Research on Thermal Resistance of Micro Heat Pipe with Sintered Wick

2013 ◽  
Vol 589-590 ◽  
pp. 552-558
Author(s):  
Xi Bing Li ◽  
Xun Wang ◽  
Yun Shi Ma ◽  
Zhong Liang Cao
Keyword(s):  
Heat Transfer ◽  
Thermal Resistance ◽  
Heat Pipe ◽  
Heat Transfer Performance ◽  
High Heat ◽  
Working Fluid ◽  
Transfer Performance ◽  
Total Thermal Resistance ◽  
Vapor Cavity ◽  
Micro Heat Pipe

As a highly efficient heat dissipation unit, a micro heat pipe is widely used in high heat flux microelectronic chips, and its thermal resistance is crucial to heat transfer capacity. Through analyses of the structure and heat transfer performance of a circular heat pipe with sintered wick, the theoretical model of total thermal resistance was established on heat transfer theory, and then simplified, finally a testing platform was set up to test for total thermal resistance performance. The testing results show that when the micro heat pipe is in optimal heat transfer state, its total thermal resistance conform well with that from the theoretical model, and its actual thermal resistance is much lower than that of the rod made of the material with perfect thermal conductivity and of the same geometric size. With the increment of heat transfer capability, the total thermal resistance of a micro heat pipe with sintered wick decreases first, then increases and reaches the minimum when it is in the optimal heat transfer state. The greater total thermal resistance in low heat transfer performance is mainly caused by too much working fluid accumulating in evaporator and the lower velocity in vapor cavity, and the greater total thermal resistance in high heat transfer performance is mainly due to the working fluid drying up in condenser. Total thermal resistance is related to many factors, such as thermal conductivity of tube-shell material, wall thickness, wick thickness, copper powders grain size and porosity, the lengths of condenser and evaporator, and the diameter of vapor cavity etc.. Therefore, the structure parameters of a micro heat pipe with sintered wick should be reasonably designed according to the specific conditions to ensure its heat transfer capacity and total thermal resistance to meet the requirements.

Research on Thermal Resistance of Micro Heat Pipe with Trapezium-Grooved Wick

2016 ◽  
Vol 693 ◽  
pp. 395-402
Author(s):  
Xi Bing Li ◽  
Ming Jian Li ◽  
Ming Li ◽  
Ying Si Wan
Keyword(s):  
Heat Transfer ◽  
Thermal Resistance ◽  
Heat Pipe ◽  
Heat Transfer Performance ◽  
High Heat ◽  
Working Fluid ◽  
Transfer Performance ◽  
Total Thermal Resistance ◽  
Micro Heat Pipe ◽  
Heat Transfer Capacity

As an efficient heat conducting unit, micro heat pipe is widely used in high heat flux microelectronic chips, and thermal resistance is one of the factors that are crucial to its heat transfer capacity. Based on heat transfer theory, this paper established a theoretical model of total thermal resistance through analyzing the structure and heat transfer performance of circular heat pipe with trapezium-grooved wick, simplified the model and tested the micro heat pipe for its total thermal resistance performance by setting up a testing platform. The testing results show that when the micro heat pipe is in the optimal heat transfer state, its total thermal resistance well coincides with that from the established theoretical model. As for a micro heat pipe with trapezium-grooved wick, its total thermal resistance first decreases, then increases with heat transfer capability increment, and reaches the minimum when it is in the optimal state of heat transfer performance. That too much working fluid accumulates in evaporation section and the vapor velocity is rather low is the main cause for the greater thermal resistance when the pipe is in low heat transfer quantity, yet the greater total thermal resistance when the pipe is in high heat transfer quantity is mainly caused by the working fluid drying up in condensation section. The total thermal resistance is related to many factors, such as the thermal conductivity of tube-shell material, wall thickness, wick thickness, the number of the grooves, the lengths of condensation and evaporation sections, the diameter of vapor cavity etc.. Therefore, the structure parameters of a micro heat pipe with trapezium-grooved wick should be rationally designed according to specific conditions to ensure its heat transfer capacity and total thermal resistance to meet the requirements and be in the optimal state.

