Superplasticity in Ultrahigh Carbon (1.6 Pct C) Steel

2007 ◽  
Vol 551-552 ◽  
pp. 199-202 ◽  
Author(s):  
Zhan Ling Zhang ◽  
Yong Ning Liu ◽  
Jie Wu Zhu ◽  
G. Yu
Keyword(s):  
Grain Boundary ◽  
Superplastic Deformation ◽  
Boundary Diffusion ◽  
Grain Boundary Sliding ◽  
Strain Rates ◽  
Ultrahigh Carbon Steel ◽  
Elongation To Failure ◽  
Boundary Sliding ◽  
Dynamic Grain Growth ◽  
Microduplex Structure

Ultrahigh carbon steel containing 1.6 wt pct C was processed to create microduplex structure consisting of fine-spheroidized carbides and fine ferrite grains. Elongation-to-failure tests were conducted at strain rates from 10-4s-1 to 15×10-4s-1, and at temperatures from 600 °C to 850 °C. The steel exhibited superplasticity at and above 700 °C when testing at a strain rate of 10-4s-1, and at 800 °C when testing at strain rates of 7×10-4s-1 and slower. The grains retained the equiaxed shape and initial size during deformation; dynamic grain growth was not observed after superplastic deformation, whereas carbide coarsening was observed. It is concluded that the fine ferrite grains or austensite grains are stabilized by the grain boundary carbides, and grain-boundary sliding controlled by grain boundary diffusion is the principal superplastic deformation mechanism at temperatures in the range of 700-850 °C.

Superplastic Deformation Behavior in Dual-Phase Mg-Ca Alloy

2016 ◽  
Vol 838-839 ◽  
pp. 256-260
Author(s):  
Takahiko Yano ◽  
Naoko Ikeo ◽  
Hiroyuki Watanabe ◽  
Toshiji Mukai
Keyword(s):  
Activation Energy ◽  
Grain Boundary ◽  
Deformation Behavior ◽  
Superplastic Deformation ◽  
Boundary Diffusion ◽  
Rate Sensitivity ◽  
Grain Boundary Sliding ◽  
Dual Phase ◽  
Elongation To Failure ◽  
Boundary Sliding

Superplastic deformation behavior was investigated for a dual-phase Mg-Ca alloy. The elongation-to-failure reached more than 120% with the strain rate sensitivity, m, over 0.4. The activation energy required for the deformation was estimated to be 98 kJ/mol which is close to the activation energy for grain boundary diffusion in magnesium. Therefore, the superplastic deformation mechanism was suggested to be the grain boundary sliding rate, which is controlled by boundary diffusion.

Superplastic Deformation Mechanisms in High Magnesium Contenting Aluminum Alloy

2016 ◽  
Vol 838-839 ◽  
pp. 66-71 ◽  
Author(s):  
O.A. Yakovtseva ◽  
Anastasia V. Mikhaylovskaya ◽  
A.G. Mochugovskiy ◽  
V.V. Cheverikin ◽  
Vladimir K. Portnoy
Keyword(s):  
Activation Energy ◽  
Grain Boundary ◽  
Superplastic Deformation ◽  
Effective Activation Energy ◽  
Grain Boundary Sliding ◽  
Deformation Mechanisms ◽  
Effective Activation ◽  
Continuous Formation ◽  
Boundary Sliding ◽  
Dynamic Grain Growth

The evolution of surface, grains and dislocation structures during superplastic deformation was studied in Al–6.8%Mg–0.6%Mn–0.25%Cr alloy by SEM, EBSD, TEM techniques. The effective activation energy of superplastic deformation was calculated. Contribution of grain boundary sliding was defined during superplastic deformation. Low value of grain boundary sliding, significant dynamic grain growth in stress direction, high dislocations activity and permanent continuous formation of sub-grain boundaries during superplastic deformation were found.

A Model for the Effects of Strain Rate and Temperature on the Deformation Behavior of Ultrafine-Grained Metals

2011 ◽  
Vol 291-294 ◽  
pp. 1173-1177
Author(s):  
Zi Ling Xie ◽  
Lin Zhu Sun ◽  
Fang Yang
Keyword(s):  
Grain Boundary ◽  
Strain Rate ◽  
Deformation Behavior ◽  
Boundary Diffusion ◽  
Rate Sensitivity ◽  
Grain Boundary Sliding ◽  
Dislocation Slip ◽  
Deformation Response ◽  
Ultrafine Grained ◽  
Boundary Sliding

A theoretical model is developed to account for the effects of strain rate and temperature on the deformation behavior of ultrafine-grained fcc Cu. Three mechanisms, including dislocation slip, grain boundary diffusion, and grain boundary sliding are considered to contribute to the deformation response simultaneously. Numerical simulations show that the strain rate sensitivity increases with decreasing grain size and strain rate, and that the flow stress and tensile ductility increase with either increasing strain rate or decreasing deformation temperature.

