scholarly journals Effect of Particle Sizes on the Physical and Mechanical Properties of Briquettes

Energies ◽  
2019 ◽  
Vol 12 (19) ◽  
pp. 3618 ◽  
Author(s):  
Longlong Pang ◽  
Yuzhong Yang ◽  
Liyun Wu ◽  
Fei Wang ◽  
Han Meng
Keyword(s):  
Mechanical Properties ◽  
Particle Size ◽  
Triaxial Compression ◽  
Deformation Modulus ◽  
Physical And Mechanical Properties ◽  
Compression Tests ◽  
Uniaxial Compression Strength ◽  
Coal Particles ◽  
Basic Reference ◽  
Tectonic Coal

The particle size of coal particles is an important factor affecting the physical and mechanical properties of coal. In this study, uniaxial and triaxial compression tests were conducted to investigate the effects of coal particle size on the physical and mechanical properties of briquettes and their impact mechanism using a rock mechanics test-150B servo system (RMT-150B). The results showed that the uniaxial compression strength, elastic modulus and deformation modulus of briquettes increase when particle size is decreased. The deformation characteristics of the briquettes directly prepared by raw tectonic coal were similar to those of coal specimens with a particle size of 0.18–0.25 mm. The cohesion and strength of coal specimens increased when particle size was decreased, and the plastic deformation capacity decreased when particle size was decreased, showing a strong correlation. The f briquette directly prepared by the raw tectonic coal had a strength between that of coal specimens with a particle size of 2–6 mm and those with a particle size of 0.18–0.25 mm. The mechanical properties of briquettes mainly depend on the meshing force between the coal particles. The smaller the particles, the greater the mechanical meshing force. The “floating particles”, generated in the voids between coal particles during the preparation process, are a significant factor affecting the plasticity characteristics. The research results may be used as a basic reference in the study of the mechanical properties of tectonic coal, gas migration and coal and gas outburst mechanisms.

scholarly journals An Experimental Study on Preparation of Reconstituted Tectonic Coal Samples: Optimization of Preparation Conditions

Energies ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2846
Author(s):  
Jishi Geng ◽  
Liwen Cao ◽  
Congyu Zhong ◽  
Shuai Zhang
Keyword(s):  
Mechanical Properties ◽  
Particle Size ◽  
Moisture Content ◽  
Coalbed Methane ◽  
P Wave ◽  
Preparation Conditions ◽  
P Wave Velocity ◽  
Coal Particles ◽  
Mining Safety ◽  
Tectonic Coal

The uniquely soft and fragile nature of tectonic coal makes it difficult to obtain core samples suitable for laboratory experimentation. Preparation of reconstituted tectonic coal (RTC) samples generally adopts the secondary forming method. Reliable coal samples are needed to obtain credible permeability and mechanical parameters that can guide Coalbed Methane (CBM) extraction and improve mining safety. In this study, the compaction mechanism of coal particles is analyzed based on the Kawakita model, and optimal sample preparation conditions are systemically investigated, particularly particle size and particle size distribution, forming pressure, and moisture content. The density and P-wave velocity of coal samples were used to test whether the RTC samples were realistic. Finally, the mechanical properties and deformation characteristics of the RTC samples were determined. The results indicate that RTC samples prepared for laboratory testing of mechanical properties require (1) the original particle size of the tectonic coal to be retained as much as possible; (2) a forming pressure that compacts the sample similar to the original tectonic coal; and (3) an optimum moisture content.

Mechanical Properties of Sandstone under Loading and Unloading Conditions

2014 ◽  
Vol 852 ◽  
pp. 441-446 ◽  
Author(s):  
Xing Xia Wang ◽  
Wen Juan Ma ◽  
Jian Wen Huang ◽  
Zai Yi Liao
Keyword(s):  
Mechanical Properties ◽  
Triaxial Compression ◽  
Deformation Modulus ◽  
Confining Pressure ◽  
Rock Deformation ◽  
Test Results ◽  
Compression Tests ◽  
Triaxial Compressive Strength ◽  
Unloading Confining Pressure ◽  
Triaxial Compression Tests

The mechanical properties of rock mass under unloading conditions are essentially different from that under loading conditions. Triaxial compression tests and unloading confining pressure tests are conducted, and test results show that unloading failure is more brittle, and rock samples suffer more damage under unloading failure. The larger the initial confining pressure is, the easier of unloading failure is occurred. The increasing or decreasing values of rock deformation modulus under unloading conditions are within 10% of rock triaxial compressive strength. Unloading failure leads to deterioration of rock deformation modulus, which decreases gradually with confining pressure decreasing, and the decrease rates get bigger and bigger with unloading ratio of confining pressure increasing. Deformation modulus is only 24-34% of that under loading condition when rock strength goes down to residual strength.

