scholarly journals Inter- and Intragranular Stress Determination with Kossel Microdiffraction in a Scanning Electron Microscope

2006 ◽  
Vol 524-525 ◽  
pp. 109-114 ◽  
Author(s):  
Raphaël Pesci ◽  
Karim Inal ◽  
Sophie Berveiller ◽  
Etienne Patoor ◽  
Jean Sébastien Lecomte ◽  
...  
Keyword(s):  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Ccd Camera ◽  
Stress Sensitivity ◽  
In Situ Tests ◽  
Set Up ◽  
Line Patterns ◽  
Electron Back Scattered Diffraction ◽  
Scanning Electron

A Kossel microdiffraction experimental set up is under development inside a Scanning Electron Microscope (SEM) in order to determine the crystallographic orientation as well as the inter- and intragranular strains and stresses on the micron scale, using a one cubic micrometer spot. The experimental Kossel line patterns are obtained by way of a CCD camera and are then fully indexed using a home-made simulation program. The so-determined orientation is compared with Electron Back-Scattered Diffraction (EBSD) results, and in-situ tests are performed inside the SEM using a tensile/compressive machine. The aim is to verify a 50MPa stress sensitivity for this technique and to take advantage from this microscope environment to associate microstructure observations (slip lines, particle decohesion, crack initiation) with determined stress analyses.

Detection of the Fracture Path under Tensile Loads through in situ Tests in an ESEM Chamber

Holzforschung ◽  
2003 ◽  
Vol 57 (3) ◽  
pp. 326-332 ◽  
Author(s):  
K. Frühmann ◽  
I. Burgert ◽  
S. E. Stanzl-Tschegg
Keyword(s):  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Tensile Tests ◽  
Specimen Size ◽  
Environmental Scanning ◽  
Fracture Path ◽  
Cooling Device ◽  
In Situ Tests ◽  
Scanning Electron

Summary In situ tensile tests parallel to the grain were carried out in an Environmental Scanning Electron Microscope (ESEM) chamber on Norway spruce (Picea abies [L.] Karst.) samples. The ESEM-mode combined with a cooling device allowed examination of the specimens at a moisture content of 12% with unsputtered surfaces. By recording load-displacement curves and observing crack propagation simultaneously, a detailed image of fracture progress and tissue interaction could be described. Since these experiments required a sufficient specimen size and geometry, focus was concentrated on the methodology.

Effect of Briquetting Pressure on the Performance of In Situ Formed Sialon in Al2O3-C Refractory Bricks

2014 ◽  
Vol 881-883 ◽  
pp. 1049-1052 ◽  
Author(s):  
Nai Peng ◽  
Cheng Ji Deng ◽  
Hong Xi Zhu
Keyword(s):  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
X Ray Diffraction ◽  
X Ray ◽  
Z Value ◽  
Refractory Bricks ◽  
Scanning Electron

In this paper, the effects of briquetting pressure on the performance of in-situ formed Sialon in Al2O3-C refractory bricks are investigated. The phase compositions and microstructure of the Al2O3-C refractory were investigated by X-ray diffraction (XRD) and scanning electron microscope (SEM).The results show the briquetting pressure hardly has effect on the phase of the sintered specimens, two new phases of Sialon with a Z value of 2 and SiC formed. The micrographs of Sialon crystals have the shape of both column and tabular column, but with a cone tip in the specimens sintered at 200MPa and 300MPa and smooth tip in specimens sintered at 400MPa and 500MPa.

In-situ Fracturing of Wood in the Scanning Electron Microscope

Holzforschung ◽  
1996 ◽  
Vol 50 (6) ◽  
pp. 487-490 ◽  
Author(s):  
Josef Bodner ◽  
Gerhard Grüll ◽  
Michael Georg Schlag
Keyword(s):  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Scanning Electron

scholarly journals Influence of Multi-Holes on Fatigue Behaviors of Cast Magnesium Alloys Based on In-Situ Scanning Electron Microscope Technology

