Treatment of Printing and Dyeing Wastewater by the Iron Scurf and Flue Dust Internal Electrolysis Method

2011 ◽  
Vol 415-417 ◽  
pp. 438-441
Author(s):  
Jin Xia Yan ◽  
Dong Fang Li ◽  
Shao Feng Dong
Keyword(s):  
Reaction Time ◽  
Electric Conductivity ◽  
Removal Rate ◽  
Dyeing Wastewater ◽  
Optimum Conditions ◽  
Printing And Dyeing Wastewater ◽  
Flue Dust ◽  
Internal Electrolysis ◽  
Electrolysis Method ◽  
Cod Removal Rate

The printing and dyeing wastewater was treated by internal electrolysis method. The results show the chromaticity removal rate was up to 98.53 percent and COD removal rate 85.98 percent under the optimum conditions of wastewater pH 4, reaction time 30 minutes, the electric conductivity 1450μm/cm, the value BOD5/COD increases from 0.34 to 0.51. Moreover, the pH, Fe2+ concentration and absorbance of wastewater changed in the process, the mechanism of that was also analyzed.

Study on Treatment of M-Cresol Wastewater Using Potassium Ferrate(VI)

2012 ◽  
Vol 610-613 ◽  
pp. 2367-2371 ◽  
Author(s):  
Ming Zhong Hu ◽  
Zhen He Shi ◽  
Hong Yan Zhao
Keyword(s):  
Reaction Time ◽  
Ph Value ◽  
Removal Rate ◽  
Cod Removal ◽  
Potassium Ferrate ◽  
Optimum Conditions ◽  
Initial Concentration ◽  
Cod Removal Rate

The effects of the oxidation of potassium ferrate and the flocculation on cresol wastewater water were evaluated. This research aimed at determining the optimum conditions for the COD removal rate duing cresol wastewater water process. The results showed that potassium ferrate dosage of 1.1g/L, the pH value of 5, reaction time 15min, m-cresol initial concentration of 200 mg/L were the optimum conditions. Under the optimum conditions, COD removal rate was over 67%.

Study on the Advanced Treatment of Dyeing Wastewater by Photocatalytic-H2O2

2014 ◽  
Vol 1048 ◽  
pp. 503-506
Author(s):  
Hui Xia Lan ◽  
Ping Ma ◽  
Jian Zhang ◽  
Hui Jie Li ◽  
Heng Zhang ◽  
...  
Keyword(s):  
Wastewater Treatment ◽  
Reaction Time ◽  
Removal Rate ◽  
Cod Removal ◽  
Advanced Treatment ◽  
Dyeing Wastewater ◽  
Biochemical Treatment ◽  
Emission Standard ◽  
Effect Of Ph ◽  
Cod Removal Rate

The composition of dyeing wastewater is complicated, after biochemical treatment, the effluent COD is still unable to meet the emission standard. To achieve discharge standard that often require advanced treatment after biochemical. This paper investigated effect of pH, reaction time, ZnO dosage, dosage of H2O2on the effect of dyeing wastewater treatment by photocatalytic-H2O2, the results showed that the reaction time of 15 min, pH of 4, dosage of ZnO was 4 g/L, 30% H2O2dosage was 1 ml/L, the COD removal rate was highest, can reach more than 55%.

scholarly journals Pretreatment of printing and dyeing wastewater by Fe/C micro-electrolysis combined with H2O2 process

2018 ◽  
Vol 2017 (3) ◽  
pp. 707-717 ◽  
Author(s):  
Yan Wang ◽  
Xianwei Wu ◽  
Ju Yi ◽  
Lijun Chen ◽  
Tianxiang Lan ◽  
...  
Keyword(s):  
Removal Rate ◽  
Oxygen Demand ◽  
Cod Removal ◽  
Coefficient Of Determination ◽  
H2o2 Concentration ◽  
Dyeing Wastewater ◽  
Spectra Analysis ◽  
Printing And Dyeing Wastewater ◽  
Initial Ph ◽  
Cod Removal Rate

Abstract A novel iron-carbon (Fe/C) micro-electrolysis combined with H2O2 (ICMH) process was proposed to pretreat the printing and dyeing wastewater (PDW), using a micro-electrolysis filling. The effects of H2O2 concentration, reaction time, initial pH, and Fe/C dosage on chemical oxygen demand (COD) removal rate of PDW were optimized by response surface methodology (RSM). The maximum COD removal rate was approximately 77.65% after 186 min treatment, when the concentration of H2O2, initial pH and the dosage of Fe/C were 8.88 g/L, 1.5 and 837 g/L, respectively. Analysis of variance (ANOVA) showed a high coefficient of determination value (R2 = 0.9780). And H2O2 concentration and initial pH were the key factors to improve the treatment effect. UV-Vis spectra indicated that a significant blue shift at 220 nm, attributing that fused aromatic hydrocarbons were degraded effectively. 3D-EEM spectra analysis showed that the water samples of PDW mainly contained three kinds of organic matter: refractory fulvic acid, soluble microbial metabolites and aromatic proteins, and the degradation rate of these was 81.76%, 53.78% and 70.83%, respectively.

