Dynamic Response and Fracture of High Strength Boride/Alumina Ceramic Composite

2006 ◽  
Vol 326-328 ◽  
pp. 1573-1576
Author(s):  
Dong Feng Cao ◽  
Li Sheng Liu ◽  
Jiang Tao Zhang
Keyword(s):  
Dynamic Response ◽  
Ceramic Composite ◽  
Split Hopkinson Pressure Bar ◽  
Dynamic Compression ◽  
High Strength ◽  
Alumina Ceramic ◽  
Hopkinson Pressure Bar ◽  
Dynamic Loadings ◽  
Split Hopkinson ◽  
Pressure Bar

Dynamic response and fracture of high strength boride/alumina ceramic composite were investigated by split Hopkinson pressure bar (SHPB) experiment in this paper. The compressive stress–strain curves and dynamic compression strength of the composites were tested. The surface’s microstructure of fractured composites were examined by using scanning electron microscope (SEM) to investigate the fracture mechanism. The results show that boride/alumina has high dynamic compressive strength and high Young’s modulus. The main fracture mode of the material is the fracture of the ceramic grains. The micro-voids and flaws, generated during the sintering and manufacturing of material and mechanical process of specimen, decrease the strength of the material because they provide the source of crack expansion when the material undergoes the dynamic loadings.

Experimental and Numerical Researches of Dynamic Failure of a High Strength Alumina/Boride Ceramic Composite

2008 ◽  
Vol 368-372 ◽  
pp. 713-716 ◽  
Author(s):  
Jiang Tao Zhang ◽  
Li Sheng Liu ◽  
Peng Cheng Zhai ◽  
Qing Jie Zhang
Keyword(s):  
Ceramic Composite ◽  
Failure Modes ◽  
Split Hopkinson Pressure Bar ◽  
Numerical Models ◽  
High Strength ◽  
Tensile Failure ◽  
Hopkinson Pressure Bar ◽  
Loading Direction ◽  
Split Hopkinson ◽  
Pressure Bar

The dynamic compressive behavior of Al2O3 (10% vol.) / TiB2 ceramic composite had been tested by using a split Hopkinson pressure bar in this paper. The results show that the main failure modes of the ceramic composite include crushed failure and split fracture along the loading direction. The former is the typical compressive failure of brittle materials. The later is tensile failure along the flaws produced during the composite manufacturing. The numerical simulation was also used to study the effect of the diameter/length ratio of the samples on the experimental results. The effect of the deformation in the bars’ ends, which contacted with the samples, was also studied in the numerical models.

scholarly journals Properties and Structure of X30MnAlSi26-4-3 High Strength Steel Subjected to Dynamic Compression Processes

2017 ◽  
Vol 62 (4) ◽  
pp. 2255-2260 ◽  
Author(s):  
A. Śmiglewicz ◽  
M. Jabłońska ◽  
W. Moćko ◽  
K. Kowalczyk ◽  
E. Hadasik
Keyword(s):  
Plastic Deformation ◽  
Split Hopkinson Pressure Bar ◽  
Dynamic Compression ◽  
True Strain ◽  
High Strength ◽  
Hopkinson Pressure Bar ◽  
Structure Changes ◽  
Split Hopkinson ◽  
Bar Test ◽  
Pressure Bar

Abstract The paper presents the results of investigation on X30MnAlSi26-4-3 austenitic steel subjected to dynamic compression using the split Hopkinson pressure bar. The strain rate was 3700 s−1. The compression test was also carried out without the use of breaking rings and then true strain was about 0.3. The split Hopkinson pressure bar test take only few milliseconds to complete during which time it is impossible to transfer the excess heat out of the specimen, therefore the test must be carried out in adiabatic conditions and so the increase of the temperature caused by the work of plastic deformation had to be calculated. The stepping load method was used in order to evaluate the effect of adiabatic heating on the properties of steel which allowed to maintain the isothermal deformation conditions. The paper presents the comparison of results obtained during deformation under adiabatic and isothermal conditions in correlation to structure changes occurring in course of dynamic compression.