Experimental Investigation on Mechanical Properties of Soft Rock under Instantaneous Triaxial Compression

2012 ◽  
Vol 594-597 ◽  
pp. 218-221
Author(s):  
Yu Wang ◽  
Feng Liu
Keyword(s):  
Mechanical Properties ◽  
Shear Failure ◽  
Triaxial Compression ◽  
Deformation Modulus ◽  
Soft Rock ◽  
Confining Pressure ◽  
Test System ◽  
Compression Tests ◽  
Confining Pressures ◽  
Failure Angle

Using the RMT-150C rock mechanics test system, the instantaneous triaxial compression tests for muddy siltstone were carried out under different confining pressures, and the instantaneous mechanical properties of soft rock were obtained. The results show that the strength parameters of sample have a positive linear relation with the confining pressure, and the sensitivity of peak strength on the confining pressure is higher than that of residual strength. The elastic and deformation modulus of sample linearly increase with the confining pressure going up, and the elastic modulus is more sensitive to the confining pressure. The soft rock sample shows typical ductility failure characteristic, while the damage characteristic is mainly shear failure and the shear failure angle linearly decreases with the confining pressure going up.

scholarly journals Experimental Analysis of the Mechanical Properties and Resistivity of Tectonic Coal Samples with Different Particle Sizes

Energies ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2303
Author(s):  
Congyu Zhong ◽  
Liwen Cao ◽  
Jishi Geng ◽  
Zhihao Jiang ◽  
Shuai Zhang
Keyword(s):  
Mechanical Properties ◽  
Particle Size ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Uniaxial Compressive Strength ◽  
Coalbed Methane ◽  
Coal Sample ◽  
Fine Particles ◽  
Particle Sizes ◽  
Tectonic Coal

Because of its weak cementation and abundant pores and cracks, it is difficult to obtain suitable samples of tectonic coal to test its mechanical properties. Therefore, the research and development of coalbed methane drilling and mining technology are restricted. In this study, tectonic coal samples are remodeled with different particle sizes to test the mechanical parameters and loading resistivity. The research results show that the particle size and gradation of tectonic coal significantly impact its uniaxial compressive strength and elastic modulus and affect changes in resistivity. As the converted particle size increases, the uniaxial compressive strength and elastic modulus decrease first and then tend to remain unchanged. The strength of the single-particle gradation coal sample decreases from 0.867 to 0.433 MPa and the elastic modulus decreases from 59.28 to 41.63 MPa with increasing particle size. The change in resistivity of the coal sample increases with increasing particle size, and the degree of resistivity variation decreases during the coal sample failure stage. In composite-particle gradation, the proportion of fine particles in the tectonic coal sample increases from 33% to 80%. Its strength and elastic modulus increase from 0.996 to 1.31 MPa and 83.96 to 125.4 MPa, respectively, and the resistivity change degree decreases. The proportion of medium particles or coarse particles increases, and the sample strength, elastic modulus, and resistivity changes all decrease.

Experimental investigation of the mechanical behavior of glass fiber/high fluidity polyamide-based composites for automotive market

2021 ◽  
pp. 073168442110140
Author(s):  
Hossein Ramezani-Dana ◽  
Moussa Gomina ◽  
Joël Bréard ◽  
Gilles Orange
Keyword(s):  
Mechanical Properties ◽  
Glass Fiber ◽  
Mechanical Performance ◽  
Physical And Mechanical Properties ◽  
Ultimate Strain ◽  
Uniaxial Tensile ◽  
Compression Tests ◽  
Automotive Market ◽  
Glass Fiber Reinforced ◽  
Glass Fiber Reinforcement

In this work, we examine the relationships between the microstructure and the mechanical properties of glass fiber–reinforced polyamide 6,6 composite materials ( V f = 54%). These materials made by thermocompression incorporate different grades of high fluidity polyamide-based polymers and two types of quasi-UD glass fiber reinforcement. One is a classic commercial fabric, while the other specially designed and manufactured incorporates weaker tex glass yarns (the spacer) to increase the planar permeability of the preform. The effects of the viscosity of the polymers and their composition on the wettability of the reinforcements were analyzed by scanning electron microscopy observations of the microstructure. The respective influences of the polymers and the spacer on the mechanical performance were determined by uniaxial tensile and compression tests in the directions parallel and transverse to the warp yarns. Not only does the spacer enhance permeability but it also improves physical and mechanical properties: tensile longitudinal Young’s modulus increased from 38.2 GPa to 42.9 GPa (13% growth), tensile strength increased from 618.9 MPa to 697 MPa (3% growth), and decrease in ultimate strain from 1.8% to 1.7% (5% reduction). The correlation of these results with the damage observed post mortem confirms those acquired from analyses of the microstructure of composites and the rheological behaviors of polymers.

