scholarly journals Acoustic Energy Harvesting Through Multilayer Piezoelectric Harvester Model

2020 ◽  
Vol 9 (3) ◽  
pp. 1848-1856
Keyword(s):  
Energy Harvesting ◽  
Low Power ◽  
Mechanical Energy ◽  
Scaling Analysis ◽  
Ambient Vibrations ◽  
Specific Element ◽  
Power Sources ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Effective Transfer

Low-power requirements of contemporary sensing technology attract research on alternate power sources that can replace batteries. Energy harvesters’ function as power sources for sensors and other low-power devices by transducing the ambient energy into usable electrical form. Energy harvesters absorbing the ambient vibrations that have potential to deliver uninterrupted power to sensing nodes installed in remote and vibration rich environments motivate the research in vibrational energy harvesting. Piezoelectric bimorphs have been demonstrating a pre-eminence in converting the mechanical energy in ambient vibrations into electrical energy. Improving the performance of these harvesters is pivotal, as the energy in ambient vibrations is innately low. In this paper, we propose a mechanism namely MultilayerPEHM (Piezoelectric Energy Harvester Model) which helps in converting the waste or unused energy into the useful energy. Multilayer-PEHM contains the various layer, which is placed one over the other, each layer is placed with specific element according to their properties and size, the size of the layer plays an important part for achieving efficiency. Furthermore, this paper presents an audit of the energy available in a vibrating source and design for effective transfer of the energy to harvesters, secondly, design of vibration energy harvesters with a focus to enhance their performance, and lastly, identification of key performance metrics influencing conversion efficiencies and scaling analysis for these acoustic harvesters. Typical vibration levels in stationary installations such as surfaces of blowers and ducts, and in mobile platforms such as light and heavy transport vehicles, are determined by measuring the acceleration signal. The frequency content in the signal is determined from the Fast Fourier Transform.

Energy harvesting from quasi-static deformations via bilaterally constrained strips

2018 ◽  
Vol 29 (18) ◽  
pp. 3572-3581
Author(s):  
Suihan Liu ◽  
Ali Imani Azad ◽  
Rigoberto Burgueño
Keyword(s):  
Energy Harvesting ◽  
Low Power ◽  
Mechanical Energy ◽  
Electrical Power ◽  
Energy Resource ◽  
Electrical Energy ◽  
Piezoelectric Energy Harvesting ◽  
Power Budget ◽  
Piezoelectric Energy ◽  
Static Conditions

Piezoelectric energy harvesting from ambient vibrations is well studied, but harvesting from quasi-static responses is not yet fully explored. The lack of attention is because quasi-static actions are much slower than the resonance frequency of piezoelectric oscillators to achieve optimal outputs; however, they can be a common mechanical energy resource: from large civil structure deformations to biomechanical motions. The recent advances in bio-micro-electro-mechanical systems and wireless sensor technologies are motivating the study of piezoelectric energy harvesting from quasi-static conditions for low-power budget devices. This article presents a new approach of using quasi-static deformations to generate electrical power through an axially compressed bilaterally constrained strip with an attached piezoelectric layer. A theoretical model was developed to predict the strain distribution of the strip’s buckled configuration for calculating the electrical energy generation. Results from an experimental investigation and finite element simulations are in good agreement with the theoretical study. Test results from a prototyped device showed that a peak output power of 1.33 μW/cm2 was generated, which can adequately provide power supply for low-power budget devices. And a parametric study was also conducted to provide design guidance on selecting the dimensions of a device based on the external embedding structure.

scholarly journals The State-of-the-Art Brief Review on Piezoelectric Energy Harvesting from Flow-Induced Vibration

2021 ◽  
Vol 2021 ◽  
pp. 1-19
Author(s):  
Hongjun Zhu ◽  
Tao Tang ◽  
Huohai Yang ◽  
Junlei Wang ◽  
Jinze Song ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Bluff Body ◽  
Mechanical Energy ◽  
Wake Flow ◽  
Structural Vibration ◽  
Small Scale ◽  
Flow Induced Vibration ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Self Powered

Flow-induced vibration (FIV) is concerned in a broad range of engineering applications due to its resultant fatigue damage to structures. Nevertheless, such fluid-structure coupling process continuously extracts the kinetic energy from ambient fluid flow, presenting the conversion potential from the mechanical energy to electricity. As the air and water flows are widely encountered in nature, piezoelectric energy harvesters show the advantages in small-scale utilization and self-powered instruments. This paper briefly reviewed the way of energy collection by piezoelectric energy harvesters and the various measures proposed in the literature, which enhance the structural vibration response and hence improve the energy harvesting efficiency. Methods such as irregularity and alteration of cross-section of bluff body, utilization of wake flow and interference, modification and rearrangement of cantilever beams, and introduction of magnetic force are discussed. Finally, some open questions and suggestions are proposed for the future investigation of such renewable energy harvesting mode.

