Mechanical Properties of Sandstone under Loading and Unloading Conditions

2014 ◽  
Vol 852 ◽  
pp. 441-446 ◽  
Author(s):  
Xing Xia Wang ◽  
Wen Juan Ma ◽  
Jian Wen Huang ◽  
Zai Yi Liao
Keyword(s):  
Mechanical Properties ◽  
Triaxial Compression ◽  
Deformation Modulus ◽  
Confining Pressure ◽  
Rock Deformation ◽  
Test Results ◽  
Compression Tests ◽  
Triaxial Compressive Strength ◽  
Unloading Confining Pressure ◽  
Triaxial Compression Tests

The mechanical properties of rock mass under unloading conditions are essentially different from that under loading conditions. Triaxial compression tests and unloading confining pressure tests are conducted, and test results show that unloading failure is more brittle, and rock samples suffer more damage under unloading failure. The larger the initial confining pressure is, the easier of unloading failure is occurred. The increasing or decreasing values of rock deformation modulus under unloading conditions are within 10% of rock triaxial compressive strength. Unloading failure leads to deterioration of rock deformation modulus, which decreases gradually with confining pressure decreasing, and the decrease rates get bigger and bigger with unloading ratio of confining pressure increasing. Deformation modulus is only 24-34% of that under loading condition when rock strength goes down to residual strength.

Behaviors of Xiashu Loess in the Lower Reaches of China’s Yangtze River under Triaxial Compression and the Microscopic Explanations

2016 ◽  
Vol 858 ◽  
pp. 91-97
Author(s):  
Jun Hua Xiao ◽  
Wen Qi Zheng
Keyword(s):  
Mechanical Properties ◽  
Yangtze River ◽  
Shear Failure ◽  
Triaxial Compression ◽  
Processing Technique ◽  
Point Of View ◽  
Image Processing Technique ◽  
Test Results ◽  
Compression Tests ◽  
Triaxial Compression Tests

To investigate the macroscopic mechanical properties of undisturbed structural Xiashu loess in the lower reaches of China’s Yangtze River under triaxial compression, and obtain the intrinsic explanations for the macroscopic mechanical properties from the microscopic point of view, in laboratory, triaxial compression tests were carried out, microstructure images of sheared samples were collected by scanning electron microscope (SEM), and quantitative parameters of microstructure (mainly about particle or pore size, distribution, and alignment) were extracted by digital image processing technique. Based on the test results, the deviator stress-strain relationships of both undisturbed and remoulded Xiashu loess, the structural strength, and the microstructural evolution mechanism about the formation of shear failure zone of Xiashu loess under triaxial compression were analyzed.

scholarly journals Triaxial Testing of Geosynthetics Reinforced Tailings with Different Reinforced Layers

Materials ◽  
2020 ◽  
Vol 13 (8) ◽  
pp. 1943
Author(s):  
Fu Yi ◽  
Changbo Du
Keyword(s):  
Triaxial Compression ◽  
Friction Angle ◽  
Confining Pressure ◽  
Test Results ◽  
Compression Tests ◽  
Strength Index ◽  
Stress Strain ◽  
High Confining Pressure ◽  
Zhang Model ◽  
Triaxial Compression Tests

To evaluate the shear properties of geotextile-reinforced tailings, triaxial compression tests were performed on geogrids and geotextiles with zero, one, two, and four reinforced layers. The stress–strain characteristics and reinforcement effects of the reinforced tailings with different layers were analyzed. According to the test results, the geogrid stress–strain curves show hardening characteristics, whereas the geotextile stress–strain curves have strain-softening properties. With more reinforced layers, the hardening or softening characteristics become more prominent. We demonstrate that the stress–strain curves of geogrids and geotextile reinforced tailings under different reinforced layers can be fitted by the Duncan–Zhang model, which indicates that the pseudo-cohesion of shear strength index increases linearly whereas the friction angle remains primarily unchanged with the increase in reinforced layers. In addition, we observed that, although the strength of the reinforced tailings increases substantially, the reinforcement effect is more significant at a low confining pressure than at a high confining pressure. On the contrary, the triaxial specimen strength decreases with the increase in the number of reinforced layers. Our findings can provide valuable input toward the design and application of reinforced engineering.

