Development of Boundary Layer in CRIACIV in Florence (Prato) and Comparison with CFD

2016 ◽  
Vol 820 ◽  
pp. 359-364
Author(s):  
Marek Magát ◽  
Ivana Olekšáková ◽  
Juraj Žilinský

In this article are described the results from testing profile of atmospheric boundary layer in BLWT (Boundary layer wind tunnel) in Florence (Prato), Italy with emphasis on comparison of the results with simulations in CFD (Computational fluid dynamics) software OpenFoam. The values are compared with calculated values from EuroCode.

2014 ◽  
Vol 14 (23) ◽  
pp. 12631-12648 ◽  
Author(s):  
L. Huang ◽  
S. L. Gong ◽  
M. Gordon ◽  
J. Liggio ◽  
R. Staebler ◽  
...  

Abstract. Many studies have shown that on-road vehicle emissions are the dominant source of ultrafine particles (UFPs; diameter < 100 nm) in urban areas and near-roadway environments. In order to advance our knowledge on the complex interactions and competition among atmospheric dilution, dispersion, and dynamics of UFPs, an aerosol dynamics–computational fluid dynamics (CFD) coupled model is developed and validated against field measurements. A unique approach of applying periodic boundary conditions is proposed to model pollutant dispersion and dynamics in one unified domain from the tailpipe level to the ambient near-road environment. This approach significantly reduces the size of the computational domain, and therefore allows fast simulation of multiple scenarios. The model is validated against measured turbulent kinetic energy (TKE) and horizontal gradient of pollution concentrations perpendicular to a major highway. Through a model sensitivity analysis, the relative importance of individual aerosol dynamical processes on the total particle number concentration (N) and particle number–size distribution (PSD) near a highway is investigated. The results demonstrate that (1) coagulation has a negligible effect on N and particle growth, (2) binary homogeneous nucleation (BHN) of H2SO4–H2O is likely responsible for elevated N closest to the road, and (3) N and particle growth are very sensitive to the condensation of semi-volatile organics (SVOCs), particle dry deposition, and the interaction between these processes. The results also indicate that, without the proper treatment of the atmospheric boundary layer (i.e., its wind profile and turbulence quantities), the nucleation rate would be underestimated by a factor of 5 in the vehicle wake region due to overestimated dilution. Therefore, introducing atmospheric boundary layer (ABL) conditions to activity-based emission models may potentially improve their performance in estimating UFP traffic emissions.


2013 ◽  
Vol 477-478 ◽  
pp. 181-185
Author(s):  
Matheus De Queiroz ◽  
Guilherme Loyola França De Vasconcellos ◽  
Cristiana Brasil Maia ◽  
Julien Weiss ◽  
Sérgio De Morais Hanriot

This paper presents a study that correlates the capacity of two advection schemes in foreseeing flow separation inside a boundary layer wind tunnel (BLWT herein after). The geometry of the BLWT forces the generation of a turbulent separation bubble. Numerical simulations were carried out with the commercial Computational Fluid Dynamics software ANSYS-CFX®. The high-resolution advection scheme is shown to be more appropriate than the upwind scheme in predicting flows where properties are subject to strong gradients, such as pressure and velocity.


2021 ◽  
Vol 143 (4) ◽  
Author(s):  
Dwaipayan Sarkar ◽  
Eric Savory

Abstract This work models the spatial decay of freestream turbulence using three different commercial computational fluid dynamics (CFD) codes: Fluent, star-ccm+, and cfx. The two-equation shear stress transport k–ω (SST-k–ω) steady Reynolds-averaged-Navier–Stokes (RANS) model was used, within each of these three different commercial codes, and the modeling variations were analyzed. Comparison of the results from the SST-k–ω model with experiments and large eddy simulation (LES) (carried out using star-ccm+) were also made, which reveal that all the commercial CFD codes demonstrate either a higher or slower rate of spatial turbulent kinetic energy (TKE) decay. Attempts were then made to unify the resultant modeling approach between these three CFD tools, by careful manipulation of the inlet boundary conditions and subsequent fine-tuning of the SST-k–ω model constant (β∞∗). The results obtained not only displayed uniformity among the three CFD codes but also demonstrated a much better agreement to the experiments and the LES results. Thereafter, the optimized model coefficient (β∞∗) was integrated with the three-equation k–kl–ω transition model to examine its applicability in modeling a turbulent boundary layer flow over a flat plate with low incoming turbulence. The results showed good agreement with the theoretical boundary layer correlations, with correct prediction of the transition location. The findings from this study can be used as a suitable modeling method to accurately model the effects of freestream turbulence on bluff-body and boundary layer flows.


2021 ◽  
Vol 11 (4) ◽  
pp. 1642
Author(s):  
Yuxiang Zhang ◽  
Philip Cardiff ◽  
Jennifer Keenahan

Engineers, architects, planners and designers must carefully consider the effects of wind in their work. Due to their slender and flexible nature, long-span bridges can often experience vibrations due to the wind, and so the careful analysis of wind effects is paramount. Traditionally, wind tunnel tests have been the preferred method of conducting bridge wind analysis. In recent times, owing to improved computational power, computational fluid dynamics simulations are coming to the fore as viable means of analysing wind effects on bridges. The focus of this paper is on long-span cable-supported bridges. Wind issues in long-span cable-supported bridges can include flutter, vortex-induced vibrations and rain–wind-induced vibrations. This paper presents a state-of-the-art review of research on the use of wind tunnel tests and computational fluid dynamics modelling of these wind issues on long-span bridges.


Sign in / Sign up

Export Citation Format

Share Document