Investigation of the Effect of Abutment Angle Tolerance on the Stress Created in the Fixture and Screw in Dental Implants Using Finite Element Analysis

2021 ◽  
Vol 51 ◽  
pp. 63-76
Author(s):  
Bijan Mohammadi ◽  
Zahra Abdoli ◽  
Ehsan Anbarzadeh
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Distribution ◽  
Dental Implants ◽  
Maximum Stress ◽  
Element Analysis ◽  
Bone Implant ◽  
Implant Placement ◽  
And Control ◽  
Biomechanical Factors

Today, an artificial tooth root called a dental implant is used to replace lost tooth function. Treatment with dental implants is considered an effective and safe method. However, in some cases, the use of dental implants had some failures. The success of dental implants is influenced by several biomechanical factors such as loading type, used material properties, shape and geometry of implants, quality and quantity of bone around implants, surgical method, lack of rapid and proper implant surface's integration with the jaw bone, etc. The main purpose of functional design is to investigate and control the stress distribution on dental implants to optimize their performance. Finite element analysis allows researchers to predict the stress distribution in the bone implant without the risk and cost of implant placement. In this study, the stresses created in the 3A.P.H.5 dental implant's titanium fixture and screw due to the change in abutment angles tolerance have been investigated. The results show that although the fixture and the screw's load and conditions are the same in different cases, the change of the abutment angle and the change in the stress amount also made a difference in the location of maximum stress. The 21-degree abutment puts the fixture in a more critical condition and increases the chance of early plasticization compared to other states. The results also showed that increasing the abutment angle to 24 degrees reduces the stress in the screw, but decreasing the angle to 21 degrees leads to increased screw stress and brings it closer to the fracture.

scholarly journals Finite Element Analysis of Stress in Bone and Abutment-Implant Interface under Static and Cyclic Loadings

2020 ◽  
Author(s):  
Saeed Nokar ◽  
Hamid Jalali ◽  
Farideh Nozari ◽  
Mahnaz Arshad
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Concentration ◽  
Stress Distribution ◽  
Maximum Stress ◽  
Von Mises Stress ◽  
Element Analysis ◽  
Bone Implant ◽  
Factors Affecting ◽  
Von Mises

Objectives: The success of implant treatment depends on many factors affecting the bone-implant, implant-abutment, and abutment-prosthesis interfaces. Stress distribution in bone plays a major role in success/failure of dental implants. This study aimed to assess the pattern of stress distribution in bone and abutment-implant interface under static and cyclic loadings using finite element analysis (FEA). Materials and Methods: In this study, ITI implants (4.1×12 mm) placed at the second premolar site with Synocta abutments and metal-ceramic crowns were simulated using SolidWorks 2007 and ABAQUS software. The bone-implant contact was assumed to be 100%. The abutments were tightened with 35 Ncm preload torque according to the manufacturer’s instructions. Static and cyclic loads were applied in axial (116 Ncm), lingual (18 Ncm), and mesiodistal (24 Ncm) directions. The maximum von Mises stress and strain values ​​were recorded. Results: The maximum stress concentration was at the abutment neck during both static and cyclic loadings. Also, maximum stress concentration was observed in the cortical bone. The loading stress was higher in cyclic than static loading. Conclusion: Within the limitations of this study, it can be concluded that the level of stress in single-unit implant restorations is within the tolerable range by bone.

Effect of length and diameter on stress distribution pattern of INDIDENT dental implants by finite element analysis

2012 ◽  
Vol 2 (1) ◽  
pp. 19 ◽  
Author(s):  
Bobin Saluja ◽  
Masood Alam ◽  
T Ravindranath ◽  
A Mubeen ◽  
Nidhi Adya ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Distribution ◽  
Distribution Pattern ◽  
Dental Implants ◽  
Element Analysis

scholarly journals Stress Distribution in Implant-Supported Overdenture and Peri-Implant Bone Using Three Attachment Systems: A Finite Element Analysis

