Modeling and Optimized Design of a New Multi-DOF Deflection Type PM Motor

2014 ◽  
Vol 951 ◽  
pp. 67-70
Author(s):  
Zheng Li ◽  
Lu Zhang ◽  
Qing Qing Lun
Keyword(s):  
Finite Element ◽  
Element Model ◽  
Optimized Design ◽  
Initial Model ◽  
Analysis Software ◽  
Technology Study ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Structure Configuration ◽  
The Magnetic Field

Based on the finite element analysis software, this paper innovatively proposes a multi-DOF deflection type PM motor with "6-8" rotor-stator structure and builds its finite element model. Furthermore, the distribution of the magnetic field of this motor are analyzed and calculated. To obtain better performance, the motor’s structure is optimized and designed with response surface methodology (RSM). Results of the proposed structure configuration are analyzed and compared with the initial model. It is expected that this research can be helpful to the multi-DOF motor or actuator technology study and improvements.

The Finite-Element Analysis of Cylindrical Helical Tooth Milling Cutter Based on Marc

2011 ◽  
Vol 52-54 ◽  
pp. 1147-1152
Author(s):  
Guang Guo Zhang ◽  
Wei Jiang ◽  
Hong Hua Zhang ◽  
Huan Wang
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Cutting Forces ◽  
Element Model ◽  
Local Deformation ◽  
Analysis Software ◽  
Element Analysis ◽  
Milling Cutter ◽  
Cutter Life ◽  
The Finite Element Analysis

In the traditional designs of milling cutter, we cannot get the required accuracy of machining as there may be local deformation on the edges, even more the cutter can break down. Aiming at this situation, a finite-element model of straight pin milling cutter with helical tooth are built using Marc, a nonlinear finite-element analysis software, the different cutting forces of the milling cutter during the cutting process are analyzed and the cutting forces of the milling cutter at different parameters are studied. We get the stress, the strain and the temperature distribution of the milling cutter in different situation. Our work offer a theoretical basis of improving stress of the cutter, designing the structure of cutters reasonably and analyzing the cutter failure as well as a new method of analysis and calculation of the cutter life and strength.

Finite Element Analysis of the Greenhouse Canopy Effect with Seismic Load

2011 ◽  
Vol 368-373 ◽  
pp. 1125-1129
Author(s):  
Chang Jiang Liu ◽  
Jin Long Wang
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Seismic Analysis ◽  
Element Model ◽  
Seismic Load ◽  
Analysis Software ◽  
Element Analysis ◽  
Canopy Effect ◽  
The Finite Element Analysis ◽  
The Finite Element Model

The finite element model about greenhouse canopy of seismic analysis was setted up, The finite element analysis software ANSYS was used to study structure displacement, stress analysis on greenhouse shed. The results showed that the dangerous part of the canopy were located on upper chord members,lower chord members, web members of the framework and the lower and upper, the inside of both sides of the wall with seismic load.Corresponding to this results ,the main destroied form were the framework damage caused by the bending deformation of upper chord members, lower chord members and the upper web members and the unstability caused by the distortion of both sides of the wall.

Finite Element Modal Analysis of Whole Structure of Spherical Grinder

2013 ◽  
Vol 677 ◽  
pp. 273-277
Author(s):  
Xiao Xin Gong ◽  
Qiang Lu
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Modal Analysis ◽  
Element Model ◽  
Analysis Software ◽  
Element Analysis ◽  
Improvement Measure ◽  
The Finite Element Analysis ◽  
Improved Design ◽  
Ansys Workbench

In order to analyze vibration characteristics of whole structure of the spherical grinder, the finite element analysis software is applied to finite element modal analysis of the structure. 3D model of spherical grinder is established by Pro/ENGINEER software. Finite element model of spherical grinder is established in the finite element analysis software ANSYS Workbench. The previous 6-order inherent frequencies and the corresponding vibration modes are obtained through the finite element calculation. According to the vibration intensity distribution, the corresponding improvement measure is put forward. It provides theoretical basis for dynamic analysis and improved design of spherical grinder.

The Static and Dynamic Characteristics Study of Aluminum Tank Semitrailer

2011 ◽  
Vol 189-193 ◽  
pp. 2233-2237 ◽  
Author(s):  
Ya Qiong Deng ◽  
Jin Gang Wang ◽  
Yi Wen ◽  
Shuang Zhao ◽  
Li Li Dai
Keyword(s):  
Finite Element ◽  
Dynamic Performance ◽  
Element Model ◽  
Work Conditions ◽  
Stress And Strain ◽  
Performance Parameters ◽  
Analysis Software ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Strength And Stiffness

Taking an aluminum tank semitrailer as an example, this essay aim to analyze the strength and stiffness of the tank semitrailer and obtain stress and strain characteristics under different conditions on the basis of a finite element model, by using the finite element analysis software. By carrying on modal analysis in different work conditions, the essay gets the dynamic performance parameters of the tank. The results show that the tank fully meets the requirements of using, and the performance parameters of the tank will be foundation for the optimization.

