Piezoelectric Energy Harvesting from Floor Using Wounded PVDF Films

2014 ◽  
Vol 1030-1032 ◽  
pp. 3-7 ◽  
Author(s):  
E. Bischur ◽  
N. Schwesinger
Keyword(s):  
Energy Harvesting ◽  
Field Strength ◽  
Mechanical Energy ◽  
Wireless Systems ◽  
Process Step ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Sufficient Energy ◽  
Polarization Temperature ◽  
Electrical Loads

Energy harvesters of PVDF can be used to power small electrical loads or wireless sensor systems. Simple technologies are sufficient for the fabrication of these harvesting modules. Critical process step is the polarization of the piezoelectric material. Main piezoelectric parameters depend strongly on the polarization material. Particularly, the electric field strength and the polarization temperature influence the remanent polarization of PVDF. Dielectric breakdowns of the film at higher temperatures prevent a sufficient polarization. At least, all modules were polarized at a field strength of 100 – 120 MV/m and a temperature of 90°C.Modules with dimensions of 165mm x 95mm x 1.5mm were used to power a commercial available “development kit for Energy Harvesting Wireless systems” (EnOcean ‘EDK 300’). The modules possess of 20 layers of PVDF. Each module was connected via a standard four diode full rectifier bridge with the development kit EDK 300. Positioned underneath a parquet floor (thickness=10mm), the modules converted mechanical energy of footsteps into electricity. Goal of these investigations were to find out configurations suited to generate a sufficient energy level to supply the operation of the EDK 300. Two capacitors in the development kit are used to start the operation of the kit (C1=470μF) and to store converted energy (C2=0.25F). Already a few steps onto one module were sufficient to charge C1 and to start the operation of the EDK 300. Following steps (>100) produced energy which was stored in C2.

scholarly journals The State-of-the-Art Brief Review on Piezoelectric Energy Harvesting from Flow-Induced Vibration

2021 ◽  
Vol 2021 ◽  
pp. 1-19
Author(s):  
Hongjun Zhu ◽  
Tao Tang ◽  
Huohai Yang ◽  
Junlei Wang ◽  
Jinze Song ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Bluff Body ◽  
Mechanical Energy ◽  
Wake Flow ◽  
Structural Vibration ◽  
Small Scale ◽  
Flow Induced Vibration ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Self Powered

Flow-induced vibration (FIV) is concerned in a broad range of engineering applications due to its resultant fatigue damage to structures. Nevertheless, such fluid-structure coupling process continuously extracts the kinetic energy from ambient fluid flow, presenting the conversion potential from the mechanical energy to electricity. As the air and water flows are widely encountered in nature, piezoelectric energy harvesters show the advantages in small-scale utilization and self-powered instruments. This paper briefly reviewed the way of energy collection by piezoelectric energy harvesters and the various measures proposed in the literature, which enhance the structural vibration response and hence improve the energy harvesting efficiency. Methods such as irregularity and alteration of cross-section of bluff body, utilization of wake flow and interference, modification and rearrangement of cantilever beams, and introduction of magnetic force are discussed. Finally, some open questions and suggestions are proposed for the future investigation of such renewable energy harvesting mode.

scholarly journals Acoustic Energy Harvesting Through Multilayer Piezoelectric Harvester Model

2020 ◽  
Vol 9 (3) ◽  
pp. 1848-1856
Keyword(s):  
Energy Harvesting ◽  
Low Power ◽  
Mechanical Energy ◽  
Scaling Analysis ◽  
Ambient Vibrations ◽  
Specific Element ◽  
Power Sources ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Effective Transfer