Mechanical Properties of Bentonite-Sand Mixtures Under Triaxial Stress Condition

1994 ◽  
Vol 353 ◽  
Author(s):  
M. Umedera ◽  
A. Fujiwara ◽  
N. Yasufuku ◽  
M. Hyodo ◽  
H. Murata
Keyword(s):  
Mechanical Properties ◽  
Shear Strength ◽  
Water Content ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Strength Properties ◽  
Compression Tests ◽  
Optimum Water Content ◽  
Triaxial Compression Tests ◽  
Optimum Water

AbstractA series of triaxial compression tests is being conducted under the drained condition on bentonite and sand mixtures, known as buffer, in saturated and optimum water content states to clarify the mechanical properties of the buffer.It was found that the mechanical properties of bentonite and sand mixtures are strongly influenced by water and bentonite contents: shear strength in a saturated state is less than that in an optimum water content state; shear strength decreases rapidly with increasing bentonite content. Strength properties are much dependent on confining pressure.

Experimental Investigation on Mechanical Properties of Soft Rock under Instantaneous Triaxial Compression

2012 ◽  
Vol 594-597 ◽  
pp. 218-221
Author(s):  
Yu Wang ◽  
Feng Liu
Keyword(s):  
Mechanical Properties ◽  
Shear Failure ◽  
Triaxial Compression ◽  
Deformation Modulus ◽  
Soft Rock ◽  
Confining Pressure ◽  
Test System ◽  
Compression Tests ◽  
Confining Pressures ◽  
Failure Angle

Using the RMT-150C rock mechanics test system, the instantaneous triaxial compression tests for muddy siltstone were carried out under different confining pressures, and the instantaneous mechanical properties of soft rock were obtained. The results show that the strength parameters of sample have a positive linear relation with the confining pressure, and the sensitivity of peak strength on the confining pressure is higher than that of residual strength. The elastic and deformation modulus of sample linearly increase with the confining pressure going up, and the elastic modulus is more sensitive to the confining pressure. The soft rock sample shows typical ductility failure characteristic, while the damage characteristic is mainly shear failure and the shear failure angle linearly decreases with the confining pressure going up.

Experimental Study on Shear Strength Considering Initial Void Ratio and Plasticity Index

2013 ◽  
Vol 405-408 ◽  
pp. 63-67
Author(s):  
Xing Chen Wang ◽  
Ri Qing Xu ◽  
Jian Feng Zhu
Keyword(s):  
Shear Strength ◽  
Void Ratio ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Deviatoric Stress ◽  
Plasticity Index ◽  
Test Results ◽  
Compression Tests ◽  
Functional Relationships ◽  
Initial Void Ratio

A series of drained triaxial compression tests under different conditions were performed to quantitatively study the influence of the initial void ratio and plasticity index on the shear strength of remolded saturated clays. The test results show that both the peak stress friction angle and peak deviatoric stress decrease with increasing initial void ratio and plasticity index of the soil under the same confining pressure; whereas, they increase with increasing confining pressure of the soil under the same initial void ratio and plasticity index. A new synthesized physical parameter λ, which simultaneously represent both the type and the condition of remolded saturated clays, is defined based on the test results in this work. The functional relationships among the parameters φd and peak deviatoric stress in Mohr-Coulomb equation and the parameter λ are established to develop a modified Mohr-Coulomb equation by considering physical properties of soil. In this equation, only two input parameters, i.e., λ and the confine pressure, are needed to predict the shear strength of the soil. In order to check the accuracy of the proposed equation, laboratory tests were conducted to evaluate against the predicted results. The results show that the peak shear strength of remolded saturated clays can be well described by the proposed equation. Key words: shear strength; Mohr-Coulomb equation; remolded saturated clays; initial void ratio; plasticity index.

scholarly journals Disturbance Evolution Behavior of Loess Soil under Triaxial Compression

2020 ◽  
Vol 2020 ◽  
pp. 1-14
Author(s):  
Yali Xu ◽  
Panpan Guo
Keyword(s):  
Triaxial Compression ◽  
Deformation Modulus ◽  
Loess Soil ◽  
Confining Pressure ◽  
Compression Tests ◽  
Structural Effects ◽  
Moisture Contents ◽  
Confining Pressures ◽  
Evolution Behavior ◽  
Disturbance Function

