factors can be analyzed. The results show that the depth of the defect has a great effect on the limit load (internal pressure and bending moment) of PE pipe. The effects that the axial length of the defect and the circumferential length of the defect have on the limit load are not significant.

Comparative Safety Analysis of Different Bollard Supporting Structures

2013 ◽  
Vol 325-326 ◽  
pp. 1297-1300
Author(s):  
Long Zhang ◽  
Jian Xing Yu ◽  
Wei Lin Ma ◽  
Bao Jian Wang
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Safety Analysis ◽  
Ansys Software ◽  
Element Analysis ◽  
Strength Criteria ◽  
Design Load ◽  
Comparative Safety ◽  
Supporting Structures

Detailed finite element analysis has been carried out for different bollard supporting structures by ANSYS software. From the analysis results, it can be seen that the bollard supporting structures are of adequate strength to take the design load transferred from the mooring rope during operation considering the requirement on strength criteria from IACS, and strength check is performed in accordance with the updated relevant ABS standard. Finally, a comparison of these different bollard supporting structures is made to find out their own advantages from safety and other aspects.

Sign in / Sign up

Export Citation Format

Share Document