Study on Iron Filings Combined with Biological Carbon Derived from Chicken Manure Forming Internal Electrolysis to Treat Dyeing Wastewater of Disperse Blue E-4R

2014 ◽  
Vol 955-959 ◽  
pp. 2205-2211
Author(s):  
Jian Ping Li
Keyword(s):  
Particle Size ◽  
Reaction Time ◽  
Removal Rate ◽  
Aeration Rate ◽  
Chicken Manure ◽  
Liquid Volume ◽  
Mass Ratio ◽  
Dyeing Wastewater ◽  
Internal Electrolysis ◽  
Circulation Velocity

Aiming at the difficulty of treating dyeing wastewater, the limitation of the traditional electrolysis method, the high cost of active carbon and the environmental pollution of the chicken manure in farms, the paper put forward a new method of using iron combined with biological carbon derived from chicken manure forming internal electrolysis to treat dyeing wastewater. It discussed the effects of mass ratio of iron and biological carbon derived from chicken manure, pH, reaction time, the particle size of iron filings, the aeration rate, circulation velocity and the circling liquid volume on the removal rate of the organic matter in wastewater. The result showed that iron combined with biological carbon derived from chicken manure forming internal electrolysis to treat dyeing wastewater could "using waste to treat waste" and the effect was better. The removal rate of COD was over 85% and the decolorization rate was over 95% when the mass ratio of iron and biological carbon derived from chicken manure was 1:1, the PH was 6, reaction time was was 60min, the particle size of iron filings was 0.9~2.0mm, the aeration rate was 10mL/min, circulation velocity was 50r/min and the circling liquid volume was 2000mL.

Study on Pretreatment of Dye Wastewater by Fenton Oxidation Process

2012 ◽  
Vol 627 ◽  
pp. 378-381
Author(s):  
Bi Rong Wang
Keyword(s):  
Reaction Time ◽  
Oxidation Process ◽  
Removal Rate ◽  
Fenton Oxidation ◽  
Dye Wastewater ◽  
Dyeing Wastewater ◽  
Reaction Conditions ◽  
Fenton Oxidation Process

Fenton pretreatment has been used for treating dye wastewater. The effects of the dos of H2O2 and FeSO4, reaction time and pH on the removal COD were investigated. It was found that, when the reaction conditions are as follows: COD 2850 mg/L dyeing wastewater, the dosage of H2O2 is 140mmol/L, FeSO4 17.02 mmol/L, pH 7.6, and reaction time 1.0 h, the CODcr of dye wastewater removal rate of up to 70%. Fenton pretreatment process of dye wastewater has a broad prospect.

Comparison of Degradation and Decoloration on Cigarette Industry Wastewater by Ozone and Advanced Oxidation

2013 ◽  
Vol 295-298 ◽  
pp. 1168-1172
Author(s):  
Jing Shi Li ◽  
Xiao Jun Wang ◽  
Rui Deng ◽  
Zhi Hua Pang
Keyword(s):  
Reaction Time ◽  
Removal Rate ◽  
Advanced Oxidation ◽  
Simple Operation ◽  
Cigarette Industry ◽  
Optimum Parameters ◽  
Cod Removal Rate ◽  
Decoloration Rate ◽  
Operation Cost ◽  
Industry Wastewater

Chromaticity of cigarette industry wastewater increase when treating by aerobic due to large quantities of lignin, nicotine and carbohydrate. Ozone and advance oxidation are proposed for degradation and decoloration of cigarette wastewater that processed by aerobic. The result shows that ozone process has its advantage of high decoloration rate, simple operation and low operation cost. Optimum parameters of ozone process are ozone dosage of 37.65mg/L, reaction time of 15min, reaction pH of 7.0-9.0. The COD removal rate is 38.3% when the decoloration rate is 57.5%. Operation cost of ozone process is 0.4 yuan/m3.