This paper presents an investigation into the evolution law of the structural effects of Xi’an loess soil, based on the disturbed state concept. First, a series of consolidated and drained triaxial compression tests were performed on undisturbed and remoulded loess samples prepared at five different moisture contents and tested at four different confining pressures. Second, two disturbance functions with different parameters were proposed to quantify mathematically the structural effects of loess. Finally, the proposed disturbance functions were validated against documented test results by other researchers. The results indicated that the single-parameter disturbance function, with the deformation modulus as its parameter, provides convenience for application but takes no account of the respective contributions of deviatoric stress and mean stress to the disturbance evolution behavior of loess. The double-parameter disturbance function, with the shear and bulk moduli as its parameters, is capable of distinguishing these respective contributions and reflects well the disturbance evolution behavior of loess under various moisture contents and confining pressures. The effects of moisture content and confining pressure on the parameters of the disturbance functions were found to be unsteady. The proposed disturbance functions lay the foundation for establishing a constitutive model for loess accounting for the structural effect.

scholarly journals Experimental Investigation on Failure Modes and Mechanical Properties of Rock-Like Specimens with a Grout-Infilled Flaw under Triaxial Compression

2019 ◽  
Vol 2019 ◽  
pp. 1-14
Author(s):  
Huilin Le ◽  
Shaorui Sun ◽  
Feng Zhu ◽  
Haotian Fan
Keyword(s):  
Mechanical Properties ◽  
Rock Mass ◽  
Epoxy Resin ◽  
Failure Modes ◽  
Shear Failure ◽  
Fractured Rock ◽  
Triaxial Compression ◽  
Friction Angle ◽  
Confining Pressure ◽  
Compression Tests

Flaws existing in rock mass are one of the main factors resulting in the instability of rock mass. Epoxy resin is often used to reinforce fractured rock mass. However, few researches focused on mechanical properties of the specimens with a resin-infilled flaw under triaxial compression. Therefore, in this research, epoxy resin was selected as the grouting material, and triaxial compression tests were conducted on the rock-like specimens with a grout-infilled flaw having different geometries. This study draws some new conclusions. The high confining pressure suppresses the generation of tensile cracks, and the failure mode changes from tensile-shear failure to shear failure as the confining pressure increases. Grouting with epoxy resin leads to the improvement of peak strengths of the specimens under triaxial compression. The reinforcement effect of epoxy resin is better for the specimens having a large flaw length and those under a relatively low confining pressure. Grouting with epoxy resin reduces the internal friction angle of the samples but improves their cohesion. This research may provide some useful insights for understanding the mechanical behaviors of grouted rock masses.

scholarly journals Effect of Particle Sizes on the Physical and Mechanical Properties of Briquettes

Energies ◽  
2019 ◽  
Vol 12 (19) ◽  
pp. 3618 ◽  
Author(s):  
Longlong Pang ◽  
Yuzhong Yang ◽  
Liyun Wu ◽  
Fei Wang ◽  
Han Meng
Keyword(s):  
Mechanical Properties ◽  
Particle Size ◽  
Triaxial Compression ◽  
Deformation Modulus ◽  
Physical And Mechanical Properties ◽  
Compression Tests ◽  
Uniaxial Compression Strength ◽  
Coal Particles ◽  
Basic Reference ◽  
Tectonic Coal

The particle size of coal particles is an important factor affecting the physical and mechanical properties of coal. In this study, uniaxial and triaxial compression tests were conducted to investigate the effects of coal particle size on the physical and mechanical properties of briquettes and their impact mechanism using a rock mechanics test-150B servo system (RMT-150B). The results showed that the uniaxial compression strength, elastic modulus and deformation modulus of briquettes increase when particle size is decreased. The deformation characteristics of the briquettes directly prepared by raw tectonic coal were similar to those of coal specimens with a particle size of 0.18–0.25 mm. The cohesion and strength of coal specimens increased when particle size was decreased, and the plastic deformation capacity decreased when particle size was decreased, showing a strong correlation. The f briquette directly prepared by the raw tectonic coal had a strength between that of coal specimens with a particle size of 2–6 mm and those with a particle size of 0.18–0.25 mm. The mechanical properties of briquettes mainly depend on the meshing force between the coal particles. The smaller the particles, the greater the mechanical meshing force. The “floating particles”, generated in the voids between coal particles during the preparation process, are a significant factor affecting the plasticity characteristics. The research results may be used as a basic reference in the study of the mechanical properties of tectonic coal, gas migration and coal and gas outburst mechanisms.

Sign in / Sign up

Export Citation Format

Share Document