Experimental Investigation on Mechanical Properties of Soft Rock under Instantaneous Triaxial Compression

2012 ◽  
Vol 594-597 ◽  
pp. 218-221
Author(s):  
Yu Wang ◽  
Feng Liu
Keyword(s):  
Mechanical Properties ◽  
Shear Failure ◽  
Triaxial Compression ◽  
Deformation Modulus ◽  
Soft Rock ◽  
Confining Pressure ◽  
Test System ◽  
Compression Tests ◽  
Confining Pressures ◽  
Failure Angle

Using the RMT-150C rock mechanics test system, the instantaneous triaxial compression tests for muddy siltstone were carried out under different confining pressures, and the instantaneous mechanical properties of soft rock were obtained. The results show that the strength parameters of sample have a positive linear relation with the confining pressure, and the sensitivity of peak strength on the confining pressure is higher than that of residual strength. The elastic and deformation modulus of sample linearly increase with the confining pressure going up, and the elastic modulus is more sensitive to the confining pressure. The soft rock sample shows typical ductility failure characteristic, while the damage characteristic is mainly shear failure and the shear failure angle linearly decreases with the confining pressure going up.

scholarly journals Disturbance Evolution Behavior of Loess Soil under Triaxial Compression

2020 ◽  
Vol 2020 ◽  
pp. 1-14
Author(s):  
Yali Xu ◽  
Panpan Guo
Keyword(s):  
Triaxial Compression ◽  
Deformation Modulus ◽  
Loess Soil ◽  
Confining Pressure ◽  
Compression Tests ◽  
Structural Effects ◽  
Moisture Contents ◽  
Confining Pressures ◽  
Evolution Behavior ◽  
Disturbance Function

This paper presents an investigation into the evolution law of the structural effects of Xi’an loess soil, based on the disturbed state concept. First, a series of consolidated and drained triaxial compression tests were performed on undisturbed and remoulded loess samples prepared at five different moisture contents and tested at four different confining pressures. Second, two disturbance functions with different parameters were proposed to quantify mathematically the structural effects of loess. Finally, the proposed disturbance functions were validated against documented test results by other researchers. The results indicated that the single-parameter disturbance function, with the deformation modulus as its parameter, provides convenience for application but takes no account of the respective contributions of deviatoric stress and mean stress to the disturbance evolution behavior of loess. The double-parameter disturbance function, with the shear and bulk moduli as its parameters, is capable of distinguishing these respective contributions and reflects well the disturbance evolution behavior of loess under various moisture contents and confining pressures. The effects of moisture content and confining pressure on the parameters of the disturbance functions were found to be unsteady. The proposed disturbance functions lay the foundation for establishing a constitutive model for loess accounting for the structural effect.

scholarly journals Experimental Investigation on Failure Modes and Mechanical Properties of Rock-Like Specimens with a Grout-Infilled Flaw under Triaxial Compression

2019 ◽  
Vol 2019 ◽  
pp. 1-14
Author(s):  
Huilin Le ◽  
Shaorui Sun ◽  
Feng Zhu ◽  
Haotian Fan
Keyword(s):  
Mechanical Properties ◽  
Rock Mass ◽  
Epoxy Resin ◽  
Failure Modes ◽  
Shear Failure ◽  
Fractured Rock ◽  
Triaxial Compression ◽  
Friction Angle ◽  
Confining Pressure ◽  
Compression Tests

Flaws existing in rock mass are one of the main factors resulting in the instability of rock mass. Epoxy resin is often used to reinforce fractured rock mass. However, few researches focused on mechanical properties of the specimens with a resin-infilled flaw under triaxial compression. Therefore, in this research, epoxy resin was selected as the grouting material, and triaxial compression tests were conducted on the rock-like specimens with a grout-infilled flaw having different geometries. This study draws some new conclusions. The high confining pressure suppresses the generation of tensile cracks, and the failure mode changes from tensile-shear failure to shear failure as the confining pressure increases. Grouting with epoxy resin leads to the improvement of peak strengths of the specimens under triaxial compression. The reinforcement effect of epoxy resin is better for the specimens having a large flaw length and those under a relatively low confining pressure. Grouting with epoxy resin reduces the internal friction angle of the samples but improves their cohesion. This research may provide some useful insights for understanding the mechanical behaviors of grouted rock masses.