scholarly journals Piezoelectric energy harvesting pedal integrated with a compliant load amplifier

2019 ◽  
Vol 11 (1) ◽  
pp. 168781401882014
Author(s):  
YiHe Zhang ◽  
Chul-Hee Lee
Keyword(s):  
Energy Harvesting ◽  
Low Power ◽  
Alternative Energy ◽  
Compliant Mechanism ◽  
Piezoelectric Materials ◽  
Mechanical Energy ◽  
Optimization Methods ◽  
Energy Output ◽  
Element Analysis ◽  
Piezoelectric Energy

Energy generation technologies that use piezoelectric materials as uninterrupted power supplies are one of the most practical solutions of low-power wireless sensor network. The piezoelectric generator collects mechanical energy from the environment and transforms it into electricity to supply to microelectronic devices. Thus, these alternative energy sources can reduce the consumption of batteries, thereby reducing environmental pollution. Piezoelectric materials can work in the bending, compression, and shear modes, which are named as d31, d33, and d15 modes, respectively. In this study, a piezo stack which worked in d31 mode has been designed and integrated into an energy harvesting pedal. A novel compliant amplifying mechanism has to be designed to amplify the input load so that the high-stiffness piezoelectric stack can achieve a large energy output at a lower input force. This compliant mechanism has been designed by the pseudo-rigid-body and topology optimization methods. The amplification ratios of different sized flexible amplification mechanisms are calculated through the finite element analysis and validated by experiments. Finally, a pedal generator has been made and the test results show that the collected electricity can effectively drive a low-power microcontroller, sensor, and other devices of these kinds.

Material influence in newly proposed ferroelectric energy harvesters

2018 ◽  
Vol 29 (16) ◽  
pp. 3305-3316 ◽  
Author(s):  
Dan Wang ◽  
Roderick Melnik ◽  
Linxiang Wang
Keyword(s):  
Energy Harvesting ◽  
Mechanical Energy ◽  
Phase Field Model ◽  
Ferroelectric Materials ◽  
Equivalent Material ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
New Strategy ◽  
Novel Method ◽  
Harvesting Process

Recently, a novel method for mechanical energy harvesting has been proposed, which is based on stress-induced polarization switching in ferroelectric materials. Compared with the traditional piezoelectric energy harvesters, a huge improvement in the output energy has already been theoretically demonstrated. In this article, the influence of different materials on the energy-harvesting performance associated with this new strategy is further studied. The state-of-the-art phase-field model is adopted to investigate the nonlinear hysteretic energy-harvesting process in two nanoscale ferroelectric energy harvesters, which are respectively based on two typical ferroelectric materials—single-crystal BaTiO3 and PbTiO3. In both cases, the effects of the bias voltage and bias resistance are carefully investigated and the optimum values are obtained. Later, the energy-harvesting process and energy flow details in both harvesters working at the optimum conditions are presented and carefully compared in the context of real applications. Furthermore, the energy-harvesting performance of a BaTiO3-based nanoscale piezoelectric energy harvester with equivalent material size is additionally simulated with the finite element method and compared with the corresponding results of the ferroelectric energy harvesters, where obvious advantages associated with the new strategy are demonstrated.

scholarly journals Integration of a soft dielectric composite into a cantilever beam for mechanical energy harvesting, comparison between capacitive and triboelectric transducers

2020 ◽  
Vol 10 (1) ◽  
Author(s):  
Mickaël Pruvost ◽  
Wilbert J. Smit ◽  
Cécile Monteux ◽  
Pablo Del Corro ◽  
Isabelle Dufour ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Cantilever Beam ◽  
Mechanical Energy ◽  
Wearable Electronics ◽  
Power Sources ◽  
Variable Capacitor ◽  
Energy Harvesters ◽  
External Bias ◽  
Intelligent Sensors ◽  
Dielectric Composite

AbstractFlexible dielectrics that harvest mechanical energy via electrostatic effects are excellent candidates as power sources for wearable electronics or autonomous sensors. The integration of a soft dielectric composite (polydimethylsiloxane PDMS-carbon black CB) into two mechanical energy harvesters is here presented. Both are based on a similar cantilever beam but work on different harvesting principles: variable capacitor and triboelectricity. We show that without an external bias the triboelectric beam harvests a net density power of 0.3 $$\upmu \mathrm{W}/{\mathrm{cm}}^{2}$$ μ W / cm 2 under a sinusoidal acceleration of 3.9g at 40 Hz. In a variable capacitor configuration, a bias of 0.15 $$\mathrm{V}/\upmu \mathrm{m}$$ V / μ m is required to get the same energy harvesting performance under the same working conditions. As variable capacitors’ harvesting performance are quadratically dependent on the applied bias, increasing the bias allows the system to harvest energy much more efficiently than the triboelectric one. The present results make CB/PDMS composites promising for autonomous portable multifunctional systems and intelligent sensors.