Materials ◽  
2018 ◽  
Vol 11 (9) ◽  
pp. 1700 ◽  
Author(s):  
Xi-Shu Wang ◽  
Chang-Hao Tan ◽  
Juan Ma ◽  
Xiao-Dong Zhu ◽  
Qing-Yuan Wang
Keyword(s):  
Fatigue Crack ◽  
Electron Microscope ◽  
Crack Initiation ◽  
Scanning Electron Microscope ◽  
Magnesium Alloys ◽  
Mg17al12 Phase ◽  
Cast Magnesium Alloys ◽  
Cast Magnesium ◽  
Scanning Electron

The low cycle fatigue tests on the crack initiation and propagation of cast magnesium alloys with two small holes were carried out by using in-situ scanning electron microscope (SEM) observation technology. The fatigue crack propagation behaviors and fatigue life, which are affected by two small artificial through holes, including the distances between two holes and their locations, were discussed in detail based on the experimental results and the finite element analysis (FEA). The results indicated that the fatigue multi-cracks occurred chiefly at the edges of two holes and the main crack propagation was along the weak dendrite boundary with the plastic deformation vestiges on the surface of α-Mg phase of cast AM50 and AM60B alloys. The fatigue cracking characteristics of cast AZ91 alloy depended mainly on the brittle properties of β-Mg17Al12 phase, in which the multi-cracks occurred still at the edges of two holes and boundaries of β-Mg17Al12 phase. The fatigue crack initiation position of cast magnesium alloys depends strongly on the radius of curvature of through hole or stress concentration factor at the closed edges of two through holes. In addition, the fatigue multi-cracks were amalgamated for the samples with titled 45° of two small holes of cast Mg-Al alloys when the hole distance is less than 4D (D is the diameter of the small hole).

scholarly journals Construction of in situ degradation bacteria of corn straw and analysis of its degradation efficiency

2020 ◽  
Vol 70 (1) ◽  
Author(s):  
Xiujie Gong ◽  
Hongtao Zou ◽  
Chunrong Qian ◽  
Yang Yu ◽  
Yubo Hao ◽  
...  
Keyword(s):  
Fourier Transform ◽  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Degradation Efficiency ◽  
Corn Straw ◽  
X Ray ◽  
In Situ Degradation ◽  
Infrared Spectrometer ◽  
Scanning Electron

Abstract Purpose The highly efficient degradation bacteria were selected from the humus from the very cold straw in China for many years to construct the in situ degradation bacteria, and the degradation efficiency of corn straw was determined by process optimization. Methods According to the main components of corn straw, through morphological, physiological, and biochemical screening, three highly efficient complementary degradation strains were selected to construct the compound flora, and the degradation efficiency was analyzed by Fourier transform infrared spectrometer, field emission scanning electron microscope, and X-ray diffractometer. Result The corn straw selected in this paper is mainly composed of cellulose (31.99%), hemicellulose (25.33%), and lignin (14.67%). Through the determination of enzyme activity, strain Streptomyces sp. G1T has high decomposition ability to cellulose and hemicellulose but weak utilization ability to lignin; strain Streptomyces sp. G2T has the strongest decomposition ability to cellulose and hemicellulose among the three strains. The decomposition ability of strain Streptomyces sp. G3T to lignin was the strongest among the three strains. Therefore, by compounding the three strains, the decomposition ability has been greatly improved. The optimal process conditions obtained by single factor and response surface method are as follows: pH is 7, temperature is 30 °C, inoculation amount is 5%, rotational speed is 210 rpm, and the weight loss rate of straw is 60.55% after decomposing for 7 days. A large amount of degradation of corn straw can be seen by Fourier transform infrared spectrometer, field emission scanning electron microscope, and X-ray diffractometer. Conclusion Streptomyces sp. G1T, Streptomyces sp. G2T, and Streptomyces sp. G3T screened from straw humus in very cold areas were used to construct in situ degradation bacteria, which had good straw degradation activity and had the potential to be used for straw treatment in cold areas after harvest. This characteristic makes the complex bacteria become a strong competitive candidate for industrial production, and it is also an effective biotechnology in line with the current recycling of resources.

Sign in / Sign up

Export Citation Format

Share Document