The Influence of SiC Particles on Tool Wear in Machining of Al/SiC Metal Matrix Composites Produced by Powder Extrusion

2011 ◽  
Vol 325 ◽  
pp. 393-399 ◽  
Author(s):  
R. Yousefi ◽  
M.A. Kouchakzadeh ◽  
J. Rahiminasab ◽  
M.A. Kadivar
Keyword(s):  
Tool Wear ◽  
Metal Matrix Composites ◽  
Feed Rate ◽  
Metal Matrix ◽  
Cutting Speed ◽  
Test Method ◽  
Engineering Properties ◽  
Depth Of Cut ◽  
Matrix Composites ◽  
Sic Particles

Metal matrix composites (MMCs) have received considerable attention due to their excellent engineering properties. However, poor machinability has been the main deterrent to their substitution for metal parts. The hardness and abrasive nature of reinforcement phase causes rapid tool wear during machining which results in high machining costs. In this study, the effect of SiC particles (5, 15 & 20 percent) on tool wear in turning process is experimentally investigated. Continuous dry turning of Al/SiC particulate metal matrix composite produced by powder metallurgy and utilizing titanium carbide inserts has been achieved as the test method. The influence of machining parameters, e.g. cutting speed, feed rate and depth of cut on tool wear and cutting forces were investigated during the experiments. The results show that tool wear increases with increasing cutting speed, depth of cut and feed rate. The cutting speed and depth of cut are more dominant factors compared to feed rate on the tool wear. In addition, it is concluded that the flank wear increases with the increase of SiC percentage in the MMC.

Surface integrity in machining of AZ91/SiC composites

2021 ◽  
pp. 095440622110179
Author(s):  
A Asgari ◽  
M Sedighi
Keyword(s):  
Metal Matrix Composites ◽  
Surface Integrity ◽  
Metal Matrix ◽  
Cutting Speed ◽  
Weight Ratio ◽  
Depth Of Cut ◽  
Matrix Composites ◽  
Machined Surface ◽  
Sic Particles ◽  
Finished Surface

Use of metal matrix composites (MMC) is growing due to their high strength-to-weight ratio, resistance to wear, creep, etc. Machining of metal-matrix composites (MMC) faces many challenges, especially with regard to obtaining a finished surface with high quality. In this research, AZ91/SiC samples with different volume fractions are machined at different cutting conditions with respect to feed rate, cutting speed, and depth of cut. Surface integrity of the machined samples is analyzed by different methods such as tactile profilometer and 3D surface topography to investigate the SiC effects on the finished surface. Additionally, sample surfaces are evaluated by scanning electron microscope (SEM) and with energy-dispersive X-ray (EDS) to assess the surface defects formed around reinforcement materials. Results indicate SiC particles decline the surface quality and uniformity due to the formation of some defects such as micro cracks, holes, and undesired deformations when the cutting process. Also, subsurface SiC particles close to the machined surface are cracked after machining.

A Pressured Steam Jet Approach to Tool Wear Minimization in Cutting of Metal Matrix Composites

2007 ◽  
Vol 561-565 ◽  
pp. 643-646
Author(s):  
D. Anjaiah ◽  
Raviraj Shetty ◽  
R. Pai ◽  
M.V. Kini ◽  
S.S. Rao
Keyword(s):  
Tool Wear ◽  
Metal Matrix Composites ◽  
Metal Matrix ◽  
Experimental Testing ◽  
Cubic Boron Nitride ◽  
Polycrystalline Diamond ◽  
Experimental Tests ◽  
Depth Of Cut ◽  
Matrix Composites ◽  
The Matrix

Metal matrix composites (MMCs) have been found to possess tremendous prospective engineering applications that require materials offering a combination of lightweight with considerably enhanced mechanical and physical properties. However, the applications of MMCs are limited by their poor machinability which is a result of their highly abrasive nature that causes excessive wear to the cutting tools. In this study, an investigation into the mechanism of the tool wear in cutting of MMCs is carried out. It is found that during cutting of an MMC, the tool cutting edge will impact on the reinforcement particles. The impacted particles will then either be dislodged from the matrix, doing no harm to the tool, or be embedded into the matrix, ploughing on the tool flank and causing excessive tool flank wear. According to this tool wear mechanism, a pressured steam jet approach is developed for the minimization of the tool wear by preventing the impacted reinforcement particles from being embedded in the workpiece matrix. Experimental tests for cutting of SiC–aluminum MMC using cubic boron nitride (KB-90) and polycrystalline diamond (KP-300) tool inserts with the aid of the pressured steam jet are conducted. The results show that from full factorial design of experiments the effect of the pressured steam jet plays a significant role on the tool wear followed by tool inserts and depth of cut. The working mechanism of the pressured steam jet method and the experimental testing results are discussed in detail.