scholarly journals Experimental Study on Rock-Like Specimens with Single Flaw under Hydro-Mechanical Coupling

2019 ◽  
Vol 9 (16) ◽  
pp. 3234 ◽  
Author(s):  
Jinquan Xing ◽  
Cheng Zhao ◽  
Songbo Yu ◽  
Hiroshi Matsuda ◽  
Chuangchuang Ma
Keyword(s):  
Mechanical Properties ◽  
Shear Failure ◽  
Water Pressure ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Tensile Failure ◽  
Compression Tests ◽  
Cracking Behavior ◽  
Mechanical Coupling ◽  
High Confining Pressure

In order to study the mechanical characteristics and cracking behavior of jointed rock mass under hydro-mechanical coupling, a series of uniaxial compression tests and triaxial compression tests were carried out on cylinder gypsum specimens with a single pre-existing flaw. Under different confining pressures, water pressure was injected on the pre-existing flaw surface through a water injection channel. The geometrical morphology and tensile or shear properties of the cracks were determined by X-ray computed tomography (CT) and scanning electron microscope (SEM). Based on the macro and micro observation, nine types of cracks that caused the specimen failure are summarized. The results of mechanical properties and crack behavior showed that the confining pressure inhibited the tensile cracks, and shear failure occurred under high confining pressure. The water pressure facilitated the initiation and extension of tensile crack, which made the specimens prone to tensile failure. However, under the condition of high confining pressure and low water pressure, the lubrication effect had a significant effect on the failure pattern, under which the specimens were prone to shear failure. This experimental research on mechanical properties and cracking behavior under hydro-mechanical coupling is expected to increase its fundamental understanding.

Mechanical Properties of Sandstone under Loading and Unloading Conditions

2014 ◽  
Vol 852 ◽  
pp. 441-446 ◽  
Author(s):  
Xing Xia Wang ◽  
Wen Juan Ma ◽  
Jian Wen Huang ◽  
Zai Yi Liao
Keyword(s):  
Mechanical Properties ◽  
Triaxial Compression ◽  
Deformation Modulus ◽  
Confining Pressure ◽  
Rock Deformation ◽  
Test Results ◽  
Compression Tests ◽  
Triaxial Compressive Strength ◽  
Unloading Confining Pressure ◽  
Triaxial Compression Tests

The mechanical properties of rock mass under unloading conditions are essentially different from that under loading conditions. Triaxial compression tests and unloading confining pressure tests are conducted, and test results show that unloading failure is more brittle, and rock samples suffer more damage under unloading failure. The larger the initial confining pressure is, the easier of unloading failure is occurred. The increasing or decreasing values of rock deformation modulus under unloading conditions are within 10% of rock triaxial compressive strength. Unloading failure leads to deterioration of rock deformation modulus, which decreases gradually with confining pressure decreasing, and the decrease rates get bigger and bigger with unloading ratio of confining pressure increasing. Deformation modulus is only 24-34% of that under loading condition when rock strength goes down to residual strength.

Behaviors of Xiashu Loess in the Lower Reaches of China’s Yangtze River under Triaxial Compression and the Microscopic Explanations

2016 ◽  
Vol 858 ◽  
pp. 91-97
Author(s):  
Jun Hua Xiao ◽  
Wen Qi Zheng
Keyword(s):  
Mechanical Properties ◽  
Yangtze River ◽  
Shear Failure ◽  
Triaxial Compression ◽  
Processing Technique ◽  
Point Of View ◽  
Image Processing Technique ◽  
Test Results ◽  
Compression Tests ◽  
Triaxial Compression Tests

To investigate the macroscopic mechanical properties of undisturbed structural Xiashu loess in the lower reaches of China’s Yangtze River under triaxial compression, and obtain the intrinsic explanations for the macroscopic mechanical properties from the microscopic point of view, in laboratory, triaxial compression tests were carried out, microstructure images of sheared samples were collected by scanning electron microscope (SEM), and quantitative parameters of microstructure (mainly about particle or pore size, distribution, and alignment) were extracted by digital image processing technique. Based on the test results, the deviator stress-strain relationships of both undisturbed and remoulded Xiashu loess, the structural strength, and the microstructural evolution mechanism about the formation of shear failure zone of Xiashu loess under triaxial compression were analyzed.