IMPACTS OF PRE-STRESS LOSS ON THE LONG-TERM DEFLECTION FOR LONG-SPAN PC CONTINUOUS GIRDER BRIDGE

2014 ◽  
Vol 1 (1) ◽  
Author(s):  
Jianqing Bu ◽  
Jincan Cui
Keyword(s):  
Finite Element ◽  
Element Model ◽  
Analysis Software ◽  
Element Analysis ◽  
Girder Bridges ◽  
Long Span ◽  
The Finite Element Analysis ◽  
Continuous Girder Bridge ◽  
Girder Bridge

In order to analyze the impacts of pre-stress loss on the long-term deflection for long-span PC continuous girder bridges, this paper presents a numerical analysis using the finite element analysis software MIDAS/Civil based on a long-span PC continuous box-section girder bridge in Shijiazhuang. Once the 3-D finite element model was established, the influences of different pre-stress loss levels and locations were analyzed in a numerical simulation. Pre-stress loss is often the key reason for long-term deflection in long-span PC continuous girder bridges, so we can estimate the development of deflection by considering these factors during the operation.

Finite Element Analysis of Nonuniformity of Tires with Imperfections5

2007 ◽  
Vol 35 (3) ◽  
pp. 226-238 ◽  
Author(s):  
K. M. Jeong ◽  
K. W. Kim ◽  
H. G. Beom ◽  
J. U. Park
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Radial Force ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Dimensional Finite Element ◽  
Force Variation ◽  
Three Dimensional Finite Element

Abstract The effects of variations in stiffness and geometry on the nonuniformity of tires are investigated by using the finite element analysis. In order to evaluate tire uniformity, a three-dimensional finite element model of the tire with imperfections is developed. This paper considers how imperfections, such as variations in stiffness or geometry and run-out, contribute to detrimental effects on tire nonuniformity. It is found that the radial force variation of a tire with imperfections depends strongly on the geometrical variations of the tire.

Analysis of Hydroelectric Unit’s Upper Bracket Based on Test and FEM

2014 ◽  
Vol 721 ◽  
pp. 131-134
Author(s):  
Mi Mi Xia ◽  
Yong Gang Li
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Element Model ◽  
The Finite Element Method ◽  
Ansys Software ◽  
Element Analysis ◽  
Hydroelectric Unit ◽  
The Finite Element Analysis ◽  
Strain Rosette ◽  
The Finite Element Model

To research the load upper bracket of Francis hydroelectric unit, then established the finite-element model, and analyzed the structure stress of 7 operating condition points with the ANSYS software. By the strain rosette test, acquired the data of stress-strain in the area of stress concentration of the upper bracket. The inaccuracy was considered below 5% by analyzing the contradistinction between the finite-element analysis and the test, and match the engineering precision and the test was reliable. The finite-element method could be used to judge the stress of the upper bracket, and it could provide reference for the Structural optimization and improvement too.

Finite Element Analysis and Optimization of the Truss of Installing Wave-Maker Based on ANSYS

2013 ◽  
Vol 313-314 ◽  
pp. 1038-1041
Author(s):  
Shou Jun Wang ◽  
Xing Xiong ◽  
Chao Li
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Design Parameters ◽  
Analysis Software ◽  
Element Analysis ◽  
Large Span ◽  
The Finite Element Analysis ◽  
Wave Maker

According to uncertainty of the design parameters for large span truss of installing wave-maker, in order to avoid the waste of materials,the truss is analyzed based on the finite element analysis software ANSYS to find out its weaknesses and various parts of the deformation. On the premise of ensuring the intensity and stiffness, the weight of the truss is reduced by adjusting its sizes and selecting different profiles, so as to achieve the optimization of the truss of installing wave-maker.

Experimental Research on the Magnetic Field Sensitive Polymeric Actuator

2011 ◽  
Vol 287-290 ◽  
pp. 603-607
Author(s):  
Chun Lin Xia ◽  
Yang Fang Wu ◽  
Qian Qian Lu
Keyword(s):  
Magnetic Field ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Energy Conversion ◽  
Experimental Research ◽  
Experimental Results ◽  
Deformation Characteristics ◽  
Analysis Software ◽  
Element Analysis ◽  
The Magnetic Field

Using domestic MFSP membrane as a medium of energy conversion, a kind of MFSP actuator was designed. The dedicated test equipment was constructed for experimental research, and the experimental results were given. The strip and circular MSFP membrane were analyzed qualitatively to obtain the deformation characteristics of membrane by finite element analysis software.

Sign in / Sign up

Export Citation Format

Share Document