Tool Wear Analysis of Al 6061 Reinforced with 10 wt% Al2O3 Using High Hardened Inserts

2015 ◽  
Vol 787 ◽  
pp. 643-647
Author(s):  
M. Vignesh ◽  
K. Venkatesan ◽  
R. Ramanujam ◽  
Sundaravel Vijayan
Keyword(s):  
Tool Wear ◽  
Feed Rate ◽  
Metal Matrix ◽  
Cutting Speed ◽  
Stir Casting ◽  
Depth Of Cut ◽  
Machining Time ◽  
Al 6061 ◽  
Optimum Cutting ◽  
Coated Carbide

Metal matrix composites (MMC) are the combination of base metal matrix and reinforcing materials like SiC, Al2O3, etc. The present research is focused on the machinability studies of Al 6061 reinforced with 10% wtof Al2O3 particles using multi layered coated carbide inserts. Fabricated samples by stir casting route were turned by the most variable factors, cutting speed, depth of cutand by a constant feed rate of 0.206 mm/rev. Surface roughness and tool wear are considered asoutput. Experiments are conducted by varying the cutting speed while keeping feed rate and depth of cut as constant. After the optimum cutting speed was determined, the depth of cut is varied by keeping the cutting speedand feed rateas constant.Based on the optimum cutting speed (150 m/min), depth of cut (1.2 mm) and feed rate (0.206 mm/rev), a long run test was carried out to find out the tool life and surface finish. But due to the softness nature built up edge formation is obtained. At the optimal parametric combination, the built up edge obtained is less than 2 mm for a machining time of 425 s

Evaluation of the Surface Integrity when Machining LM6 Aluminum Metal Matrix Composites Using Coated and Uncoated Carbide Cutting Tools

2013 ◽  
Vol 465-466 ◽  
pp. 1049-1053 ◽  
Author(s):  
Abu Bakar Mohd Hadzley ◽  
Ahmad Siti Sarah ◽  
Raja Abdullah Raja Izamshah ◽  
Amran Ali Mohd ◽  
Mohd Shahir Kasim ◽  
...  
Keyword(s):  
Metal Matrix Composites ◽  
Surface Integrity ◽  
Feed Rate ◽  
Metal Matrix ◽  
End Milling ◽  
Cutting Tools ◽  
Depth Of Cut ◽  
Matrix Composites ◽  
Radial Depth ◽  
Coated Carbide

Metal matrix composite is composite material that combines the metallic properties of matrix alloys and additional element to reinforce the product. This paper evaluates the machining performance of uncoated carbide and coated carbide in terms of surface integrity during end milling of LM6 aluminium MMC. The parameter of cutting speed, feed rate and axial depth of cut were kept constant at 3000 rpm spindle speed, 60 mm/min feed rate and 0.5 axial dept of cut. The radial depth of cut were varied from 0.01mm to 0.1 mm. The results indicated that uncoated carbide show the better performance in terms of surface roughness and surface profile, as compared to coated carbide. On the other hand, coated carbide cutting tools suffered with built-up-edge formation at the tool edge, hence caused shearing effect and deterioration at the tool-chip interface. This study is expected to provide understanding of machining metal matrix composites based materials.

Effect of SiCp Reinforcement on Machinability of A356 Alloy Metal Matrix Composites

2016 ◽  
Vol 852 ◽  
pp. 142-148
Author(s):  
K. Jayakumar
Keyword(s):  
Surface Roughness ◽  
Metal Matrix Composites ◽  
Metal Matrix ◽  
End Milling ◽  
Cutting Speed ◽  
A356 Alloy ◽  
Experimental Result ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Matrix Composites

Machining of Aluminum Metal Matrix Composites (AMMCs) is a challenge for manufacturing industries due to their heterogeneous constituents which vary from soft matrix to hard reinforcements and their interfaces. To overcome the difficulties in machining of MMCs, researchers are continuously working to find the optimum process or machining parameters. In this work, End milling studies were carried out in A356 alloy powder-SiC particles (1 μm) in 0, 5, 10, 15 volume % reinforced AMMCs synthesised by vacuum hot pressing (VHP) route.The influence of machining parameters such as cutting speed, feed and depth of cut on the prepared composites in terms of surface roughness (Ra) and material removal rate (MRR) are measured from experimental study. Experiments were conducted as per Taguchi L16 orthogonal array with 4 factors and 4 levels.From the experimental result, it was identified that surface roughness varied from 0.214 μm to 4.115 μm and MRR varied from minimum of 1.11 cm3/min to maximum of 9.65 cm3/min. It is also observed that, MRR increased with increase in machining parameters and reinforcement quantity. Similarly, surface roughness decreased for increase of cutting speed, SiC particle (SiCp) reinforcement and increased for increase in feed and depth of cut. The optimum condition were observed in higher speed, lower feed and higher depth of cut on MMC with higher SiC content (15%) for getting higher machinability.

