Effect of Local Wall Thinning on Maximum Load Carrying Capacities of Elbows under Bending

2007 ◽  
Vol 345-346 ◽  
pp. 517-520
Author(s):  
Jong Hyun Kim ◽  
Joong Hyuk Ahn ◽  
Seok Pyo Hong ◽  
Yun Jae Kim ◽  
Chi Yong Park
Keyword(s):  
Three Dimensional ◽  
Limit Load ◽  
Maximum Load ◽  
Small Strain ◽  
Perfectly Plastic ◽  
Wall Thinning ◽  
Plastic Materials ◽  
Load Carrying ◽  
Elastic Perfectly Plastic ◽  
Local Wall Thinning

This paper provides closed-form plastic limit load solutions for elbows with local wall thinning under in-plane bending, via three-dimensional (3-D), small strain FE limit analyses using elastic-perfectly plastic materials. Wide ranges of elbow and thinning geometries are considered.

Finite Element Based Plastic Loads for Elbows With Local Wall Thinning

2007 ◽  
Author(s):  
Jong-Hyun Kim ◽  
Chang-Sik Oh ◽  
Joon-Hyuk Ahn ◽  
Yun-Jae Kim ◽  
Chi-Yong Park ◽  
...  
Keyword(s):  
Finite Element ◽  
Large Strain ◽  
Three Dimensional ◽  
Geometry Effect ◽  
Perfectly Plastic ◽  
Wall Thinning ◽  
Plastic Materials ◽  
Wide Range ◽  
Elastic Perfectly Plastic ◽  
Local Wall Thinning

Based on systematic three-dimensional (3-D), large strain FE limit analyses using elastic-perfectly plastic materials, this paper quantifies the effect of local wall thinning on plastic behaviors and TES (twice-elastic-slope) plastic loads for 90° elbows under in-plane bending. The thinning geometry is assumed to be rectangular rather than circular, but the nonlinear geometry effect is fully considered. Results from systematic analyses lead to simple approximations for TES plastic loads, covering a wide range of elbow and thinning geometries.

Plastic Limit Loads for Piping Branch Junctions

2007 ◽  
Vol 345-346 ◽  
pp. 1377-1380 ◽  
Author(s):  
Yun Jae Kim ◽  
Kuk Hee Lee ◽  
Chi Yong Park
Keyword(s):  
Three Dimensional ◽  
Limit Load ◽  
Plastic Limit ◽  
Perfectly Plastic ◽  
Plastic Materials ◽  
Wide Range ◽  
Pipe Radius ◽  
Plastic Limit Load ◽  
The Mean ◽  
Elastic Perfectly Plastic

The present work presents plastic limit load solutions for branch junctions under internal pressure and in-plane bending, based on detailed three-dimensional (3-D) FE limit analyses using elastic-perfectly plastic materials. The proposed solutions are valid for a wide range of branch junction geometries; ratios of the branch-to-run pipe radius and thickness from 0.0 to 1.0, and the mean radius-to-thickness ratio of the run pipe from 5.0 to 20.0.

Reference Stress Solutions for Idealized Branch Junctions

2007 ◽  
Author(s):  
Yun-Jae Kim ◽  
Kuk-Hee Lee
Keyword(s):  
Three Dimensional ◽  
Limit Load ◽  
Perfectly Plastic ◽  
Reference Stress ◽  
Plastic Materials ◽  
Pipe Radius ◽  
Plastic Limit Load ◽  
The Mean ◽  
Elastic Perfectly Plastic ◽  
Good Agreement

The present work presents plastic limit load solutions for thin-walled branch junctions under internal pressure and in-plane bending, based on detailed three-dimensional (3-D) FE limit analyses using elastic-perfectly plastic materials. The proposed solutions are valid to ratios of the branch-to-run pipe radius and thickness from 0.0 to 1.0, and the mean radius-to-thickness ratio of the run pipe from 5.0 to 20.0. Comparison with FE results shows good agreement.