Analysis of Creep Deformation Due to Grain-Boundary Diffusion/Sliding

2007 ◽  
Vol 345-346 ◽  
pp. 565-568
Author(s):  
Byung Nam Kim ◽  
Keijiro Hiraga ◽  
Koji Morita ◽  
Hidehiro Yoshida
Keyword(s):  
Grain Size ◽  
Creep Rate ◽  
Grain Boundary ◽  
Boundary Diffusion ◽  
Effective Diffusion ◽  
High Viscosity ◽  
Grain Boundary Sliding ◽  
Grain Boundary Diffusion ◽  
Grain Sizes ◽  
Boundary Sliding

For steady-state deformation caused by grain-boundary diffusion and viscous grain-boundary sliding, the creep rate of regular polyhedral grains is analyzed by the energy-balance method. For the microstructure, the grain-grain interaction increases the degree of symmetry of diffusional field, resulting in a decrease of the effective diffusion distance. Meanwhile, the viscous grain-boundary sliding is found to decrease the creep rate. The present analysis reveals that the grain-size exponent is dependent on the grain size and the grain-boundary viscosity: the exponent becomes unity for small grain sizes and/or high viscosity, while it is three for large grain sizes and/or low viscosity.

Deformation Behavior of Fine Grained Al-Mg Alloy under Biaxial Stress

2006 ◽  
Vol 503-504 ◽  
pp. 475-480 ◽  
Author(s):  
Masafumi Noda ◽  
Kunio Funami
Keyword(s):  
Grain Boundary ◽  
Tensile Deformation ◽  
Grain Boundary Sliding ◽  
Biaxial Stress ◽  
Mg Alloy ◽  
Strain Rates ◽  
Fine Grained ◽  
Biaxial Tensile ◽  
Wide Range ◽  
Boundary Sliding

The grain boundary sliding and the formation of slipped bands and cavitations during biaxial tensile deformation were examined in fine grained Al-Mg alloy. Biaxial tensile testing was conducted with cruciform specimens at initial strain rates of 10-4 to 101s-1. It was found that at the same equivalent strain conditions, the number of cavities under biaxial tension is significantly greater than that under uniaxial tension. A greater prevalence of slipped bands and grain separations were clearly observed under biaxial stress than under uniaxial stress. It was suggested that development of slipped bands resulted from the formation of elongated cavities and multiple deformed bands under biaxial stress. Additionally, the m-value under biaxial stress remained at about 0.3 over a wide range of strain rates. The effects of grain separation and formation of cavities were related to the motion of grain boundary sliding, grain size and loading conditions.

Enhanced Tensile Ductility of AZ80 Magnesium Alloy

2011 ◽  
Vol 284-286 ◽  
pp. 1635-1638
Author(s):  
Jun Qiao ◽  
Yu Wang ◽  
Guo Dong Shi ◽  
Bao Xin Nie
Keyword(s):  
Tensile Tests ◽  
Grain Boundary Sliding ◽  
Dislocation Creep ◽  
Strain Rates ◽  
Premature Failure ◽  
Az80 Magnesium Alloy ◽  
Coarse Grains ◽  
Elongation To Failure ◽  
Boundary Sliding ◽  
Cavity Evolution

Tensile behaviors of extruded and rolled AZ80 Mg alloy were investigated with elongation-to-failure tensile tests at constant temperatures of 300 °C, 350 °C, 400 °C, and 450 °C, and constant strain rates of 10-2s-1and 10-3s-1. Experimental data show that the material exhibits tensile ductilities of over 100% at 400 °C and 450 °C, featured by long steady state deformation. Microstructure studies show that annealed coarse grains were remained in the gauge region during the tensile tests, and the enhanced tensile ductilities resulted from dislocation creep, other than dynamic recrystallization or grain boundary sliding. Cavity evolution and recrystallized coarse grains near fracture end caused premature failure of the material.

Sign in / Sign up

Export Citation Format

Share Document