Study on Surface Roughness in Minimum Quantity Lubrication Turning of Al-6082/SiC Metal Matrix Composites

2019 ◽  
Vol 895 ◽  
pp. 127-133 ◽  
Author(s):  
C.J. Vishwas ◽  
M. Naik Gajanan ◽  
B. Sachin ◽  
Roy Abhinaba ◽  
N.P. Puneet ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Metal Matrix Composites ◽  
Feed Rate ◽  
Metal Matrix ◽  
Minimum Quantity Lubrication ◽  
Spindle Speed ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Matrix Composites ◽  
Minimum Quantity

Aluminum-based metal matrix composites (MMCs) have been suggested due to intense interest from automobile, marine, aerospace and other structural applications owing to their balanced mechanical, physical and chemical properties. MMCs are manufactured in order to meet present demand such as low material density, high mechanical strength and higher wear resistance of the component. Generally,MMCs tend to form rougher surface during machining because of the abrasive nature of hard ceramic particles present in them. Stir casting technique was used for fabrication of this composite which ensures better homogeneity.Furthermore, an attempt has been made in this paper to examine the results on the surface roughness of Al-6082/SiC metal matrix composites (containing 0%, 5% and 10% SiC particles).Focus was spent on parametric optimization of these composites in order to achieve cost-effective machining limits. The machining parameter studies have been carried out through the design of experiments (DoE) under minimum quantity lubrication (MQL) condition and effect of machining parameters such as spindle speed, feed rate and depth of cut on surface roughness was investigated to analyze the influence of reinforcement on surface roughness. In addition, analysis of variance was studied to obtain percentage contribution of machining parameters involved. Also, the surface morphology of the machined surface was studied through a scanning electron microscope (SEM). Distribution of SiC in aluminum alloy is fairly uniform with few clusters. Results of the experiments revealed that most significant turning parameter for surface roughness was spindle speed followed by feed rate and depth of cut. Furthermore, an optimal setting parameter for getting lower surface roughness was presented in confirmation table.

Studies on Mechanical and Machinability Properties of B4Cp Reinforced 6061Aluminum MMC Produced via Melt Stirring

2014 ◽  
Vol 592-594 ◽  
pp. 744-748 ◽  
Author(s):  
Vijaykumar Hiremath ◽  
S.T. Dundur ◽  
Raj L. Bharath ◽  
G.L. Rajesh ◽  
V. Auradi
Keyword(s):  
Boron Carbide ◽  
Metal Matrix Composites ◽  
Metal Matrix ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Matrix Composites ◽  
Mechanical And Physical Properties ◽  
Aluminum Metal Matrix Composites ◽  
Poly Crystalline Diamond

Aluminum boron carbide metal matrix composites (Al-MMC) have got wide applications in aeronautical and automobile industries due to their excellent mechanical and physical properties. Due to the presence of harder reinforcement particles, machining of these composites is a difficult task. The results of experimental investigation on mechanical and machinability properties of Boron carbide particle (B4Cp) reinforced aluminum metal matrix composites are presented in this paper.The influence of reinforced ratio of 7 wt% of B4Cpon mechanical properties was examined. It was observed that addition of B4Cpreinforcement resulted in improvement in hardness and tensile strengths to the extent of 71% and 38.4% respectively. Fabricated samples were turned on medium duty lathe of 3 kW spidle power with Poly crystalline diamond tool (PCD) of 10 μm particle size at various cutting conditions. The effect of machining parameters, e.g. cutting speed, feed rate and depth of cut on cutting forces and formation of BUE was studied.

scholarly journals Machinability study of Al-TiC metal matrix composite

2018 ◽  
Vol 144 ◽  
pp. 03001 ◽  
Author(s):  
P. N. Siddappa ◽  
B. P. Shivakumar ◽  
K. B. Yogesha ◽  
M. Mruthunjaya ◽  
M. B. Hanamantraygouda
Keyword(s):  
Mechanical Properties ◽  
Feed Rate ◽  
Metal Matrix ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Stir Casting ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Matrix Composites ◽  
Casting Technique