Limit loads for thin‐walled piping branch junctions under combined pressure and in‐plane bending

2008 ◽  
Vol 43 (2) ◽  
pp. 87-108 ◽  
Author(s):  
Y‐J Kim ◽  
K‐H Lee ◽  
C‐Y Park
Keyword(s):  
Branch Pipe ◽  
Three Dimensional ◽  
Limit Load ◽  
Small Strain ◽  
Limit Loads ◽  
Perfectly Plastic ◽  
Dimensional Finite Element ◽  
Plane Bending ◽  
Elastic Perfectly Plastic ◽  
Three Dimensional Finite Element

Closed‐form yield loci are proposed for branch junctions under combined pressure and in‐plane bending, via small‐strain three‐dimensional finite element (FE) limit load analyses using elastic—perfectly plastic materials. Two types of bending loading are considered: bending on the branch pipe and that on the run pipe. For bending on the run pipe, the effect of the bending direction is further considered. Comparison with extensive FE results shows that predicted limit loads using the proposed solutions are overall conservative and close to FE results. The proposed solutions are believed to be valid for the branch‐to‐run pipe ratios of radius and of thickness from 0.0 to 1.0, and the mean radius‐to‐thickness ratio of the run pipe from 5.0 to 20.0.

Effects of the Bend Angle and the Length of the Attached Straight Pipe on Plastic Loads for Pipe Bends

2007 ◽  
Author(s):  
Chang-Sik Oh ◽  
Yun-Jae Kim
Keyword(s):  
Limit Load ◽  
Small Strain ◽  
Bend Angle ◽  
Plastic Limit ◽  
Straight Pipe ◽  
Pipe Bend ◽  
Limit Loads ◽  
Perfectly Plastic ◽  
Plastic Materials ◽  
Elastic Perfectly Plastic

This paper quantifies effects of the bend angle and the length of the attached straight pipe on plastic limit loads of the 90° pipe bend, based on small strain FE limit analyses using elastic-perfectly plastic materials with the small geometry change option. It is found that the effect of the length of the attached straight pipe on plastic limit loads can be significant, and the limit loads tend to decrease with decrease of the length of the attached straight pipe. Regarding the effect of the bend angle, it is found the plastic load smoothly changes from the limit load of the straight pipe when the bend angle approaches zero to the plastic load of the 90° pipe bend when the bend angle approaches 90 degree.

The Elastic-Softening Failure of Floating Beams

1988 ◽  
Vol 32 (01) ◽  
pp. 37-43
Author(s):  
Paul C. Xirouchakis
Keyword(s):  
Carrying Capacity ◽  
Maximum Load ◽  
Point Load ◽  
Negative Stiffness ◽  
Load Carrying Capacity ◽  
Perfectly Plastic ◽  
Load Carrying ◽  
Elastic Perfectly Plastic ◽  
The Moment ◽  
Elastic Softening

The solution is presented for an infinite elastic-softening floating beam under a point load. The response depends on two nondimensional parameters: the negative stiffness coefficient that characterizes the descending part of the moment-curvature curve, and the nondimensional softening region half-length. The solution exhibits two important features that the elastic-perfectly plastic solution does not show. First, in certain ranges of parameters, the elastic-softening beam has a clearly defined maximum load carrying capacity. Second, in some other ranges of parameters, the elastic-softening beam has a minimum load or residual strength. The beam stiffens up upon further deformation due to the reactions of the water foundation. Critical softening parameters are calculated that separate stable from unstable behavior.

Effects of Torsion on Equivalent Bending Moment for Limit Load and EPFM Circumferential Pipe Flaw Evaluations

2012 ◽  
Vol 134 (6) ◽  
Author(s):  
Phuong H. Hoang ◽  
Kunio Hasegawa ◽  
Bostjan Bezensek ◽  
Yinsheng Li
Keyword(s):  
Finite Element ◽  
Pressure Vessel ◽  
Large Strain ◽  
Bending Moment ◽  
Limit Load ◽  
Elastic Plastic ◽  
Perfectly Plastic ◽  
Plastic Materials ◽  
Weighted Factor ◽  
Elastic Perfectly Plastic

