Size Effect in the Split Hopkinson Pressure Bar Experiment

For many structures, their service environment is very strict, and the requirements for the impact resistance of materials are very high. Therefore, the dynamic testing method has important scientific significance and application value for practical engineering. Split Hopkinson pressure bar (SHPB) is one of the most common experimental methods for obtaining dynamic mechanical properties of materials. However, there is no uniform standard for the size of the bars and specimens used in the test. Theoretically, the size has little influence on the experimental results, but it has not been proved by experiments. This paper mainly studies the influence of device/specimen sizes of split Hopkinson pressure bar through experiments, it is demonstrated that the sizes of bars and specimen have little effect on experimental results.

Experimental Work for Bar Straightness Effect Evaluation of Split Hopkinson Pressure Bar

Bar straightness is one of several factors that can affect the quality of the strain wave signal in a Split Hopkinson Pressure Bar (SHPB). Recently, it was found that the bar components of the SHPB at the Lightweight Structures Laboratory displayed a deviation in straightness because of manufacturing limitations. An evaluation was needed to determine whether the strain wave signals produced from this SHPB are acceptable or not. A numerical model was developed to investigate this effect. In this paper, experimental work was performed to evaluate the quality of the signal in the SHPB and to validate the numerical model. Good agreement between the experimental results and the numerical results was obtained for the strain rates and stress-strain relationship for mild steel ST37 and aluminum 6061 specimen materials. The recommended bar straightness tolerance is proposed as 0.36 mm per 100 mm.

Quasi-Static and Dynamic Mechanical Properties of a Ti-6Al-4V Titanium Alloy Produced Using Unconventional Manufacturing Methods

The purpose of this paper was to determine the mechanical properties of a Ti-6Al-4V titanium alloy produced by traditional CIP (Cold Isostatic Pressing) and by LENS (Laser Engineered Net Shaping), an additive manufacturing process. A reference material, being a commercial Ti-6Al-4V alloy, was also tested. The strength test specimens were produced from a high-quality, Grade 5 titanium powder. Each specimen had its density, porosity, and hardness determined. Compression curves were plotted for the tested materials from the strength test results with static and dynamic loads. These tests were performed on an UTS (Universal Testing Machine) and an SHPB (Split Hopkinson Pressure Bar) stand. The test results obtained led to the conclusion that the titanium alloy produced by CIP had lower strength performance parameters than its commercially-sourced counterpart. The LENS-produced specimens outperformed the commercially-sourced alloy both in static and dynamic load conditions.

Experimental Investigation on the Energy Properties and Failure Process of Thermal Shock Treated Sandstone Subjected to Coupled Dynamic and Static Loads

Thermal shock (TS) is known as the process where fractures are generated when rocks go through sudden temperature changes. In the field of deep rock engineering, the rock mass can be subjected to the TS process in various circumstances. To study the influence of TS on the mechanical behaviors of rock, sandstone specimens are heated at different high temperatures and three cooling methods (stove cooling, air cooling, and freezer cooling) are adopted to provide different cooling rates. The coupled dynamic and static loading tests are performed on the heated sandstone through a modified split Hopkinson pressure bar (SHPB) system. The influence of heating level and cooling rate on the dynamic compressive strength, energy dissipations, and fracturing characteristics is investigated based on the experimental data. The development of the microcracks of the sandstone specimens after the experiment is analyzed utilizing a scanning electron microscope (SEM). The extent of the development of the microcracks serves to explain the variation pattern of the mechanical responses and energy dissipations of the specimens obtained from the loading test. The findings of this study are valuable for practices in rock engineering involving high temperature and fast cooling.

Study on dynamic mechanical properties and constitutive model description of Inconel718

In this study, the effects of strain rate and temperature on the flow stress of Inconel718 were analyzed by Split Hopkinson Pressure Bar (SHPB) experiment and quasi-static compression experiment. The classical JC constitutive model was established by combining the quasi-static compression experiment with the SHPB experiment. According to the effects of different grain sizes and [Formula: see text] phase on dislocation pile-up, the dislocation pile-up theory was introduced to modify the JC constitutive model. The modified constitutive model was compiled in FORTRAN language, and VUMAT user material subroutine was called and secondary development was carried out to establish the polycrystalline simulation model with different grain sizes. The uniaxial tensile and compression simulation process of polycrystal with different grain sizes was performed. Through comparing the simulation results with the experimental data. The correlation coefficient R, between the simulation and experimental values, is 0.97,981, and the average relative error is only 3.72%. The accuracy of the modified constitutive model was verified.