Design of Electronic Control System of High-Grade Textile Machine Based on CAN Bus

2012 ◽  
Vol 503-504 ◽  
pp. 1580-1583
Author(s):  
Hui Shan Yu ◽  
Shou Hui Zhang ◽  
Xiao Kua Ji ◽  
Xin Jian Liu
Keyword(s):  
Control System ◽  
Can Bus ◽  
Fast Response ◽  
High Grade ◽  
Electronic Control ◽  
Accuracy Control ◽  
Operating Personnel ◽  
Electronic Control System ◽  
Textile Machine ◽  
Low Efficiency

According to some problems of Low efficiency of the current domestic Textile Machine，Reliability is bad，The operating personnel labor intensity，A single product varieties and so on. Design of electronic control system of high-grade textile machine based on CAN Bus. The system with RENESAS SH7047 chips as the controller chip, Realize the all of the interrupt signal, sensor signal detection, fuzzy PID algorithm and main shaft encoder location, Through the CAN bus transmission way to complete accuracy control ac servo system. The actual operation commissioning proves the electronic control system has the fast response, and robust, more kinds of textile and so on.

The Design and Simulation of Vehicle Electronic Control Network Based on CAN/LIN Bus

2011 ◽  
Vol 403-408 ◽  
pp. 3044-3048
Author(s):  
Wen Chang Lu ◽  
Pei Ying Lu ◽  
Chen Long ◽  
Ruo Chen Wang
Keyword(s):  
Control System ◽  
Can Bus ◽  
Peak Load ◽  
Control Network ◽  
Electronic Control ◽  
Message Scheduling ◽  
Electronic Control System ◽  
Lin Bus ◽  
Load Peak ◽  
Delayed Time

A CAN/LIN bus-based distributed vehicle electronic control system is designed and nodes of the control system are defined in this paper. The simulation of system designed is completed by Vector CANoe, which gives the results of bus load, peak load and the delayed time that transmitted on CAN bus. The sequence of message scheduling and the interval of message transmitted on LIN bus are also listed to show the reliability of CAN/LIN bus-based distributed vehicle electronic control system.

Modeling and Simulation of an Automotive Body Electronic Control System

2013 ◽  
Vol 278-280 ◽  
pp. 1754-1757
Author(s):  
Xiu Ting Wu ◽  
Xiao Feng Yin ◽  
Xiao Hua Wu ◽  
Qi Chang Yang
Keyword(s):  
Control System ◽  
Can Bus ◽  
Electronic Control ◽  
Functional Requirements ◽  
Application Layer ◽  
Wiring Harness ◽  
Automotive Body ◽  
Electronic Control System ◽  
Door Lock ◽  
Simulation Results

To simplify the wiring harness of automotive body control system, the functional requirements of automotive door locks, window lifters, rearview mirrors, trunk lock, and lights were analyzed, and an architecture of automotive body electronic control system was put forward based on CAN bus technology. The application layer protocol referring SAE J1939 protocol specification was defined. And the door lock system was modeled and simulated as an example by using CANoe. The simulation results show that the proposed architecture of automotive body electronic control system works well, and the reliability of automotive body control system can be improved and the automotive weight and cost can be reduced.

scholarly journals Recoverable autonomous sonde for subglacial lake exploration: electronic control system design

2021 ◽  
pp. 1-17
Author(s):  
Shilin Peng ◽  
Xiao Jiang ◽  
Yongzhen Tang ◽  
Chong Li ◽  
Xiaodong Li ◽  
...  
Keyword(s):  
Control System ◽  
System Design ◽  
Video Recording ◽  
Control System Design ◽  
Electronic Control ◽  
High Definition ◽  
Water Conductivity ◽  
Camera System ◽  
Subglacial Lake ◽  
Electronic Control System

Abstract Subglacial lake exploration is of great interest to the science community. RECoverable Autonomous Sonde (RECAS) provides an exploration tool to measure and sample subglacial lake environments while the subglacial lake remains isolated from the glacier surface and atmosphere. This paper presents an electronic control system design of 200 m prototype of RECAS. The proposed electronic control system consists of a surface system, a downhole control system, and a power transfer and communication system. The downhole control system is the core element of RECAS, and is responsible for sonde status monitoring, sonde motion control, subglacial water sampling and in situ analysis. A custom RS485 temperature sensor was developed to cater for the limited size and depth requirements of the system. We adopted a humidity-based measurement to monitor for a housing leak. This condition is because standard leak detection monitoring of water conductivity may be inapplicable to pure ice in Antarctica. A water sampler control board was designed to control the samplers and monitor the on/off state. A high-definition camera system with built-in storage and self-heating ability was designed to perform the video recording in the subglacial lake. The proposed electronic control system is proven effective after a series of tests.

scholarly journals Design and Test Evaluation of Full Authority Digital Electronic Control System for an Auxiliary Power Unit

2018 ◽  
Vol 36 (6) ◽  
pp. 1102-1107
Author(s):  
Kai Peng ◽  
Fan Yang ◽  
Ding Fan ◽  
Linfeng Gou ◽  
Hongliang Xiao ◽  
...  
Keyword(s):  
Control System ◽  
Power Unit ◽  
Digital Control ◽  
Electronic Control ◽  
Digital Control System ◽  
Control Laws ◽  
Auxiliary Power Unit ◽  
Auxiliary Power ◽  
Electronic Control System ◽  
Key Techniques

A helicopter auxiliary power unit (APU) is initially equipped with a hydro-mechanical control system (HMC). Because HMC's complex structure is difficult to be modified to realize sophisticated control algorithms and the APU is faced with the need for performance improvement, it is urgently necessary to carry out digital control modification of HMC. Based on the analysis of control laws of the original HMC and differences between HMC and digital control system, key techniques involved in the digital control system are studied, such as overall structure, control laws and fuel system based on electric fuel pump, and finally a full authority digital electronic control system (FADEC) is developed for APU. Functions, performances and key techniques of the FADEC system are evaluated on test rig, and the test results show functions of original control system are enhanced and performances of APU are improved more effectively under the control of the designed FADEC compared with the original HMC.

Hybrid Magnetic/Foil Bearing System for an Oil-Free Thrust Bearing Test Rig

2001 ◽  
Author(s):  
Thomas E. Russell ◽  
Crystal Heshmat ◽  
Dennis Locke
Keyword(s):  
Magnetic Material ◽  
Control System ◽  
Thrust Bearing ◽  
Material Selection ◽  
System Stability ◽  
Electronic Control ◽  
Test Rig ◽  
Foil Bearing ◽  
Electronic Control System ◽  
Foil Thrust Bearing

A novel, high-speed, high temperature, oil-free, foil thrust bearing test rig has been developed with a critical element being a double-acting, active magnetic thrust bearing. The magnetic thrust bearing is used to react against loads applied to the foil thrust bearing under test. The magnetic bearing has the capability of reacting against thrust loads of up to 2224 N (500 pounds) at speeds to 80,000 rpm, while the rotor is supported by foil journal bearings. Two issues that are especially challenging for this test rig are magnetic material selection and the electronic control system. The magnetic material selection is critical due to the high centrifugal stresses that occur at 80,000 rpm. The electronic control system must handle the non-linear variation in stiffness and damping that is seen by the magnetic thrust bearing as the foil thrust bearing is loaded, as well as maintain rotor system stability as the foil bearing is purposefully overloaded to the point of failure to discover maximum load and performance capabilities. This paper describes the design of the active magnetic thrust bearing, the material selection process, and the development of a digital signal processor based control system. Typical experimental data obtained during operation of the test rig will also be presented.

Sign in / Sign up

Export Citation Format

Share Document