The circumferential flaw evaluation procedures in ASME Boiler and Pressure Vessel Code Section XI nonmandatory Appendix C are currently limited to straight pipes under pressure and bending loads without consideration of torsion loading. The Working Group on Pipe Flaw Evaluation of the ASME Boiler and Pressure Vessel Code is developing guidance for considering the effects of torsion by a mean of an equivalent bending moment, which is a square root of sum square combination of bending moment and torsion load with a weighted factor for torsion moment. A torsion weighted factor, Ce, is established in this paper using large strain finite element limit load analysis with elastic perfectly plastic materials. Planar flaws and nonplanar flaws in a 10.75 in. (273 mm) OD pipe are investigated. Additionally, a finite element J-integral calculation is performed for a planar through wall circumferential flaw with elastic plastic materials subjected to bending and torsion load combinations. The proposed Ce factor for planar flaws is intended for use with the ASME B&PV Code Section XI, Appendix C for limit load and Elastic Plastic Fracture Mechanics (EPFM) circumferential planar flaw evaluations.

Plastic Limit Loads for Through-Wall Cracked Pipes Using Finite Element Limit Analysis

2006 ◽  
Vol 321-323 ◽  
pp. 724-728
Author(s):  
Nam Su Huh ◽  
Yoon Suk Chang ◽  
Young Jin Kim
Keyword(s):  
Finite Element ◽  
Limit Analysis ◽  
Structural Integrity ◽  
Three Dimensional ◽  
Limit Load ◽  
Plastic Behavior ◽  
Plastic Limit ◽  
Integrity Assessment ◽  
Perfectly Plastic ◽  
Elastic Perfectly Plastic

The present paper provides plastic limit load solutions for axial and circumferential through-wall cracked pipes based on detailed three-dimensional (3-D) finite element (FE) limit analysis using elastic-perfectly plastic behavior. As a loading condition, both single and combined loadings are considered. Being based on detailed 3-D FE limit analysis, the present solutions are believed to be valuable information for structural integrity assessment of cracked pipes.

Finite Element Limit Loads for Circumferential Through-Wall Cracked Pipe Bends Under In-Plane Bending

2006 ◽  
Author(s):  
Yun-Jae Kim ◽  
Chang-Sik Oh ◽  
Young-Il Kim ◽  
Chi-Yong Park
Keyword(s):  
Finite Element ◽  
Three Dimensional ◽  
Small Strain ◽  
Plastic Limit ◽  
Crack Location ◽  
Perfectly Plastic ◽  
Dimensional Finite Element ◽  
Plane Bending ◽  
Elastic Perfectly Plastic ◽  
Three Dimensional Finite Element

This paper proposes plastic limit and collapse loads for circumferential through-wall cracked pipe bends under in-plane bending, based on three-dimensional finite element limit analyses. The material is assumed to be elastic-perfectly-plastic, but both the geometrically linear (small strain) and the geometrically nonlinear (large geometry change) options are employed. Regarding crack location, both extrados and intrados cracks are considered. Moreover, for practical application, closed-form approximations of plastic limit and collapse loads are proposed based on the FE results, and compared with corresponding solutions for straight pipes.

Net-Section Limit Pressure and Engineering J Estimates for Axial Part-Through Surface Cracked Pipes

2007 ◽  
Author(s):  
Yun-Jae Kim ◽  
Chang-Sik Oh ◽  
Tae-Kwang Song
Keyword(s):  
Estimation Method ◽  
Small Strain ◽  
Perfectly Plastic ◽  
Reference Stress ◽  
Plastic Materials ◽  
Axial Part ◽  
Elastic Perfectly Plastic ◽  
Axial Surface ◽  
Good Agreement ◽  
J Estimation

This paper provides net-section limit pressures and a reference stress based J estimation method for pipes with internal axial surface cracks under internal pressure. Based on systematic small strain FE limit analyses using elastic-perfectly plastic materials, closed-form approximations of net-section limit pressures are presented. Then, based on proposed net-section limit moments, a method to estimate elastic-plastic J is proposed based on the reference stress approach. Comparison with extensive FE results shows overall good agreement.

Sign in / Sign up

Export Citation Format

Share Document