scholarly journals Effect of freeze–thaw cycle on physical and mechanical properties and damage characteristics of sandstone

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Longxiao Chen ◽  
Kesheng Li ◽  
Guilei Song ◽  
Deng Zhang ◽  
Chuanxiao Liu
Keyword(s):  
Mechanical Properties ◽  
Shear Failure ◽  
Triaxial Compression ◽  
Physical And Mechanical Properties ◽  
Freeze Thaw ◽  
Damage Characteristics ◽  
Large Pore ◽  
Natural Rock ◽  
Thaw Cycle ◽  
Freeze Thaw Cycle

AbstractRock deterioration under freeze–thaw cycles is a concern for in-service tunnel in cold regions. Previous studies focused on the change of rock mechanical properties under unidirectional stress, but the natural rock mass is under three dimensional stresses. This paper investigates influences of the number of freeze–thaw cycle on sandstone under low confining pressure. Twelve sandstone samples were tested subjected to triaxial compression. Additionally, the damage characteristics of sandstone internal microstructure were obtained by using acoustic emission (AE) and mercury intrusion porosimetry. Results indicated that the mechanical properties of sandstone were significantly reduced by freeze–thaw effect. Sandstone’ peak strength and elastic modulus were 7.28–37.96% and 6.38–40.87% less than for the control, respectively. The proportion of super-large pore and large pore in sandstone increased by 19.53–81.19%. We attributed the reduced sandstone’ mechanical properties to the degenerated sandstone microstructure, which, in turn, was associated with increased sandstone macropores. The macroscopic failure pattern of sandstone changed from splitting failure to shear failure with an increasing of freeze–thaw cycles. Moreover, the activity of AE signal increased at each stage, and the cumulative ringing count also showed upward trend with the increase of freeze–thaw number.

scholarly journals Effect of Particle Size Distribution on Laser Powder Bed Fusion Manufacturability of Copper

2021 ◽  
Author(s):  
Massimiliano Bonesso ◽  
Pietro Rebesan ◽  
Claudio Gennari ◽  
Simone Mancin ◽  
Razvan Dima ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Particle Size ◽  
Particle Size Distribution ◽  
Size Distribution ◽  
Physical And Mechanical Properties ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Powder Bed ◽  
Cooling Channels ◽  
Scan Speed

AbstractOne of the major benefits of the Laser Powder Bed Fusion (LPBF) technology is the possibility of fabrication of complex geometries and features in only one-step of production. In the case of heat exchangers in particular, this is very convenient for the fabrication of conformal cooling channels which can improve the performance of the heat transfer capability. Yet, obtaining dense copper parts printed via LPBF presents two major problems: the high reflectivity of 1 μm (the wavelength of commonly used laser sources) and the high thermal conductivity of copper that limits the maximum local temperature that can be attained. This leads to the formation of porous parts.In this contribution, the influence of the particle size distribution of the powder on the physical and mechanical properties of parts produced via LPBF is studied. Three copper powders lots with different particle size distributions are used in this study. The effect on densification from two laser scan parameters (scan speed and hatching distance) and the influence of contours scans on the lateral surface roughness is reported. Subsequently, samples manufactured with the optimal process parameters are tested for thermal and mechanical properties evaluation.

Behaviors of Xiashu Loess in the Lower Reaches of China’s Yangtze River under Triaxial Compression and the Microscopic Explanations

2016 ◽  
Vol 858 ◽  
pp. 91-97
Author(s):  
Jun Hua Xiao ◽  
Wen Qi Zheng
Keyword(s):  
Mechanical Properties ◽  
Yangtze River ◽  
Shear Failure ◽  
Triaxial Compression ◽  
Processing Technique ◽  
Point Of View ◽  
Image Processing Technique ◽  
Test Results ◽  
Compression Tests ◽  
Triaxial Compression Tests

To investigate the macroscopic mechanical properties of undisturbed structural Xiashu loess in the lower reaches of China’s Yangtze River under triaxial compression, and obtain the intrinsic explanations for the macroscopic mechanical properties from the microscopic point of view, in laboratory, triaxial compression tests were carried out, microstructure images of sheared samples were collected by scanning electron microscope (SEM), and quantitative parameters of microstructure (mainly about particle or pore size, distribution, and alignment) were extracted by digital image processing technique. Based on the test results, the deviator stress-strain relationships of both undisturbed and remoulded Xiashu loess, the structural strength, and the microstructural evolution mechanism about the formation of shear failure zone of Xiashu loess under triaxial compression were analyzed.

Sign in / Sign up

Export Citation Format

Share Document