Application of Pressure Test System in Dispenser for Gasoline

2010 ◽  
Vol 97-101 ◽  
pp. 4243-4246
Author(s):  
Zhan Shu He ◽  
Ya Jun Liu ◽  
Jun Liu ◽  
Jia Bao Wang
Keyword(s):  
Gas Separation ◽  
Performance Optimization ◽  
Digital Signal ◽  
Test System ◽  
Signal Acquisition ◽  
Excessive Pressure ◽  
Pressure Transducers ◽  
Reliable Diagnosis ◽  
Pressure Test ◽  
Oil Gas

In the dispenser for gasoline there exist three problems: excessive pressure caused by water hammer, inadequacy of oil-gas separation and cavitation. A pressure test system of the dispenser for gasoline is established by using pressure transducers and a digital signal acquisition system. Results show that the pressure test system can not only conduct real-time and reliable diagnosis of the dispenser pressure, but also provide guideline on its performance optimization.

Portable Pressure Test System for Brake of Rail Transit

2014 ◽  
Vol 530-531 ◽  
pp. 245-248
Author(s):  
Sen Jie Cui ◽  
Chang Qi Yang
Keyword(s):  
Pressure Sensors ◽  
Power Source ◽  
Test System ◽  
Rail Transit ◽  
Signal Acquisition ◽  
Single Chip ◽  
Pressure Signal ◽  
Whole Process ◽  
Pressure Test ◽  
Acquisition Device

This paper designs a pressure signal acquisition device for brake of rail transit, and establish a framework for the pressure signal test system based on the Single Chip Micyoco (SCM for short) C8051F350. It gives a brief introduction of the whole process for the test system, and emphatically analysis the part of the pressure sensors, the power source, the display and the communication. Lastly, we adjust the factor of the whole test system and assemble the system to test the pressure portably.

Signal Acquisition and Processing in Hydraulic Components Test System

2013 ◽  
Vol 846-847 ◽  
pp. 972-976
Author(s):  
Xiao Teng Zeng
Keyword(s):  
Signal Processing ◽  
Digital Signal Processing ◽  
Performance Test ◽  
Performance Testing ◽  
Digital Signal ◽  
Test System ◽  
Processing Method ◽  
Signal Acquisition ◽  
Performance Parameters ◽  
Signal Acquisition And Processing

The key to the performance test system for hydraulic components is to realize real, fast and accurate signal acquisition and processing. By analysis the analog and digital signal processing during hydraulic components Performance testing, a new signal flow scheme is proposed. It described in detail the acquisition and processing method of serial signals and PLC signals, thus solving the lag and distortion during signal processing and realizing the real-time display of data and the automatic report of performance parameters during hydraulic components testing process.

The Design and Realization of Airborne Electrical Equipments’ Online Test System in the Environments of Mechanics

2014 ◽  
Vol 687-691 ◽  
pp. 1038-1043
Author(s):  
Yong Tao Yu ◽  
Ming Chen ◽  
Feng Tian ◽  
Ying Ji Shan
Keyword(s):  
High Efficiency ◽  
Dynamic Test ◽  
Digital Signal ◽  
Test System ◽  
Experimental Result ◽  
Signal Acquisition ◽  
Online Test ◽  
Development Tool ◽  
The Stability ◽  
Software Development Tool

Current OTS (Online Test System, OTS) of airborne electrical equipments in the environments of mechanics is only able to test statically but dynamically. To solve the problem, a new kind of dynamic test system based on PXI bus is designed. In the design, modular instrument resources that used in the third generation of ATE (Auto Test System, ATE) commonly is adopted to prove the system’s reusability, extensibility and standard ability, digital signal acquisition is replaced with analog signal acquisition to realize dynamic test, support from the method of process monitoring is drew to get the capability to detect the reversible failure in UUT (Unit Under Test, UTT), VC++ language is used as the software development tool to control the system and record test data. In the special mechanics environment such as centrifuge, drawing lessons from the experience of the new concept dynamic test, the system architecture of remote control acquisition is used to prove the stability and efficiency of the test system greatly. The experimental result shows that the system runs well and has more advantages such as high efficiency of auto-test and reliability of failure diagnosis results, meeting new demand of the airborne electrical equipments’ online test in the environments of mechanics.

An Engine Dynamic Signal Testing System Based on Virtual Instrument Technology

2009 ◽  
Vol 16-19 ◽  
pp. 193-198 ◽  
Author(s):  
Ying Ji Liu ◽  
Feng Tian Cai ◽  
Wei Zhou ◽  
Xue Li Zhang ◽  
Tian Xia Zhang
Keyword(s):  
Virtual Instrument ◽  
High Speed ◽  
Computer Software ◽  
Digital Signal ◽  
Test System ◽  
Structure Design ◽  
Signal Acquisition ◽  
Instrument Technology ◽  
Dynamic Signal ◽  
Engine Dynamic

Aimed at the requirements of engine experimental research，a test system of engine dynamic signal was developed based on virtual instrument technology. The integral structure design of the system was given, the hardware is composed of sensors, signal conditioning module, high-speed data acquisition card and portable computer; the host computer software was developed with DASYLab, a virtual instrumentation tool. Its essential is to make good use of computer to achieve and extend functions of traditional instruments, by comprehensively using technologies of computer, digital signal processing, standard bus and software engineering method, functions of continuous multi channel sampling and multi type signal acquisition, and processing analysis were realized. The field test shows the system works reliably, development and application of this system can provide detailed experiment data and a new way in the field of engine power detection.