Aluminum Metal Matrix Composites have emerged as an advanced class of structural materials have a combination of different, superior properties compared to an unreinforced matrix, which can result in a number of service benefits such as increased strength, higher elastic moduli, higher service temperature, low CTE, improved wear resistance, high toughness, etc. The excellent mechanical properties of these materials together with weight saving makes them very attractive for a variety of engineering applications in aerospace, automotive, electronic industries, etc. Hence, these materials provide as alternative substitutes for conventional engineering materials when specific mechanical properties necessary for required applications. In this work an attempt is made to study the machining parameters of Al6061/TiC MMC. The composite is developed by reinforcing TiC particles in varying proportions of 3, 6, 9 and 12 % weight fractions to the Al6061 matric alloy through stir casting technique. Cutting forces were measured by varying cutting speed and feed rate with constant depth of cut for different % weight fractions. The results showed that the cutting force increases with the increase of feed rate and decreases with the increase of cutting speed for all the weight fractions. Cutting parameters were optimized using Taguchi technique.

Optimization of machining parameters using WASPAS and MOORA

2019 ◽  
Vol 17 (2) ◽  
pp. 237-246 ◽  
Author(s):  
Venkateshwar Reddy Pathapalli ◽  
Veerabhadra Reddy Basam ◽  
Suresh Kumar Gudimetta ◽  
Madhava Reddy Koppula
Keyword(s):  
Metal Matrix Composites ◽  
Metal Matrix ◽  
Metal Cutting ◽  
Optimal Parameter ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Matrix Composites ◽  
Content Type ◽  
Composite Samples

Purpose Nowadays, the applications of metal matrix composites are tremendously increasing in engineering fields. Consequently, the demand for precise machining of composites has also grown enormously. The purpose of this paper is to reduce production cost and simultaneously improve desired product quality through optimal parameter setting using WASPAS and MOORA. Design/methodology/approach Metal matrix composites were fabricated using stir casting process, with aluminum 6063 as matrix and titanium carbide as reinforcement. Fabricated composite samples were machined on medium duty lathe using cemented carbide tool. All the experiments were carried out based on Box–Behnken design. Comparison of multi objective optimization based on ratio analysis and weighted aggregated sum product assessment in optimizing four parameters, namely, “cutting speed,” “feed rate,” “depth of cut” and “reinforcement weight percent of composite samples”; evaluating their influence on material removal rate, cutting force and surface roughness were carried out. Findings The output achieved by both MOORA and WASPAS are in similar MCDM) techniques in the selection of machining parameters. Practical implications The results obtained in the present paper will be helpful for decision makers in manufacturing industries, who work in metal cutting area, to select the suitable levels for the parameters by implementing the MCDM techniques. Originality/value The novelty of this paper is making an attempt to select better MCDM technique based on the comparison of results obtained for the individual technique.

Tool Wear in High Speed Milling of SiCp/Al2024 Metal Matrix Composites

2010 ◽  
Vol 33 ◽  
pp. 200-203 ◽  
Author(s):  
Y.J. Wang ◽  
Ming Zhou ◽  
S.N. Huang ◽  
Y.J. Zhang
Keyword(s):  
Tool Wear ◽  
Metal Matrix Composites ◽  
Metal Matrix ◽  
High Speed ◽  
Flank Wear ◽  
Cutting Speed ◽  
Dominant Factor ◽  
Matrix Composites ◽  
High Speed Milling ◽  
Coated Tools

This paper presents an experimental study in high speed milling of metal matrix composites (MMCs). Machining tests were carried out on a high speed milling machine by using TiAlN coated tools and chemical vapour deposition (CVD) diamond coated tools. The cutting tool wear was investigated using an optical microscope and a scanning electron microscope (SEM). The experimental results showed that flank wear is the dominant tool wear mode and abrasive wear and adhesive wear appears to be the main wear mechanism. The build-up edge (BUE) exists during the machining process at a certain speeds. Cutting speed is a dominant factor affecting the flank wear. Generally, high cutting speed lead to severe tool wear, but there seemed to be a certain cutting speed which will cause the least tool wear. Furthermore, there exists a cutting speed limit for both TiAlN coated tools and CVD coated diamond tools in high speed milling of MMCs, beyond which the edge chipping will cause the tool failure very soon.

Sign in / Sign up

Export Citation Format

Share Document