Low-power requirements of contemporary sensing technology attract research on alternate power sources that can replace batteries. Energy harvesters’ function as power sources for sensors and other low-power devices by transducing the ambient energy into usable electrical form. Energy harvesters absorbing the ambient vibrations that have potential to deliver uninterrupted power to sensing nodes installed in remote and vibration rich environments motivate the research in vibrational energy harvesting. Piezoelectric bimorphs have been demonstrating a pre-eminence in converting the mechanical energy in ambient vibrations into electrical energy. Improving the performance of these harvesters is pivotal, as the energy in ambient vibrations is innately low. In this paper, we propose a mechanism namely MultilayerPEHM (Piezoelectric Energy Harvester Model) which helps in converting the waste or unused energy into the useful energy. Multilayer-PEHM contains the various layer, which is placed one over the other, each layer is placed with specific element according to their properties and size, the size of the layer plays an important part for achieving efficiency. Furthermore, this paper presents an audit of the energy available in a vibrating source and design for effective transfer of the energy to harvesters, secondly, design of vibration energy harvesters with a focus to enhance their performance, and lastly, identification of key performance metrics influencing conversion efficiencies and scaling analysis for these acoustic harvesters. Typical vibration levels in stationary installations such as surfaces of blowers and ducts, and in mobile platforms such as light and heavy transport vehicles, are determined by measuring the acceleration signal. The frequency content in the signal is determined from the Fast Fourier Transform.

Material influence in newly proposed ferroelectric energy harvesters

2018 ◽  
Vol 29 (16) ◽  
pp. 3305-3316 ◽  
Author(s):  
Dan Wang ◽  
Roderick Melnik ◽  
Linxiang Wang
Keyword(s):  
Energy Harvesting ◽  
Mechanical Energy ◽  
Phase Field Model ◽  
Ferroelectric Materials ◽  
Equivalent Material ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
New Strategy ◽  
Novel Method ◽  
Harvesting Process

Recently, a novel method for mechanical energy harvesting has been proposed, which is based on stress-induced polarization switching in ferroelectric materials. Compared with the traditional piezoelectric energy harvesters, a huge improvement in the output energy has already been theoretically demonstrated. In this article, the influence of different materials on the energy-harvesting performance associated with this new strategy is further studied. The state-of-the-art phase-field model is adopted to investigate the nonlinear hysteretic energy-harvesting process in two nanoscale ferroelectric energy harvesters, which are respectively based on two typical ferroelectric materials—single-crystal BaTiO3 and PbTiO3. In both cases, the effects of the bias voltage and bias resistance are carefully investigated and the optimum values are obtained. Later, the energy-harvesting process and energy flow details in both harvesters working at the optimum conditions are presented and carefully compared in the context of real applications. Furthermore, the energy-harvesting performance of a BaTiO3-based nanoscale piezoelectric energy harvester with equivalent material size is additionally simulated with the finite element method and compared with the corresponding results of the ferroelectric energy harvesters, where obvious advantages associated with the new strategy are demonstrated.

High and thermal-stable piezoelectricity in relaxor-based ferroelectrics for mechanical energy harvesting

2021 ◽  
Author(s):  
Xiaole Yu ◽  
Yudong Hou ◽  
Mupeng Zheng ◽  
Mankang Zhu
Keyword(s):  
Power Generation ◽  
Energy Harvesting ◽  
Mechanical Energy ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Generation Capacity ◽  
Thermal Stable

The utilization of relaxor-based ferroelectrics with high piezoelectricity is considered to be an effective way to enhance the power generation capacity of piezoelectric energy harvesters (PEHs). However, the severe depolarization...