Study on Common Ground Testing Platform Technology for Telemetry Core Equipment

2012 ◽  
Vol 220-223 ◽  
pp. 1472-1475
Author(s):  
Qiu Lin Tan ◽  
Xiang Dong Pei ◽  
Si Min Zhu ◽  
Ji Jun Xiong
Keyword(s):  
Data Exchange ◽  
Common Ground ◽  
Digital Signal ◽  
Test System ◽  
Automatic Test System ◽  
Module Design ◽  
The Status ◽  
Output Module ◽  
And Performance ◽  
Hardware Circuit

On the basis of automatic test system of the status in domestic and foreign, by analysis of the various functions and performance of the integrated test system, a design of the integrated test system is proposed, FPGA as the core logic controller of the hardware circuit. The system of the hardware design include: digital signal source output modules, analog output module and PCM codec module. Design of hardware circuit are mainly described. In addition, a detailed analysis of some key technologies in the design process was given. Overall, its data exchange with host computer is through the PCI card, data link and bandwidth can be expanded in accordance with the actual needs. The entire system designed in the modular principle, which has a strong scalability.

The Integrated Mechanical Function Test System of Material and Structural Fatigue Damage

2012 ◽  
Vol 532-533 ◽  
pp. 398-402
Author(s):  
Yu Lan Wei ◽  
Bing Li ◽  
Sui Ying Jin ◽  
Kai Kai Chen
Keyword(s):  
Optimal Design ◽  
Test System ◽  
Integrated System ◽  
Detection Methods ◽  
Signal Acquisition ◽  
Mechanical Function ◽  
Structural Fatigue ◽  
Material Functions ◽  
Function Test ◽  
And Function

An integrated system to measure mechanical functions of material or structure is introduced. This system is able to provide more detection methods and experiment environments. And it can discover the characteristics and mechanisms of damnification and breakage in materials, considering the effects of loading and environments. Material functions were analyzed in many aspects, including loading, strain, light, sound, temperature and infrared to ensure the safety of materials and configuration of unmanned plane. Current study has laid a foundation for realizing optimal design of unmanned plane. In this paper, theory, components, and function of the system were discussed, as well as signal acquisition and analysis.

Evaluation of Foam Inhibitors at the Jusepin Oil/Gas Separation Plant, El Furrial Field, Eastern Venezuela

1992 ◽  
Author(s):  
F. Cassani ◽  
P. Ortega ◽  
A. Davila ◽  
W. Rodriguez ◽  
J. Seranno
Keyword(s):  
Gas Separation ◽  
Separation Plant ◽  
Oil Gas

scholarly journals Optimum Design of Structural Parameters for Thin-walled Metal Container

2019 ◽  
Vol 288 ◽  
pp. 01007
Author(s):  
Liao Hongbo ◽  
Yang Dan ◽  
Yin Fenglong ◽  
Liang Xiaodong ◽  
Li Erkang ◽  
...  
Keyword(s):  
Structural Parameters ◽  
Optimization Method ◽  
External Pressure ◽  
Test System ◽  
Manufacturing Cost ◽  
Thin Wall ◽  
Pressure Test ◽  
Critical Instability ◽  
Thin Walled ◽  
Better Than

In order to further increase the volume, reduce the weight and manufacturing cost, the key structural parameters of thin-walled metal packing container are optimized. The instability conditions under circumferential external pressure and axial load are analyzed, a mathematical model with the constraint of critical instability strength, the maximum volume and minimum mass as the objective is constructed. Multi-objective optimization method with nonlinear constraints is used to solve the key structural parameters, such as wall thickness, diameter and height, and the optimization result is calculated by fgoalattain() function in the Matlab optimization toolbox. The instability pressure test system is constructed, the instability pressure of the optimized thin-wall metal packing container is tested. The results show that the unstable pressure is higher than 120kPa, which are better than the design index.

Study on Combustor Outlet Temperature Field of Gas Turbine

2011 ◽  
Vol 138-139 ◽  
pp. 962-966 ◽  
Author(s):  
Kai Liu ◽  
Li Xu
Keyword(s):  
Experimental Study ◽  
Temperature Field ◽  
Gas Turbine ◽  
Reference Value ◽  
Test System ◽  
Outlet Temperature ◽  
Test Results ◽  
Heavy Duty ◽  
Pressure Test ◽  
Heavy Duty Gas Turbine

Experimental study on combustor outlet temperature field of heavy-duty gas turbine had been finished on high-pressure test system. Experimental results indicate: The OTDF is sensitive to diameter of dilution holes, and the RTDF is sensitive to location of dilution holes. The test results have important guiding significance and reference value to design, commission and working about the similar combustor.

Sign in / Sign up

Export Citation Format

Share Document