scholarly journals Mechanical Properties and Numerical Analyses of Basalt Fiber Crumb Rubber Mortars in Soft Rock Roadways

2019 ◽  
Vol 2019 ◽  
pp. 1-13 ◽  
Author(s):  
Jun-Ling Qin ◽  
Wei-Guo Qiao ◽  
Deng-Ge Lin ◽  
Shuai Zhang ◽  
Ji-Yao Wang
Keyword(s):  
Constitutive Model ◽  
Triaxial Compression ◽  
Basalt Fiber ◽  
Soft Rock ◽  
Crumb Rubber ◽  
Compression Tests ◽  
Confining Pressures ◽  
Roadway Support ◽  
Uniaxial Compressive Stress ◽  
Triaxial Compression Tests

The strength of crumb rubber mortars can be improved by the addition of basalt fibers. However, limited studies have been conducted on basalt fiber crumb rubber mortars (BF-CRM), and the constitutive model is still very immature. In this paper, uniaxial compressive stress-strain curves are obtained for several groups of BF-CRM specimens with different contents. By comparison with the GZH model, modified GZH parameters that can be used in a BF-CRM constitutive model are obtained. Then, taking the support scheme of the main substation of a mine as the background, FLAC3D is used to simulate the roadway support, BF-CRM replaces the ordinary mortars in the original support, and triaxial compression tests are performed at different confining pressures. In this way, the application of BF-CRM in roadway support is studied and analyzed.

scholarly journals Cracking Behaviors and Mechanical Properties of Rock-Like Specimens with Two Unparallel Flaws under Conventional Triaxial Compression

2019 ◽  
Vol 2019 ◽  
pp. 1-15 ◽  
Author(s):  
Huilin Le ◽  
Shaorui Sun ◽  
Chenghua Xu ◽  
Liuyang Li ◽  
Yong Liu
Keyword(s):  
Mechanical Properties ◽  
Inclination Angle ◽  
Failure Modes ◽  
Shear Failure ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Critical Value ◽  
Tensile Failure ◽  
Rock Bridge ◽  
Bridge Length

Flaws existing in rock masses are generally unparallel and under three-dimensional stress; however, the mechanical and cracking behaviors of the specimens with two unparallel flaws under triaxial compression have been rarely studied. Therefore, this study conducted comprehensive research on the cracking and coalescence behavior and mechanical properties of specimens with two unparallel flaws under triaxial compression. Triaxial compressive tests were conducted under different confining pressures on rock-like specimens with two preexisting flaws but varying flaw geometries (with respect to the inclination angle of the two unparallel flaws, rock bridge length, and rock bridge inclination angle). Six crack types and eleven coalescence types in the bridge region were observed, and three types of failure modes (tensile failure, shear failure, and tensile-shear failure) were observed in experiments. Test results show that bridge length and bridge inclination angle have an effect on the coalescence pattern, but the influence of bridge inclination angle is larger than that of the bridge length. When the confining pressure is low, coalescence patterns and failure modes of the specimens are greatly affected by flaw geometry, but when confining pressure rose to a certain level, the influence of confining pressure is larger than the effect of flaw geometry. The peak strength of the specimens is affected by flaw geometry and confining pressure. There is a critical value for the bridge length. If the bridge length is larger than the critical value, peak strengths of the samples almost keep constant as the bridge length increases. In addition, as the bridge inclination angle increases, there is an increase in the probability of tensile cracks occurring, and with an increase in the confining pressure, the probability of the occurrence of shear cracks increases.