2021 ◽  
Vol 13 (2) ◽  
pp. 57-61
Author(s):  
Alireza Izadi ◽  
Fariboorz Vafaie ◽  
Armaghan Shahbazi ◽  
Mohamad Taghi Mokri vala
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Distribution ◽  
Maximum Stress ◽  
Titanium Implants ◽  
Load Application ◽  
Von Mises Stress ◽  
Bone Block ◽  
Element Analysis ◽  
Minimum Stress

Background: This finite element analysis (FEA) evaluated stress distribution in implant-supported overdenture (ISO) and peri-implant bone using one extracoronal (ball) and two intracoronal (locator and Zest Anchor Advanced Generation (ZAAG)) attachment systems. Methods: In this in vitro study, the mandible was modelled in the form of an arc-shaped bone block with 33 mm height and 8 mm width. Two titanium implants were modelled at the site of canine teeth, and three attachments (ZAGG, locator, and ball) were placed over them. Next, 100 N load was applied at 90° and 30° angles from the molar site of each quadrant to the implants. The stress distribution pattern in the implants and the surrounding bone was analyzed, and the von Mises stress around the implants and in the crestal bone was calculated. Results: While minimum stress in peri-implant bone following load application at 30° angle was noted in the mesial point of the locator attachment, maximum stress was recorded at the distal point of the ball attachment following load application at 90° angle. Maximum stress around the implant following load application at 90° angle was noted in the lingual point of the ball attachment while minimum stress was recorded in the lingual point of the locator attachment following load application at 90° angle. Conclusions: According to the results, the locator attachment is preferred to the ZAAG attachment, and the ball attachment should be avoided if possible.

scholarly journals Evaluation of Stress Distribution and Force in External Hexagonal Implant: A 3-D Finite Element Analysis

2021 ◽  
Vol 18 (19) ◽  
pp. 10266
Author(s):  
Vinod Bandela ◽  
Ram Basany ◽  
Anil Kumar Nagarajappa ◽  
Sakeenabi Basha ◽  
Saraswathi Kanaparthi ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Distribution ◽  
Maximum Stress ◽  
Axial Direction ◽  
Von Mises Stress ◽  
P Value ◽  
Implant Surface ◽  
Element Analysis ◽  
Von Mises

Purpose: To analyze the stress distribution and the direction of force in external hexagonal implant with crown in three different angulations. Materials and Methods: A total of 60 samples of geometric models were used to analyze von Mises stress and direction of force with 0-, 5-, and 10-degree lingual tilt. Von Mises stress and force distribution were evaluated at nodes of hard bone, and finite element analysis was performed using ANSYS 12.1 software. For calculating stress distribution and force, we categorized and labeled the groups as Implant A1, Implant A2, and Implant A3, and Implant B1, Implant B2, and Implant B3 with 0-, 5-, and 10-degree lingual inclinations, respectively. Inter- and intra-group comparisons were performed using ANOVA test. A p-value of ≤0.05 was considered statistically significant. Results: In all the three models, overall maximum stress was found in implant model A3 on the implant surface (86.61), and minimum was found on model A1 in hard bone (26.21). In all the three models, the direction of force along three planes was maximum in DX (0.01025) and minimum along DZ (0.002) direction with model B1. Conclusion: Maximum von Mises stress and the direction of force in axial direction was found at the maximum with the implant of 10 degrees angulation. Thus, it was evident that tilting of an implant influences the stress concentration and force in external hex implants.

scholarly journals Effect of Offset Implant Placement on the Stress Distribution Around a Dental Implant: A Three-Dimensional Finite Element Analysis

2015 ◽  
Vol 41 (6) ◽  
pp. 646-651 ◽  
Author(s):  
Hakimeh Siadat ◽  
Shervin Hashemzadeh ◽  
Allahyar Geramy ◽  
Seyed Hossein Bassir ◽  
Marzieh Alikhasi
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Concentration ◽  
Stress Distribution ◽  
Dental Implant ◽  
Three Dimensional ◽  
Element Analysis ◽  
3D Finite Element ◽  
Implant Placement ◽  
Mandibular Molar