Working Fluid Inventory Effect on Heat Transfer Performance of a Grooved Micro Heat Pipe

2013 ◽  
Vol 589-590 ◽  
pp. 559-564
Author(s):  
Xi Bing Li ◽  
Yun Shi Ma ◽  
Xun Wang ◽  
Ming Li
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Pipe ◽  
Heat Transfer Performance ◽  
Mathematic Model ◽  
High Heat ◽  
Working Fluid ◽  
High Heat Flux ◽  
Transfer Performance ◽  
Flux Concentration

As a highly efficient heat transfer component, a micro heat pipe (MHP) has been widely applied to the situations with high heat flux concentration. However, a MHPs heat transfer performance is affected by many factors, among which, working fluid inventory has great influence on the security, reliability and frost resistance of its heat transfer performance. In order to determine the appropriate working fluid inventory for grooved MHPs, this paper first analyzed the working principle, major heat transfer limits and heat flux distribution law of grooved MHPs in electronic chips with high heat flux concentration, then established a mathematic model for the working fluid inventory in grooved MHPs. Finally, with distilled water being the working fluid, a series of experimental investigations were conducted at different temperatures to test the heat transfer performances of grooved MHPs, which were perfused with different inventories and with different adiabatic section lengths. The experimental results show that when the value of α is roughly within 0.40±0.05, a grooved MHP can acquire its best heat transfer performance, and the working fluid inventory can be determined by the proposed mathematic model. Therefore this study solves the complicated problem of determining appropriate working fluid inventory for grooved MHPs.

Heat Transfer Characteristic of Flat Trapezoid Grooved Micro Heat Pipes

2014 ◽  
Vol 609-610 ◽  
pp. 1526-1531 ◽  
Author(s):  
Yan Xia Yang ◽  
Xiao Dong Wang ◽  
Yi Luo ◽  
Liang Liang Zou
Keyword(s):  
Heat Transfer ◽  
Heat Pipe ◽  
Heat Transfer Performance ◽  
Capillary Flow ◽  
Transfer Characteristic ◽  
Fluid Distribution ◽  
Working Fluid ◽  
Transfer Performance ◽  
Maximum Heat ◽  
Micro Heat Pipe

To study the heat transfer performance of micro heat pipe, theoretical analysis of flat plate micro heat pipe with trapezoid cross section are presented in this paper. A one-dimensional stationary mathematical model for micro heat pipe grooved capillary flow using finite volume method (FVM) was established. The micro heat pipe had vapor space connect with each other and the influences of shear stress between vapor and fluid in the working process were described in the model which made the model more precisely. The axial variation of working fluid distribution in the heat pipe, pressure difference between vapor and liquid, and velocity of vapor and liquid were analyzed. In addition, the maximum heat transport capacity of micro heat pipe was calculated. The simulation results showed good agreement with the experiment results, and it could predict the heat transfer performance accurately, which was useful to micro heat pipe structural design.

Study of Nickel Wick Structure Applied to Loop Heat Pipe with Flat Evaporator

2016 ◽  
Vol 723 ◽  
pp. 282-287 ◽  
Author(s):  
Shen Chun Wu ◽  
Shih Hsuan Yen ◽  
Wei Chen Lo ◽  
Chen Yu Chung ◽  
Shen Jwu Su
Keyword(s):  
Heat Transfer ◽  
Surface Tension ◽  
Heat Pipe ◽  
Heat Transfer Performance ◽  
Working Fluid ◽  
Loop Heat Pipe ◽  
Transfer Performance ◽  
Total Thermal Resistance ◽  
Wick Structure ◽  
Flat Evaporator

This study investigated the use of sintered Nickel powder as the wick material of Loop heat pipe with flat evaporator (Flat loop heat pipe, FLHP) and its effect on the heat transfer performance. Add the 1-heptanol into water and form Self-rewetting Fluid (SRF), resulting in the Marangoni effect. The colder liquid can be transport to the heating surface, delaying the occurrence of dry-out and increasing the critical heat load. This paper use Surface tension measurements to measure the change of 1-heptanol SRF, then it was apply to nickel wick FLHP as working fluid to investigate its effect on the heat transfer performance. This study successfully established production process of Nickel wick structure. Results of wick structure for the effective pore radius of 2.6 μm, porosity of 62%, permeability of 5.7 × 10-13m2. Results of Surface tension measurements show that 1-heptanol aqueous solution’s surface tension increases with increasing temperature, Results from applying 0.1% 1-heptanol aqueous solution to FLHP as working fluid. For performance testing show that the critical heat load was 240 W and the total thermal resistance was 0.77 ° C/W. Compared with FLHP with pure water, SRF raised the maximum heat flux of 70%, the total thermal resistance of the system reduces 40%, SRF has the potential to enhance the heat transfer performance of FLHP.

