Discussion on Roundness of Non-Ferromagnetic Tube by Interior Magnetic Abrasive Finishing Using a Magnetic Machining Jig

2021 ◽  
Vol 1018 ◽  
pp. 105-110
Author(s):  
Jiang Nan Liu ◽  
Yan Hua Zou
Keyword(s):  
Stainless Steel ◽  
Dynamic Equation ◽  
Steel Tube ◽  
Experimental Results ◽  
Stainless Steel Tube ◽  
Helical Motion ◽  
Magnetic Pole ◽  
Magnetic Abrasive Finishing ◽  
Sus304 Stainless Steel ◽  
Abrasive Finishing

In this study, mainly researching the improvement of roundness of thick SUS304 stainless steel tube by interior magnetic abrasive finishing using a magnetic machining jig. The influence of reciprocating velocity of magnetic pole unit on the improvement of roundness of interior surface was studied by establishing the dynamic equation of magnetic machining jig. Experimental results showed that low reciprocating velocity of magnetic pole unit is conducive to the improvement of interior roundness of the thick SUS304 stainless steel tube. The reason is that the low reciprocating velocity of magnetic pole unit reduces the pitch of the helical motion and can produce greater finishing force of the magnetic machining jig.

Improving the Polishing Effect of Stainless Tube by Magnetic Finishing with Gel Abrasive

2015 ◽  
Vol 656-657 ◽  
pp. 289-295
Author(s):  
A. Cheng Wang ◽  
Lung Tsai ◽  
Chun Ho Liu ◽  
Yan Cherng Lin
Keyword(s):  
Stainless Steel ◽  
Flow Property ◽  
Steel Tube ◽  
Stainless Steel Tube ◽  
Uniform Motion ◽  
Abrasive Particles ◽  
Sus304 Stainless Steel ◽  
Novel Approach ◽  
Abrasive Finishing ◽  
The Stability

Magnetic abrasive finishing (MAF) is a fast and high-precision polishing method. However, the magnetic force acting on abrasive particles will decrease remarkably when polishing stainless steel tubes with the property of non-permeability, such as the SUS304 stainless steel. Moreover, the abrasive particles will be moved off the surface of machining area due to the centrifugal force of rotation, resulting in reducing the stability of polishing process. Therefore, this study developed a novel approach by adopting different gels as the bonding materials to combine the magnetic abrasive particles with hard abrasive particles to create a series of magnetic abrasive gels. Generally, those abrasive gels have higher viscosity to dominate the flow property that will constrain uniform motion of the abrasive particles in MAF, and the abrasive gels can be tightly contacted to the wall surface to increase the stability of polishing. This investigation utilized the optimal parameters out of Taguchi method to polish SUS304 stainless steel tube for 30 minutes—the value of surface roughness can be reduced from 0.636μm Ra to 0.05μm Ra, which can be improved by 92.1%, and the amount of material remove rate is as high as 218.4mg.

Uniform Internal Finishing of SUS304 Stainless Steel Bent Tube Using a Magnetic Abrasive Finishing Process

2004 ◽  
Vol 127 (3) ◽  
pp. 605-611 ◽  
Author(s):  
Hitomi Yamaguchi ◽  
Takeo Shinmura ◽  
Megumi Sekine
Keyword(s):  
Magnetic Field ◽  
Stainless Steel ◽  
Removal Rate ◽  
Surface Finishing ◽  
Initial Surface ◽  
Magnetic Abrasive Finishing ◽  
Sus304 Stainless Steel ◽  
Finishing Process ◽  
Abrasive Finishing ◽  
The Magnetic Field

This research studies the factors affecting the conditions required for successful uniform internal finishing of SUS304 stainless steel bent tube by a Magnetic abrasive finishing process. In particular, the effects of the magnetic field and ferrous particles were investigated. Local intensification of the magnetic field is accomplished by offsetting the axis of pole rotation from elbow axis. This effect enables local control of the material removal rate, which leads to uniformity in the finished surface regardless of the initial surface conditions. A two-phase finishing process controlling the size of the ferrous particles is proposed to achieve efficient fine surface finishing.

Dynamic Analysis and Experimental Measurements for a Single Fluid Heat Exchanger

1966 ◽  
Vol 88 (1) ◽  
pp. 137-139 ◽  
Author(s):  
P. S. Lall ◽  
R. J. Schoenhals
Keyword(s):  
Stainless Steel ◽  
Heat Exchanger ◽  
Dynamic Response ◽  
Dynamic Analysis ◽  
Coordinate System ◽  
Steel Tube ◽  
Experimental Results ◽  
Stainless Steel Tube ◽  
Experimental Measurements ◽  
Thin Walled

The Lagrangian method of description was used, as opposed to the Eulerian coordinate system, in studying the dynamic response of a single fluid heat exchanger. Experimental measurements are reported for a heated thin walled stainless steel tube. Comparison of the analytical and experimental results is given.

Transformations of hydrocarbon radicals moving along a stainless steel tube

2010 ◽  
Vol 4 (6) ◽  
pp. 928-934
Author(s):  
A. E. Gorodetskii ◽  
V. L. Bukhovets ◽  
R. Kh. Zalavutdinov ◽  
A. P. Zakharov
Keyword(s):  
Stainless Steel ◽  
Steel Tube ◽  
Stainless Steel Tube ◽  
Hydrocarbon Radicals

Production Process and Heat Transfer Performance of 10/316 Clad Tube

2014 ◽  
Vol 1081 ◽  
pp. 270-274
Author(s):  
Zui Xian Yu ◽  
Xue Sheng Wang ◽  
Qin Zhu Chen
Keyword(s):  
Heat Transfer ◽  
Stainless Steel ◽  
Heat Transfer Coefficient ◽  
Carbon Steel ◽  
Transfer Coefficient ◽  
Heat Transfer Performance ◽  
Steel Tube ◽  
Stainless Steel Tube ◽  
Transfer Performance ◽  
Clad Tube

A new preparation technique of carbon steel/stainless steel clad tube was introduced, and the contact surface was well combined. Meanwhile, with the using of tube heat exchanger, the experiment on the heat transfer performance of the clad tube was done. Comparing the 10/316 clad tube and the 316 stainless steel tube, the effects on the heat transfer performance of 316 stainless steel tube attached to carbon steel was evaluated. It is showed that overall heat transfer coefficient of 10/316 clad tubes is higher than that of stainless steel tube. The average heat transfer coefficient of 10/316 clad tubes is about 18.7%~34.4% higher than that of stainless steel tube. Experimental investigation indicates that, by brazing and cold drawing, the 10/316 clad tube was well combined and the thermal conductivity was better than that of stainless steel tube.

Sign in / Sign up

Export Citation Format

Share Document