Multimodal pizza-shaped piezoelectric vibration-based energy harvesters

2021 ◽  
pp. 1045389X2110069
Author(s):  
Virgilio J Caetano ◽  
Marcelo A Savi
Keyword(s):  
Energy Harvesting ◽  
Frequency Spectrum ◽  
Optimization Procedure ◽  
Single Mode ◽  
Ambient Vibration ◽  
Vibration Source ◽  
Element Analysis ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Harvesting Systems

Energy harvesting from ambient vibration through piezoelectric devices has received a lot of attention in recent years from both academia and industry. One of the main challenges is to develop devices capable of adapting to diverse sources of environmental excitation, being able to efficiently operate over a broadband frequency spectrum. This work proposes a novel multimodal design of a piezoelectric energy harvesting system to harness energy from a wideband ambient vibration source. Circular-shaped and pizza-shaped designs are employed as candidates for the device, comparing their performance with classical beam-shaped devices. Finite element analysis is employed to model system dynamics using ANSYS Workbench. An optimization procedure is applied to the system aiming to seek a configuration that can extract energy from a broader frequency spectrum and maximize its output power. A comparative analysis with conventional energy harvesting systems is performed. Numerical simulations are carried out to investigate the harvester performances under harmonic and random excitations. Results show that the proposed multimodal harvester has potential to harness energy from broadband ambient vibration sources presenting performance advantages in comparison to conventional single-mode energy harvesters.

Geometric and Material Optimization of Vortex-Induced Vibration Micro Energy Harvesters for Localized Wind Environments

2012 ◽  
Author(s):  
Jesse J. French ◽  
Colton T. Sheets
Keyword(s):  
Energy Harvesting ◽  
Power Output ◽  
Fluid Velocity ◽  
Frequency Variation ◽  
Vortex Induced Vibration ◽  
Energy Harvesters ◽  
Wind Speeds ◽  
Material Optimization ◽  
Piezoelectric Energy ◽  
Wind Velocities

Wind energy capture in today’s environment is often focused on producing large amounts of power through massive turbines operating at high wind speeds. The device presented by the authors performs on the extreme opposite scale of these large wind turbines. Utilizing vortex induced vibration combined with developed and demonstrated piezoelectric energy harvesting techniques, the device produces power consistent with peer technologies in the rapidly growing field of micro-energy harvesting. Vortex-induced vibrations in the Karman vortex street are the catalyst for energy production of the device. To optimize power output, resonant frequency of the harvester is matched to vortex shedding frequency at a given wind speed, producing a lock-on effect that results in the greatest amplitude of oscillation. The frequency of oscillation is varied by altering the effective spring constant of the device, thereby allowing for “tuning” of the device to specific wind environments. While localized wind conditions are never able to be predicted with absolute certainty, patterns can be established through thorough data collection. Sampling of local wind conditions led to the design and testing of harvesters operating within a range of wind velocities between approximately 4 mph and 25 mph. For the extremities of this range, devices were constructed with resonant frequencies of approximately 17 and 163 Hz. Frequency variation was achieved through altering the material composition and geometry of the energy harvester. Experimentation was performed on harvesters to determine power output at optimized fluid velocity, as well as above and below. Analysis was also conducted on shedding characteristics of the device over the tested range of wind velocities. Computational modeling of the device is performed and compared to experimentally produced data.

scholarly journals Theory of energy harvesting from heartbeat including the effects of pleural cavity and respiration

2017 ◽  
Vol 473 (2207) ◽  
pp. 20170615 ◽  
Author(s):  
Yangyang Zhang ◽  
Bingwei Lu ◽  
Chaofeng Lü ◽  
Xue Feng
Keyword(s):  
Energy Harvesting ◽  
Pleural Cavity ◽  
Scaling Law ◽  
Battery Life ◽  
Deformation Model ◽  
Experimental Measurements ◽  
Combined System ◽  
Energy Harvesters ◽  
Piezoelectric Energy

Self-powered implantable devices with flexible energy harvesters are of significant interest due to their potential to solve the problem of limited battery life and surgical replacement. The flexible electronic devices made of piezoelectric materials have been employed to harvest energy from the motion of biological organs. Experimental measurements show that the output voltage of the device mounted on porcine left ventricle in chest closed environment decreases significantly compared to the case of chest open. A restricted-space deformation model is proposed to predict the impeding effect of pleural cavity, surrounding tissues, as well as respiration on the efficiency of energy harvesting from heartbeat using flexible piezoelectric devices. The analytical solution is verified by comparing theoretical predictions to experimental measurements. A simple scaling law is established to analyse the intrinsic correlations between the normalized output power and the combined system parameters, i.e. the normalized permitted space and normalized electrical load. The results may provide guidelines for optimization of in vivo energy harvesting from heartbeat or the motions of other biological organs using flexible piezoelectric energy harvesters.