Effect of Sintering Temperature Curve in Wick Manufactured for Loop Heat Pipe with Flat Evaporator

2014 ◽  
Vol 595 ◽  
pp. 24-29 ◽  
Author(s):  
Shen Chun Wu ◽  
Kuei Chi Lo ◽  
Jia Ruei Chen ◽  
Chen Yu Chung ◽  
Weie Jhih Lin ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Pipe ◽  
Heat Transfer Performance ◽  
Sintering Temperature ◽  
Temperature Curve ◽  
Loop Heat Pipe ◽  
Transfer Performance ◽  
Total Thermal Resistance ◽  
Flat Evaporator ◽  
Increasing Temperature

This paper specifically addresses the effect of the sintering temperature curve in manufacturing nickel powder capillary structure (wick) for a loop heat pipe (LHP) with flat evaporator. The sintering temperature curve is composed of three regions: a region of increasing temperature, a region of constant temperature, and a region of decreasing temperature. The most important region is the increasing temperature region, as the rate of temperature increase directly affects the performance of the wick.When the slope of the region of increasing temperature is 0.8 (equivalent to 8 OC/min), the structure of the manufactured wick is complete, with the best heat transfer performance result. Experimental resultsshowed that the optimal heat transfer performance is 160W, the minimal total thermal resistance is approximately 0.43OC/W, and the heat flux is 17W/cm2; the optimal wick manufactured has an effective pore radius of 5.2 μm, a permeability of 5.9×10-13m2, and a porosity of 64%.

Effect of working fluid on heat transfer performance of the anti-gravity loop-shaped heat pipe

2015 ◽  
Vol 88 ◽  
pp. 391-397 ◽  
Author(s):  
Hui Li ◽  
Bo Zhou ◽  
Yong Tang ◽  
Rui Zhou ◽  
Zhongshan Liu ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Pipe ◽  
Heat Transfer Performance ◽  
Working Fluid ◽  
Transfer Performance

Experimental Study on Oscillating Heat Pipe With Hydraulic Diameter Far Exceeding the Maximum Hydraulic Diameter

2019 ◽  
Author(s):  
Lilin Chu ◽  
Yulong Ji ◽  
Chunrong Yu ◽  
Yantao Li ◽  
Hongbin Ma ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Pipe ◽  
Heat Transfer Performance ◽  
Hydraulic Diameter ◽  
Working Fluid ◽  
Transfer Performance ◽  
Vertical Orientation ◽  
Oscillating Heat Pipe ◽  
Horizontal Orientation ◽  
Small Bubbles

Abstract In order to understand the heat transfer performance, startup and fluid flow condition of oscillating heat pipe (OHP) with hydraulic diameter far exceeding the maximum hydraulic diameter (MHD), an experimental investigation on heat transfer performance and visualization was conducted. From the experimental performance, it is found that the OHP can still work well with ethanol as the working fluid when the tube diameter has exceeded the MHD of 91.6%. In addition, the detailed flow patterns of the OHP were recorded by a highspeed camera for vertical and horizontal orientation to understand its physical mechanism. In the vertical orientation, initially working fluid generates small bubbles, and then the small bubbles coalesce and grow to vapor plugs, the vapor plugs finally pushes the liquid slugs to oscillate in the tube. In the horizontal orientation, the working fluid surface fluctuates due to the vapors flow from the evaporator to the condenser and bubbles burst in the evaporator. When the peak of liquid wave reaches the upper surface of tube, a liquid slug has been formed, and then the steam flow pushes the liquid slugs to oscillate in the tube.

Experimental Investigation of Oscillating Heat Pipe With Hybrid Fluids of Liquid Metal and Water

2019 ◽  
Vol 141 (7) ◽  
Author(s):  
Tingting Hao ◽  
Hongbin Ma ◽  
Xuehu Ma
Keyword(s):  
Heat Transfer ◽  
Liquid Metal ◽  
Heat Pipe ◽  
Heat Input ◽  
Heat Transfer Performance ◽  
Pure Water ◽  
Experimental Results ◽  
Working Fluid ◽  
Transfer Performance ◽  
Oscillating Heat Pipe

A new oscillating heat pipe (OHP) charged with hybrid fluids can improve thermal performance. The key difference in this OHP is that it uses room temperature liquid metal (Galinstan consisting of gallium, indium, and tin) and water as the working fluid. The OHP was fabricated on a copper plate with six turns and a 3 × 3 mm2 cross section. The OHP with hybrid fluids as the working fluid was investigated through visual observation and thermal measurement. Liquid metal was successfully driven to flow through the OHP by the pressure difference between the evaporator and the condenser without external force. Experimental results show that while added liquid metal can increase the heat transport capability, liquid metal oscillation amplitude decreases as the filling ratio of liquid metal increases. Visualization of experimental results show that liquid metal oscillation position and velocity increase as the heat input increases. Oscillating motion of liquid metal in the OHP significantly increases the heat transfer performance at high heat input. The lowest thermal resistance of 0.076 °C/W was achieved in the hybrid fluids-filled OHP with a heat input of 420 W. We experimentally demonstrated a 13% higher heat transfer performance using liquid metal as the working fluid compared to an OHP charged with pure water.

Sign in / Sign up

Export Citation Format

Share Document