There are some anatomical restrictions in which implants are not possible to be inserted in their conventional configuration. Offset placement of implants in relation to the prosthetic unit could be a treatment solution. The aim of this study was to evaluate the effect of the offset placement of implant-supported prosthesis on the stress distribution around a dental implant using 3D finite element analysis. 3D finite element models of implant placement in the position of a mandibular molar with 4 configurations (0, 0.5, 1, 1.5 mm offset) were created in order to investigate resultant stress/strain distribution. A vertical load of 100 N was applied on the center of the crown of the models. The least stress in peri-implant tissue was found in in-line configuration (0 mm offset). Stress concentration in the peri-implant tissue increased by increasing the amount of offset placement. Maximum stress concentration in all models was detected at the neck of the implant. It can be concluded that the offset placement of a single dental implant does not offer biomechanical advantages regarding reducing stress concentration over the in-line implant configuration. It is suggested that the amount of offset should be as minimum as possible.

Effect of Design Parameters on Thermomechanical Stress in Silicon of Through-Silicon Via

2016 ◽  
Vol 138 (3) ◽  
Author(s):  
Joo-Sun Hwang ◽  
Seung-Ho Seo ◽  
Won-Jun Lee
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Distribution ◽  
Maximum Stress ◽  
Design Parameters ◽  
Element Analysis ◽  
Through Silicon Via ◽  
Dielectric Thickness ◽  
Thermomechanical Stress ◽  
Lower Region

We examined the effect of the design parameters of a through-silicon via (TSV) on the thermomechanical stress distribution at the bottom of the TSV using finite element analysis. Static analyses were carried out at 350 °C to simulate the maximum thermomechanical stress during postplating annealing. The thermomechanical stress is concentrated in the lower region of a TSV, and the maximum stress in silicon occurs at the bottom of the TSV. The TSV diameter and dielectric liner thickness were two important determinants of the maximum stress in the silicon. The maximum stress decreased with decreasing TSV diameter, whereas the effect of aspect ratio was negligible. A thick dielectric liner is advantageous for lowering the maximum stress in silicon. The minimum dielectric thickness resulting in a maximum stress less than the yield stress of silicon was 520, 230, and 110 nm for via diameters of 20, 10, and 5 μm, respectively. The maximum stress also decreased with the thickness of the copper overburden.

scholarly journals Comparative Analysis of Stress and Deformation between One-Fenced and Three-Fenced Dental Implants Using Finite Element Analysis

2021 ◽  
Vol 10 (17) ◽  
pp. 3986
Author(s):  
Chia-Hsuan Lee ◽  
Arvind Mukundan ◽  
Szu-Chien Chang ◽  
Yin-Lai Wang ◽  
Shu-Hao Lu ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Comparative Analysis ◽  
Stress Distribution ◽  
Dental Implant ◽  
Maximum Stress ◽  
Vertical Force ◽  
Element Analysis ◽  
Different Types ◽  
Stress And Deformation

Finite element analysis (FEA) has always been an important tool in studying the influences of stress and deformation due to various loads on implants to the surrounding jaws. This study assessed the influence of two different types of dental implant model on stress dissipation in adjoining jaws and on the implant itself by utilizing FEA. This analysis aimed to examine the effects of increasing the number of fences along the implant and to compare the resulting stress distribution and deformation with surrounding bones. When a vertical force of 100 N was applied, the largest displacements found in the three-fenced and single-fenced models were 1.7469 and 2.5267, respectively, showing a drop of 30.8623%. The maximum stress found in the three-fenced and one-fenced models was 13.518 and 22.365 MPa, respectively, showing a drop of 39.557%. Moreover, when an oblique force at 35° was applied, a significant increase in deformation and stress was observed. However, the three-fenced model still had less stress and deformation compared with the single-fenced model. The FEA results suggested that as the number of fences increases, the stress dissipation increases, whereas deformation decreases considerably.

Sign in / Sign up

Export Citation Format

Share Document