Energy harvesting from quasi-static deformations via bilaterally constrained strips

2018 ◽  
Vol 29 (18) ◽  
pp. 3572-3581
Author(s):  
Suihan Liu ◽  
Ali Imani Azad ◽  
Rigoberto Burgueño
Keyword(s):  
Energy Harvesting ◽  
Low Power ◽  
Mechanical Energy ◽  
Electrical Power ◽  
Energy Resource ◽  
Electrical Energy ◽  
Piezoelectric Energy Harvesting ◽  
Power Budget ◽  
Piezoelectric Energy ◽  
Static Conditions

Piezoelectric energy harvesting from ambient vibrations is well studied, but harvesting from quasi-static responses is not yet fully explored. The lack of attention is because quasi-static actions are much slower than the resonance frequency of piezoelectric oscillators to achieve optimal outputs; however, they can be a common mechanical energy resource: from large civil structure deformations to biomechanical motions. The recent advances in bio-micro-electro-mechanical systems and wireless sensor technologies are motivating the study of piezoelectric energy harvesting from quasi-static conditions for low-power budget devices. This article presents a new approach of using quasi-static deformations to generate electrical power through an axially compressed bilaterally constrained strip with an attached piezoelectric layer. A theoretical model was developed to predict the strain distribution of the strip’s buckled configuration for calculating the electrical energy generation. Results from an experimental investigation and finite element simulations are in good agreement with the theoretical study. Test results from a prototyped device showed that a peak output power of 1.33 μW/cm2 was generated, which can adequately provide power supply for low-power budget devices. And a parametric study was also conducted to provide design guidance on selecting the dimensions of a device based on the external embedding structure.

Embedded Metamaterial Subframe Patch for Increased Power Output of Piezoelectric Energy Harvesters

2021 ◽  
pp. 1-9
Author(s):  
Saman Farhangdoust ◽  
Gary Georgeson ◽  
Jeong-Beom Ihn ◽  
Armin Mehrabi
Keyword(s):  
Energy Harvesting ◽  
Cantilever Beam ◽  
Renewable Energy Sources ◽  
Piezoelectric Element ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Harvesting Systems ◽  
Host Structure ◽  
Self Powered ◽  
Low Efficiency

Abstract These days, piezoelectric energy harvesting (PEH) is introduced as one of the clean and renewable energy sources for powering the self-powered sensors utilized for wireless condition monitoring of structures. However, low efficiency is the biggest drawback of the PEHs. This paper introduces an innovative embedded metamaterial subframe (MetaSub) patch as a practical solution to address the low throughput limitation of conventional PEHs whose host structure has already been constructed or installed. To evaluate the performance of the embedded MetaSub patch (EMSP), a cantilever beam is considered as the host structure in this study. The EMSP transfers the auxetic behavior to the piezoelectric element (PZT) wherever substituting a regular beam with an auxetic beam is either impracticable or suboptimal. The concept of the EMSP is numerically validated, and the COMSOL Multiphysics software was employed to investigate its performance when a cantilever beam is subjected to different amplitude and frequency. The FEM results demonstrate that the harvesting power in cases that use the EMSP can be amplified up to 5.5 times compared to a piezoelectric cantilever energy harvester without patch. This paper opens up a great potential of using EMSP for different types of energy harvesting systems in biomedical, acoustics, civil, electrical, aerospace, and mechanical engineering applications.

Sign in / Sign up

Export Citation Format

Share Document