Synergetic Degradation of Zidovudine Wastewater by Ultrasonic and Iron-Carbon Micro-Electrolysis

2011 ◽  
Vol 347-353 ◽  
pp. 1949-1952 ◽  
Author(s):  
Liang Li ◽  
Bing Zhe Xu ◽  
Chang Yu Lin ◽  
Xiao Min Hu
Keyword(s):  
Reaction Time ◽  
Degradation Rate ◽  
Removal Rate ◽  
Cod Removal ◽  
Mass Ratio ◽  
Initial Ph ◽  
Cod Removal Rate

Zidovudine wastewater is difficult to biodegradation due to high COD and toxicity. The synergetic treatment of Zidovudine wastewater by Ultrasonic and iron-carbon micro-electrolysis technology was studied. The influence of initial pH, reaction time, mass ratio of iron and carbon and mass ratio of iron and water on degradation rate of COD was researched. The result showed that the COD removal rate was only about 54.3% and the degradation speed is very slow when iron-carbon micro-electrolysis treated Zidovudine wastewater　separately. However, when ultrasonic synergy micro-electrolysis to treat Zidovudine wastewater, the COD removal rate could was up to 85% and the reaction time was also decreased. Moreover, the BOD5 / COD rose from 0.15 to 0.35, which meant the wastewater became easily biodegradable.

Study on the Advanced Treatment of Printing and Dyeing Wastewater by Fenton Oxidation

2014 ◽  
Vol 1010-1012 ◽  
pp. 805-808
Author(s):  
Xiu Wen Wu ◽  
Ping Ma ◽  
Hui Xia Lan ◽  
Heng Zhang ◽  
Shan Hong Lan
Keyword(s):  
Reaction Time ◽  
Removal Efficiency ◽  
Treatment Effect ◽  
Cod Removal ◽  
Fenton Oxidation ◽  
Advanced Treatment ◽  
Dyeing Wastewater ◽  
Printing And Dyeing Wastewater ◽  
Cod Removal Efficiency

The influence of H2O2、addition of Fe2+、pH、reaction time and temperature to advanced treatment effect of printing and dyeing wastewater with Fenton oxidation was studied. The results showed that when the addition of H2O2(the concentration was 30%) was 3mL/L,the addition of FeSO4·7H2O was 1.6g/L,pH was 4,the temperature was about 30°C,reacting time was 35min,the COD removal efficiency achieved above 55%,COD of effluent was below 45mg/L.

Advanced Treatment of Ship Sewage by Fenton-Oxidation Process

2014 ◽  
Vol 1010-1012 ◽  
pp. 595-598
Author(s):  
Gui Fang Liu ◽  
Hong Mei Yan ◽  
Yuan Gao ◽  
Ya Quan Sun ◽  
Yu Ping Zhang
Keyword(s):  
Water Quality ◽  
Reaction Time ◽  
Optimum Condition ◽  
Oxidation Process ◽  
Removal Rate ◽  
Quality Standard ◽  
Fenton Oxidation ◽  
Domestic Water ◽  
Cod Removal Rate ◽  
Fenton Oxidation Process

Fenton-oxidation process was used to treat the simulation ship sewage that had met the requirement of IMO discharge standard. The effects of reaction time, doses of H2O2 and FeSO4, pH and temperature on COD removal rate were investigated. The results showed that the optimum condition for treating simulation ship sewage was as follows: pH=3.0, concentration of H2O2=9 mmol/L, concentration of FeSO4=3 mmol/L, and reaction time=30 min. Under the optimum condition, the removal rate of COD was to 62.7%. The water quality of the effluent could meet Miscellaneous Domestic Water Quality Standard.

Catalytic Oxidation of 4,4'-Dibromobiphenyl in Sub-Critical Water with Mn0.9-Co0.1-Ce-Oxide

2011 ◽  
Vol 282-283 ◽  
pp. 13-16
Author(s):  
Jin Yang Chen ◽  
Ru Yi Ruan ◽  
Zhi Li
Keyword(s):  
Activation Energy ◽  
Reaction Time ◽  
Apparent Activation Energy ◽  
Hydrothermal Method ◽  
Subcritical Water ◽  
Degradation Kinetics ◽  
Removal Rate ◽  
Oxidative Degradation ◽  
Cod Removal Rate ◽  
Co Precipitation

A complex mental oxide Mn0.9-Co0.1-Ce-oxide was prepared by co-precipitation-hydrothermal method and it was used as catalyst to oxidative degradation of 4,4- dibromobiphenyl (4,4’-DBB) in subcritical water. The optimization conditions is obtained as follows: 5% Mn0.9-Co0.1-Ce-oxidecatalyst, m(H2O2):m(4,4’-DBB)=200:1,temperature of 613K, reaction time of 20 minutes, and COD removal rate is more than 99 %. In the temperature range of 603–633 K, the degradation kinetics is studied and apparent activation energy is 35.92 and 46.69 kJ/mol for no catalyst and 5% Mn0.9-Co0.1-Ce-oxide, respectively.

Sign in / Sign up

Export Citation Format

Share Document