Factor Affecting Corrosion Behavior of Weldment of S30400 Stainless Steel in Cold Region

2012 ◽  
Vol 586 ◽  
pp. 247-253
Author(s):  
Tsuyoshi Takahashi ◽  
Yoshitaka Iwabuchi ◽  
Kazunori Ishitsuka
Keyword(s):  
Residual Stress ◽  
Corrosion Behavior ◽  
Stainless Steels ◽  
Isothermal Condition ◽  
Corrosion Damage ◽  
Immersion Test ◽  
Cold Region ◽  
Freeze Thaw ◽  
Damaged Zone ◽  
High Residual Stress

The influence of residual stress and sensitizing on the electrochemical and corrosion behavior of type SUS304 stainless steels weldment has been studied in the Freeze-Thaw condition. After immersion test at Freeze-Thaw cyclic condition the severe corrosion damage was detected in the vicinity of weld boundary more than isothermal condition. The corrosion damaged zone corresponds to the location in which there are high residual stress and sensitization. The influence of residual stress and sensitization was distinguished and its magnitude was evaluated by voltammetry method.

Optimization Research of Mix Proportion of Frost Resistance Construction of Concrete Based on the MATLAB Language

2014 ◽  
Vol 584-586 ◽  
pp. 1917-1921
Author(s):  
Jun Jie Zhang ◽  
Rui Hong Shao ◽  
Xiang Yi Meng
Keyword(s):  
Compressive Strength ◽  
Objective Function ◽  
Frost Resistance ◽  
Unit Volume ◽  
Influence Factors ◽  
Multi Objective Optimization ◽  
Cold Region ◽  
Freeze Thaw ◽  
Performance Indexes ◽  
Mix Proportion

Analyze the influence factors of mix proportion affecting concrete freeze-thaw damage. Use the five main performance indexes of the concrete, which are compressive strength, strength of extension, impermeability grade, and frost resistance grade and per unit volume cost concrete, as the objective function of multi-objective optimization equation. Invoke the fgoalattain function in the MATLAB Optimization Toolbox to solve. The optimized parameters of mix proportion of frost resistance construction of unit concrete in cold region are: concrete 1532.6kg, water 910kg, sand 5510.6kg, 5-20mm cobblestone 3747.2kg、20-40mm cobblestone 3658.6kg、40-80mm cobblestone 4733.5kg、80-150mm cobblestone 4738.1kg, and the dosage of water reducing agent is 7.3kg.

scholarly journals Crevice Corrosion Behavior of Nitrogen Bearing Austenitic Stainless Steels

1999 ◽  
Vol 48 (3) ◽  
pp. 169-175 ◽  
Author(s):  
Alberto A. Ono ◽  
Tadashi Shinohara ◽  
Shigeo Tsujikawa
Keyword(s):  
Corrosion Behavior ◽  
Stainless Steels ◽  
Crevice Corrosion ◽  
Austenitic Stainless Steels

Corrosion behavior of vacuum sintered duplex stainless steels

2007 ◽  
Vol 191 (1-3) ◽  
pp. 161-164 ◽  
Author(s):  
L.A. Dobrzański ◽  
Z. Brytan ◽  
M. Actis Grande ◽  
M. Rosso
Keyword(s):  
Corrosion Behavior ◽  
Stainless Steels ◽  
Duplex Stainless Steels

scholarly journals Fluoride Treatment and In Vitro Corrosion Behavior of Mg-Nd-Y-Zn-Zr Alloys Type

Materials ◽  
2022 ◽  
Vol 15 (2) ◽  
pp. 566
Author(s):  
Pham Hong Quan ◽  
Iulian Antoniac ◽  
Florin Miculescu ◽  
Aurora Antoniac ◽  
Veronica Manescu (Păltânea) ◽  
...  
Keyword(s):  
Corrosion Behavior ◽  
Orthopedic Implants ◽  
Immersion Test ◽  
Nacl Solution ◽  
Fluoride Ions ◽  
Fluoride Treatment ◽  
Cardiovascular Stents ◽  
Before And After

Fluoride conversion coatings on Mg present many advantages, among which one can find the reduction of the corrosion rate under “in vivo” or “in vitro” conditions and the promotion of the calcium phosphate deposition. Moreover, the fluoride ions released from MgF2 do not present cytotoxic effects and inhibit the biofilm formation, and thus these treated alloys are very suitable for cardiovascular stents and biodegradable orthopedic implants. In this paper, the biodegradation behavior of four new magnesium biodegradable alloys that have been developed in the laboratory conditions, before and after surface modifications by fluoride conversion (and sandblasting) coatings, are analyzed. We performed structural and surface analysis (XRD, SEM, contact angle) before and after applying different surface treatments. Furthermore, we studied the electrochemical behavior and biodegradation of all experimental samples after immersion test performed in NaCl solution. For a better evaluation, we also used LM and SEM for evaluation of the corroded samples after immersion test. The results showed an improved corrosion resistance for HF treated alloy in the NaCl solution. The chemical composition, uniformity, thickness and stability of the layers generated on the surface of the alloys significantly influence their corrosion behavior. Our study reveals that HF treatment is a beneficial way to improve the biofunctional properties required for the studied magnesium alloys to be used as biomaterials for manufacturing the orthopedic implants.

scholarly journals Effect of Shot Peening Treatment on Residual Stress and Magnetic Barkhausen Noise of AISI 201LN and AISI 304L Stainless Steels

2022 ◽  
Vol 25 ◽  
Author(s):  
Marcel Freitas de Souza ◽  
Juan Manuel Pardal ◽  
Hugo Ribeiro da Igreja ◽  
Linilson Rodrigues Padovese ◽  
Maria Cindra Fonseca
Keyword(s):  
Residual Stress ◽  
Stainless Steels ◽  
Shot Peening ◽  
Barkhausen Noise ◽  
Magnetic Barkhausen Noise ◽  
Aisi 304L
Sign in / Sign up

Export Citation Format

Share Document