Piezoelectric Energy Harvesting from Floor Using Wounded PVDF Films

2014 ◽  
Vol 1030-1032 ◽  
pp. 3-7 ◽  
Author(s):  
E. Bischur ◽  
N. Schwesinger
Keyword(s):  
Energy Harvesting ◽  
Field Strength ◽  
Mechanical Energy ◽  
Wireless Systems ◽  
Process Step ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Sufficient Energy ◽  
Polarization Temperature ◽  
Electrical Loads

Energy harvesters of PVDF can be used to power small electrical loads or wireless sensor systems. Simple technologies are sufficient for the fabrication of these harvesting modules. Critical process step is the polarization of the piezoelectric material. Main piezoelectric parameters depend strongly on the polarization material. Particularly, the electric field strength and the polarization temperature influence the remanent polarization of PVDF. Dielectric breakdowns of the film at higher temperatures prevent a sufficient polarization. At least, all modules were polarized at a field strength of 100 – 120 MV/m and a temperature of 90°C.Modules with dimensions of 165mm x 95mm x 1.5mm were used to power a commercial available “development kit for Energy Harvesting Wireless systems” (EnOcean ‘EDK 300’). The modules possess of 20 layers of PVDF. Each module was connected via a standard four diode full rectifier bridge with the development kit EDK 300. Positioned underneath a parquet floor (thickness=10mm), the modules converted mechanical energy of footsteps into electricity. Goal of these investigations were to find out configurations suited to generate a sufficient energy level to supply the operation of the EDK 300. Two capacitors in the development kit are used to start the operation of the kit (C1=470μF) and to store converted energy (C2=0.25F). Already a few steps onto one module were sufficient to charge C1 and to start the operation of the EDK 300. Following steps (>100) produced energy which was stored in C2.

High and thermal-stable piezoelectricity in relaxor-based ferroelectrics for mechanical energy harvesting

2021 ◽  
Author(s):  
Xiaole Yu ◽  
Yudong Hou ◽  
Mupeng Zheng ◽  
Mankang Zhu
Keyword(s):  
Power Generation ◽  
Energy Harvesting ◽  
Mechanical Energy ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Generation Capacity ◽  
Thermal Stable

The utilization of relaxor-based ferroelectrics with high piezoelectricity is considered to be an effective way to enhance the power generation capacity of piezoelectric energy harvesters (PEHs). However, the severe depolarization...

scholarly journals Load Resistance Optimization of a Broadband Bistable Piezoelectric Energy Harvester for Primary Harmonic and Subharmonic Behaviors

2021 ◽  
Vol 13 (5) ◽  
pp. 2865 ◽  
Author(s):  
Sungryong Bae ◽  
Pilkee Kim
Keyword(s):  
Energy Harvester ◽  
Load Resistance ◽  
Oscillation Period ◽  
Ambient Vibration ◽  
Ambient Vibrations ◽  
Frequency Dependency ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Optimal Load ◽  
Bistable Energy Harvester

In this study, optimization of the external load resistance of a piezoelectric bistable energy harvester was performed for primary harmonic (period-1T) and subharmonic (period-3T) interwell motions. The analytical expression of the optimal load resistance was derived, based on the spectral analyses of the interwell motions, and evaluated. The analytical results are in excellent agreement with the numerical ones. A parametric study shows that the optimal load resistance depended on the forcing frequency, but not the intensity of the ambient vibration. Additionally, it was found that the optimal resistance for the period-3T interwell motion tended to be approximately three times larger than that for the period-1T interwell motion, which means that the optimal resistance was directly affected by the oscillation frequency (or oscillation period) of the motion rather than the forcing frequency. For broadband energy harvesting applications, the subharmonic interwell motion is also useful, in addition to the primary harmonic interwell motion. In designing such piezoelectric bistable energy harvesters, the frequency dependency of the optimal load resistance should be considered properly depending on ambient vibrations.

Sign in / Sign up

Export Citation Format

Share Document