Experimental Research of Foamed Ceramic Composite under Dynamic Loading Using SHPB

2013 ◽  
Vol 718-720 ◽  
pp. 112-116
Author(s):  
Xu Yang Li ◽  
Rui Yuan Huang ◽  
Yong Chi Li ◽  
Guang Fa Gao
Keyword(s):  
Ceramic Composite ◽  
Split Hopkinson Pressure Bar ◽  
Strain Rates ◽  
Test Results ◽  
Hopkinson Pressure Bar ◽  
Softening Effect ◽  
Stress Equilibrium ◽  
Split Hopkinson ◽  
Pressure Bar ◽  
Versus Strain

The Split Hopkinson Pressure Bar (SHPB) is used to investigate the dynamic compressive mechanical behavior of a new foamed ceramic composite under impact loading. The stress versus strain curves are obtained under high strain rates. The test results are considered to be able to assure conformability of the tests, validate the stress equilibrium assumption, and show that the stress versus strain curves of foamed ceramic composite display strain hardening effect and damage softening effect as brittle materials. Meanwhile the curve includes short plateau region while no densification region.

Construction of Johnson-Cook Model for Gr2 Titanium through Adiabatic Heating Calculation

2014 ◽  
Vol 487 ◽  
pp. 7-14 ◽  
Author(s):  
Xi Guang Deng ◽  
Song Xiao Hui ◽  
Wen Jun Ye ◽  
Xiao Yun Song
Keyword(s):  
Split Hopkinson Pressure Bar ◽  
Heating Temperature ◽  
Dynamic Compression ◽  
Adiabatic Heating ◽  
Model Fit ◽  
Testing System ◽  
Compression Tests ◽  
Hopkinson Pressure Bar ◽  
Split Hopkinson ◽  
Pressure Bar

This study derived the five parameters in Johnson-Cook equation of CP titanium Gr2. Quasi-static and dynamic compression tests were designed to measure mechanical properties at strain rates of 10-3s-1 and 6000s-1. In order to secure the validity of tested data, a novel fixture was proposed to reduce the displacement measurement error in MTS testing system and the signal processing procedure of compressive split Hopkinson pressure bar for the present study was demonstrated. With the tested data and calculated adiabatic heating temperature rise, parameters A, B, n, m, C have been derived based on mathematical deduction and solve. It was found that the constructed constitutive model fit the tested data well and was able to restore the yield strength value at high strain rate.

A comparative study on dynamic mechanical performance of concrete and rock

2015 ◽  
Author(s):  
Xia Zhengbing ◽  
Zhang Kefeng ◽  
Deng Yanfeng ◽  
Ge Fuwen
Keyword(s):  
Mechanical Performance ◽  
Split Hopkinson Pressure Bar ◽  
Dynamic Compression ◽  
Peak Strain ◽  
Hopkinson Pressure Bar ◽  
Dynamic Mechanical ◽  
Strain And Strain Rate ◽  
Split Hopkinson ◽  
Pressure Bar ◽  
Relationship Of

Recently, engineering blasting is widely applied in projects such as rock mineral mining, construction of underground cavities and field-leveling excavation. Dynamic mechanical performance of rocks has been gradually attached importance both in China and abroad. Concrete and rock are two kinds of the most frequently used engineering materials and also frequently used as experimental objects currently. To compare dynamic mechanical performance of these two materials, this study performed dynamic compression test with five different strain rates on concrete and rock using Split Hopkinson Pressure Bar (SHPB) to obtain basic dynamic mechanical parameters of them and then summarized the relationship of dynamic compressive strength, peak strain and strain rate of two materials. Moreover, specific energy absorption is introduced to confirm dynamic damage mechanisms of concrete and rock materials. This work can not only help to improve working efficiency to the largest extent but also ensure the smooth development of engineering, providing rich theoretical guidance for development of related engineering in the future.