Mechanical Properties of Bentonite-Sand Mixtures Under Triaxial Stress Condition

1994 ◽  
Vol 353 ◽  
Author(s):  
M. Umedera ◽  
A. Fujiwara ◽  
N. Yasufuku ◽  
M. Hyodo ◽  
H. Murata
Keyword(s):  
Mechanical Properties ◽  
Shear Strength ◽  
Water Content ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Strength Properties ◽  
Compression Tests ◽  
Optimum Water Content ◽  
Triaxial Compression Tests ◽  
Optimum Water

AbstractA series of triaxial compression tests is being conducted under the drained condition on bentonite and sand mixtures, known as buffer, in saturated and optimum water content states to clarify the mechanical properties of the buffer.It was found that the mechanical properties of bentonite and sand mixtures are strongly influenced by water and bentonite contents: shear strength in a saturated state is less than that in an optimum water content state; shear strength decreases rapidly with increasing bentonite content. Strength properties are much dependent on confining pressure.

scholarly journals Investigation on the relationship between CT numbers and marble failure under different confining pressures

2021 ◽  
Vol 60 (1) ◽  
pp. 846-852
Author(s):  
Yang Yan-Shuang ◽  
Li Kai-Yue ◽  
Zhou Hui ◽  
Tian Hao-Yuan ◽  
Cheng Wei ◽  
...  
Keyword(s):  
Damage Mechanics ◽  
Triaxial Compression ◽  
Ct Scanning ◽  
Confining Pressure ◽  
Triaxial Tests ◽  
Compression Tests ◽  
Ct Number ◽  
Confining Pressures ◽  
Loading Tests ◽  
Rock Specimens

Abstract Computed tomography (CT) scanning technology is helpful in investigating rock materials as it can demonstrate the micro structure of rock clearly. Conventional triaxial compression tests and the corresponding graded triaxial loading tests were carried out to investigate the complex failure mechanism of the marble at the Jinping Hydropower Station. After that CT-scanning tests were done on the loaded marble specimens. The test results show that (1) the CT numbers of the specimens have a certain statistical regularity, that is, the CT numbers of the specimens under different confining pressures satisfy the Weibull distribution, as the confining pressure increases, the mean values rise while variances decrease; (2) in the two groups of tests, the average CT numbers corresponding to the conventional triaxial tests are higher than those corresponding to the graded loading tests, but the CT number variances are lower than those of the graded loading tests; and (3) according to meso-damage mechanics, the damage variables of the rock specimens were established based on the definition of CT numbers. The calculation results show that the damage variables decrease with the increase in confining pressure, the damage variables of the rock specimens in the graded loading tests are higher than those in the conventional triaxial test, and the differences between the two loading tests have grown with the increase in confining pressure.

scholarly journals Mechanical Properties of Sandstones under Initial Unloading Damage

2021 ◽  
Vol 2021 ◽  
pp. 1-12
Author(s):  
Hengbin Zhang ◽  
Lehua Wang ◽  
Jianlin Li ◽  
Huafeng Deng ◽  
Xiaoliang Xu
Keyword(s):  
Mechanical Properties ◽  
Rock Mass ◽  
Shear Failure ◽  
Rock Sample ◽  
Triaxial Compression ◽  
Deformation Modulus ◽  
Peak Strength ◽  
Repeated Loading ◽  
Adjustment Process ◽  
Loading Test

To study the influence of initial unloading damage on the mechanical properties of sandstone, the repeated loading test of unloading damaged sandstone was carried out considering 8 initial unloading quantities of 100%, 93.33%, 86.67%, 80%, 73.33%, 66.67%, 40%, and 0%. The results were compared with those of the triaxial compression test of intact samples. The results show that the peak strength of intact samples is higher than that of unloading damaged samples, and the difference is more obvious when the unloading quantity is more than 80%. During the unloading process, the strain increasing rate of rock samples is obvious, and the lateral dilatation is significant, and the deformation modulus and compressive strength of the rock sample deteriorate obviously. From the energy point of view, the greater the unloading damage, the smaller the stored elastic strain energy, which leads to the decrease of peak strength. At present, the unloading fracture inside the rock sample has developed, and the failure mode of the sample gradually changes from compression shear failure to tensile shear failure. In the process of engineering rock mass excavation, the unloading area and unloading damage amount of the rock mass is a dynamic adjustment process. To ensure the safety of the engineering rock mass, it is suggested to determine reasonable reinforcement time, reinforcement area, and reinforcement measures.

Sign in / Sign up

Export Citation Format

Share Document