Dynamic Response of Two Extrusive Igneous Rocks Using Split Hopkinson Pressure Bar Test

2021 ◽  
Vol 33 (6) ◽  
pp. 04021133
Author(s):  
Sunita Mishra ◽  
Tanusree Chakraborty ◽  
K. Seshagiri Rao
Keyword(s):  
Dynamic Response ◽  
Split Hopkinson Pressure Bar ◽  
Igneous Rocks ◽  
Hopkinson Pressure Bar ◽  
Split Hopkinson ◽  
Bar Test ◽  
Pressure Bar

An improved method for compressive stress-strain measurements at very high strain rates

1992 ◽  
Vol 438 (1902) ◽  
pp. 153-170 ◽  
Keyword(s):  
High Speed ◽  
Split Hopkinson Pressure Bar ◽  
Pure Copper ◽  
High Strength ◽  
Tungsten Alloy ◽  
High Speed Photography ◽  
Hopkinson Pressure Bar ◽  
Stress Strain ◽  
Split Hopkinson ◽  
Pressure Bar

This paper describes a modification of the split Hopkinson pressure bar, to allow compression testing of high strength metals at a strain rate of up to about 10 5 s –1 . All dimensions are minimized to reduce effects of dispersion and inertia, with specimens of the order of 1 mm diameter. Strain is calculated from the stress record and calibrated with high-speed photography. Particular attention has been paid to the accuracy of the technique, and errors arising from nonlinearity in the instrumentation, dispersion, frictional restraint and inertia have all been quantitatively assessed. Stress–strain results are presented of Ti 6A14V alloy, a high strength tungsten alloy, and pure copper.

Dynamic Compression Test of CFRP Laminates Using SHPB Technique

2014 ◽  
Vol 566 ◽  
pp. 122-127
Author(s):  
Takayuki Kusaka ◽  
Takanori Kono ◽  
Yasutoshi Nomura ◽  
Hiroki Wakabayashi
Keyword(s):  
Compressive Strength ◽  
Split Hopkinson Pressure Bar ◽  
Dynamic Compression ◽  
Failure Process ◽  
Compression Tests ◽  
Hopkinson Pressure Bar ◽  
Stress Strain ◽  
Cfrp Laminates ◽  
Split Hopkinson ◽  
Pressure Bar

A novel experimental method was proposed for characterizing the compressive properties of composite materials under impact loading. Split Hopkinson pressure bar system was employed to carry out the dynamic compression tests. The dynamic stress-strain relations could be precisely estimated by the proposed method, where the ramped input, generated by the plastic deformation of a zinc buffer, was effective to reduce the oscillation of the stress field in the specimen. The longitudinal strain of gage area could be estimated from the nominal deformation of gage area, and consequently the failure process could be grasped in detail from the stress-strain relation. The dynamic compressive strength of the material was slightly higher than the static compressive strength. In addition, the validity of the proposed method was confirmed by the computational and experimental results.

scholarly journals Dynamic deformations tests of Ni3Al based intermetallic alloy by using the split Hopkinson pressure bar technique

2019 ◽  
Vol 55 (1) ◽  
pp. 129-134
Author(s):  
P. Jozwik ◽  
M. Kopec ◽  
W. Polkowski ◽  
Z. Bojar
Keyword(s):  
Split Hopkinson Pressure Bar ◽  
Dynamic Compression ◽  
Intermetallic Alloy ◽  
Strong Impact ◽  
Strain Rates ◽  
Hopkinson Pressure Bar ◽  
Evaluation Point ◽  
Split Hopkinson ◽  
Pressure Bar ◽  
Deformation Tests

In this work, the Ni3Al-based intermetallic alloy was subjected to room temperature dynamic plastic deformation tests by using a split Hopkinson pressure bar technique. The dynamic compression processes were carried out at strain rates in the range of =(1.9x102 / 1x104 s-1). A strong impact of applied deformation conditions on microstructure and mechanical properties evolution in the examined Ni3Al intermetallic, was documented. Generally, very high maximum compressive stress values were obtained, reaching 5500 MPa for the sample deformed at the highest strain rate (i.e. ??=1x104 s-1). The results of performed SEM/EBSD evaluation point towards an occurrence of dynamic recovery and recrystallization phenomena in Ni3Al samples deformed at high strain rates.

Sign in / Sign up

Export Citation Format

Share Document